Owner s manual & Installation manual Mode d emploi et manuel d installation Manual de instrucciones y manual de instalación Manuale dell utente e manuale di installazione Bedienungsanleitung und Installationshandbuch Bruksanvisning och installationsmanual CJ-7600E 7.0 WIDE TFT LCD COLOR MONITOR MONITEUR COULEUR TFT 7,0 DE LARGE MONITOR ANCHO TFT LCD COLOR DE 7,0 AMPIO MONITOR A COLORI LCD TFT DA 7 7.0 -BREITBILD-TFT-LCD-FARBMONITOR 7.
CONTENTS English 1.SAFETY INSTRUCTIONS ....................................................................................................... 3 4 2.BEFORE USE ..................................................................................................................................... 5 3.FEATURES ......................................................................................................................................... 6 4.CONTENTS ...................................................
1. SAFETY INSTRUCTIONS WARNING This information is for preventing bodily harm or even death and user should follow these safety rules. CAUTION This information is for preventing damage or shortening the life time of the products. ATTENTION This information is for user s reference for better usability. English Please read the Safety Rules carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product.
English CAUTION ● Disconnect battery before installation. Re-connect once installation is complete. Prevents electric shock or short circuit. ● Do not use for long periods without engine running. It may cause battery to go flat. ● The rear-view monitor image has the same right-left inversion as your vehicle s rearview mirrors. Depending on the vehicle, the field and angle of view may differ. ● Do not use multi socket or extended adaptor. It may cause unexpected overheating, fire and malfunction.
2. BEFORE USE ● Use the product at the temperature range of -10°C 60°C. English Precautions (when you use the monitor) ● Screen may be a little dark when the product is operated in low temperature areas. Screen will show normal luminosity after a few minutes. ● Do not disassemble and modify the product in any way. This may cause fire and/or electric shock. ● When you install the product in a vehicle and watch the monitor, the car engine should be running to avoid flattening the battery.
3.
5.
6. FUNCTION English 1 Power On/Stand-by Press POWER「 」button on monitor then the picture of the camera will be shown on the monitor. 2 Volume control ① Press and hold the ENT(VOL) button in the AV or main camera screen to display the set volume. ② The volume can be controlled with the ▲/▼ buttons. ❶ ❷ 3 Switch input video ① Press the AV button to switch to the AV (external input) screen and press it again to return to the previous screen.
① When a single signal (main, sub) is entered, the camera image corresponding to this is displayed. If the signal is terminated, the display returns to the previous screen. ※ When the hazard off terminal is connected to the left winker (sub-trigger terminal is connected to the right winker), even if a hazard signal is input, the system recognizes the hazard, and the display does not switch to the sub-camera image.
English General 1) Volume control ① Select [Volume] in the [General] menu and press the ENT(VOL) button. ② Press the ▲/▼ buttons to adjust the volume. ※ The volume can be adjusted between 0 and 15. The initial setting is 5. General Volume Language To initial settings General 5 English Volume Language To initial settings 5 English 2) Language settings ① Select [Language] in the [General] menu with the ▲/▼ buttons and press the ENT(VOL) button.
① Select [Brightness], [Tone], [Vividness] and [Dimmer] in the [Color tone] menu with the ▲/▼ buttons and press the ENT(VOL) button. Press the ▲/▼ buttons to adjust the [Brightness], [Tone] and [Vividness]. ② Select [Daytime], [Night], [Auto] and press the ENT(VOL) button to change the [Dimmer] setting.
English Marker Warning - The onscreen distance markers should be considered as a general reference to assist the driver in assessing the distances depicted on the screen. The distance markers have been designed based on the back camera installation conditions listed in the next section, but differences in vehicle design and construction may result in the actual installation condition or location being different from the conditions listed.
English 3) Marker type (set the marker pattern) ① Select [Marker type] in the [Marker] menu and press the ENT(VOL) button. ② Select [Type 1] to [Type 7] with the ▲/▼ buttons and press the ENT(VOL) button. Marker Marker Camera type Marker type Up/down L/R Type1 Type2 Type3 Type4 ON 118° Type1 0 0 ▼ ◆ Installation condition of back camera(distance marker input conditions) Camera type:118°,130° Marker No. (Pattern) Vehicle Width (From bumper toward rear) 7m Camera Install Height Type1 2.0 Type2 2.
English 4) Up/down, Left/Right adjustment (adjust the bumper position of the car) ① Select [Up/down] in the [Marker] menu and press the ENT(VOL) button. ② Adjust the V (vertical movement) value with the ▲/▼ buttons (▲: Up, ▼: Down). (V= −10∼+10, Default setting: V=0) Marker Marker Camera type Marker type Up/down L/R V:+10 H: 0 ON 118° Type1 0 0 ① Select [L/R] in the [Marker] menu and press the ENT(VOL) button. ② Adjust the H (horizontal movement) value with the ▲/▼ buttons (▲: Right, ▼: Left).
8. INSTALLATION (U-Bracket) English 1. Please ensure that the monitor is installed with enough room for heat to dissipate. Install the monitor stand with enclosed screws as per the picture. 2. Fix the monitor to the monitor stand firmly.
9. CONNECTIONS English ※1 Sub Main ※2 Audio input (white) ※1 ※2 B/U (yellow) DC12/24V Sub-trigger (blue) Hazard off Ground (black) ACC (red) DC12/24V Video input (yellow) Camera connecting cable Main trigger (violet/white) ※1 Use Clarion Cameras only. ※2 A camera connecting cable, sold separately, is required for connecting the camera. ■ When the B/U terminal is connected to the car s B/U: • When ACC is OFF, the shutter of the shutter camera closes automatically.
10. TROUBLESHOOTING Measure Is camera connected properly? Check the wiring to the camera and the camera connection. Power does not turn on. Is power cable connected properly? Check the wiring. Is a fuse blown out? Replace with a fuse of the same amperage (5A) Operating environment is inappropriate. Temperature in the vehicle is below -10° C or over 60° C. Check to see that the temperature in the vehicle is appropriate (around 25° C). Color is washed-out.
Clarion Co., Ltd. 2014/08 All Rights Reserved. Copyright © 2014: Clarion Co., Ltd.