Owner’s manual Mode d’emploi Manual de instrucciones ARX7570z AM/FMCASSETTEPLAYER WITHCD/MDCHANGERCONTROL • LECTEURDECASSETTEAM/FMAVEC COMMANDEDECHANGEURCD/MD • RADIODEAM/FMYREPRODUCTORDE CASETESCONCONTROLDECAMBIADORDE DISCOSCOMAPCTOS/MINIDISCOS OPEN ARX7570z ISR Clarion Co., Ltd. 1999/1 (A·C) All Rights Reserved. Copyright © 1998: Clarion Co., Ltd.
Thank you for purchasing the Clarion ARX7570z. ∗ Please read this owner’s manual in its entirety before operating this equipment. ∗ After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). ∗ Check the contents of the enclosed warranty card and keep it carefully with this manual. ∗ This manual includes the operating procedures of the CD changer, MD changer and TV tuner connected via the CeNET cable.
6. REMOTE CONTROL ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Receiver for remote control unit OPEN ARX7570z ISR 1 2 3 4 5 6 Operating range: 30° in all directions Remote control unit Handling Cassette Tapes 1. FEATURES Signal transmitter Using any of the following types of cassette tapes can cause malfunctions.
3. CONTROLS / LES COMMANDES / CONTROLES 4. NOMENCLATURE 5. DCP Note: • Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). Source unit / Appareil pilote / Unidad fuente Names of Buttons OPEN 1 OPEN button 8 Z-EHCR (z-enhancer) button 2 ENT (enter) button 9 Preset buttons (1 to 6) The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.
Functions of Remote Control Unit Buttons Button Mode Radio Tape CD changer MD changer TV ) FUNC Turns power on and off. When pressed and held for 1 second: Turns power off. Switches among radio, tape, CD changer, MD changer and TV. ¡ BAND DISC UP PROG TOP Switches reception band. ™ VOLUME Increases and decreases volume (in all modes). £ SEARCH Moves preset channels up and down. Fast-forward and rewinds tape. APC fast-forward and rewind. ¢ PLAY/PAUSE No function.
7. OPERATIONS Basic Operations Note: Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). CAUTION Be sure to lower the volume before switching off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and damage the unit.
Basic Operations Setting the Z-enhancer Adjusting the bass This unit comes with 3 types of sound tone effects stored in memory. Select the one you prefer. 1. Press A-M button # and select “BASS”. 2. Turning the Rotary knob % clockwise emphasizes the bass; turning it counterclockwise attenuates the bass. ∗ The factory default setting is “Z-EHCR OFF”.
Basic Operations Radio Operations Adjusting the Z-enhancer FM reception 1. Press Z-EHCR button 8 and select the Zenhancer mode (1 to 3) to adjust. 2. Press A-M button # and select “Z-EHCR”. 3. Turning the Rotary knob % clockwise adjusts in the + direction; turning it counterclockwise adjusts in the – direction. ® For enhanced FM performance the tuner includes signal actuated stereo control, Enhanced Multi AGC, Impulse noise reduction circuits and Multipath noise reduction circuits.
Radio Operations Manual tuning Auto store There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In quick tuning mode, you can quickly tune the desired frequency. 1. Press BND button @ and select the desired band (FM or AM). Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially.
Tape Operations Loading a tape Ejecting a tape 1. Press OPEN button 1 to access the cassette tape insertion slot behind the FLIP DOWN PANEL. 2. Load a tape into the cassette tape insertion slot. “LOADING” appears in the display and starts playing. 1. Press OPEN button 1 to access the cassette Eject button & behind the FLIP DOWN PANEL. 2. Press Eject button & to eject a tape and take it out. 3. Close the FLIP DOWN PANEL.
Tape Operations APC (Auto Program Control) function The APC function allows the tape to skip forward to the beginning of the next track or rewind to the start of the current track. ● Skipping forward to the next track (“APCFF”) During tape playback, press the right side of SEARCH button $ twice to fast-forward to the next track. The next track starts playing.
Other Handy Functions Setting the clock Entering titles 1. Press and hold ADJ button 4 for 1 second or longer to switch to the adjustment selection display. 2. Press the right or left side of SEARCH button $ to select “CLOCK”. 3. Press ENT button 2. 4. Press the right or left side of SEARCH button $ to select the hour or the minute. 5. Turn the Rotary knob % clockwise or counterclockwise to set the correct time.
Other Handy Functions 4. Press BND button @. 5. Press and hold ENT button 2 for 2 seconds or longer to clear the title and cancel the title input mode. Triggered audio mute for cellular telephones Adjusting the display contrast ∗ This function is not compatible with all cellular telephones. Contact your local authorized Clarion dealer for information on proper installation and compatibility. You can adjust the display contrast according to the angle of installation of the unit.
8. OPERATIONS OF ACCESSORIES CD Changer Operations CD changer functions Selecting a CD When an optional CD changer is connected through the CeNET cable, this unit controls all the CD changer functions. This unit can control a total of 2 changers (MD and/or CD). Press FNC button 3 and select the CD changer mode to start play. If 2 CD changers are connected, press FNC button 3 to select the CD changer for play. Each of the Direct button 9 corresponds to a disc loaded into the magazine.
CD Changer Operations Top function Disc repeat play The top function plays from the first track (track No. 1) of the disc. ● When playing a disc 1 to 6 Press the Direct button 9 (1 to 6) with the same number as the CD playing. ● When playing a disc 7 to 12 (only when a 12 disc CD changer is used). Press and hold for 1 second or longer the Direct button 9 (7 to 12) with the same number as the CD playing.
MD Changer Operations MD changer functions When an optional MD changer is connected through the CeNET cable, this unit controls all the MD changer functions. This unit can control a total of 2 changers (MD and/or CD). Press FNC button 3 and select the MD changer mode to start play. If 2 MD changers are connected, press FNC button 3 to select the MD changer for play. ∗ If “NO DISC” appears in the display, load MDs into the MD changer. 2.
MD Changer Operations TV Operations Repeat play TV tuner functions The repeat play continuously plays the current track. This function continues automatically until it is canceled. 1. Press RPT button 6. “RPT” lights in the display and the current track is repeated. 2. To cancel the repeat play, press RPT button 6 again. “RPT” goes off from the display and normal play resumes. When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions.
TV Operations Manual tuning There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In quick tuning mode, you can quickly tune the desired frequency. 1. Press BND button @ and select the desired band (TV1 or TV2). ∗ If “MANU” is not lit in the display, press and hold BND button @ for 1 second or longer. “MANU” lights in the display and manual tuning is now available. 2. Tune into a station.
9. TROUBLESHOOTING General Problem Cause Fuse is blown. Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. No sound output when operating the unit with amplifiers or power antenna attached. Power antenna lead is shorted to ground or excessive current is required for remote-on the amplifiers or power antenna. 1. Turn the unit off. 2. Remove all wires attached to the power antenna lead.
10. ERROR DISPLAYS If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. MD changer CD changer Tape Error Display Cause Measure ERROR 1 Tape cannot be played due to defective tape such as cut tape. Eject the tape then replace it with a new one. ERROR 2 Tape is caught and cannot be played. Remove the caught or wound tape. ERROR 4 Tape mode cannot be detected.
11. SPECIFICATIONS FM Tuner Audio Frequency Range: 87.9 MHz to 107.9 MHz Usable Sensitivity: 11 dBf 50dB Quieting Sensitivity: 17 dBf Alternate Channel Selectivity: 75 dB Stereo Separation (1 kHz): 35 dB Frequency Response (±3 dB): 30 Hz to 15 kHz Maximum Power Output: 160 W (40 W × 4 ch) (EIAJ) Continuous Average Power Output: 14 W × 4, into 4 Ω, 20 Hz to 20 kHz, 1%THD Bass Control Action (30 Hz): ±15 dB Treble Control Action (10 kHz): ±10 dB Line Output Level (0VU tape): 0.
Memo 26 ARX7570z