Owner’s manual Mode d’emploi Bedienungsanleitung Istruzioni per l’uso Bruksanvisning DAB BLACK-BOX TUNER FOR CeNET • TUNER DE BOÎTE NOIRE DAB POUR CeNET • DAB BLACK-BOX-TUNER MIT ANSCHLUß UND STEUERUNG ÜBER CeNET • SINTONIZZATORE BLACK-BOX DAB PER CeNET • DAB BLACK-BOX TUNER FÖR CeNET Clarion Co., Ltd. 2001/12 (A·K) All Rights Reserved. Copyright © 2001: Clarion Co., Ltd.
Thank you for purchasing the Clarion DAH923. ∗ Please read this owner’s manual in its entirety before operating this equipment. ∗ Check the contents of the enclosed warranty card and keep it carefully with this manual. ∗ This manual includes the DAB operating procedures for four types of models and the installation procedures of the DAH923, DXZ928R, DXZ828R, DXZ728R and ADZ628R that are connected via the CeNET cables.
Digital Radio / DAB Operations Programme scan This function scans through each receivable programme in a DAB station being received for 10 seconds sequentially. This is useful when you want to search for a desired programme. 1. Press the [FNC] button to receive a DAB station. 2. Perform the following operation depending on the connected model. • DXZ928R/DXZ828R/DXZ728R Press the [PS/AS] button. “SERVICE SCN” lights up and the main unit starts scanning each programme for 10 seconds sequentially.
. CONTROLS / LES COMMANDES / REGLER / CONTROLLI / KONTROLLER CONTROLS / LES COMMANDES / REGLER / CONTROLLI / KONTROLLER Main unit / Appareil principal / Hauptgerät / Apparecchio principale / Huvudapparat DXZ928R Display / Afficheur / Display / Display / Display [ ], [ ] [FNC] [ ] [DISP] 5. NOMENCLATURE Notes: • Be sure to read this chapter referring to the front diagrams of chapter “4. CONTROLS” on pages 6 and 7 . • Only the buttons to operate the DAB function are shown in this manual.
Digital Radio / DAB Operations TA (Traffic Announcement) In TA standby mode, when a traffic announcement broadcast starts, the traffic announcement broadcast is received as top priority regardless of the function mode. Traffic programme (TP) automatic tuning is also possible. ∗ This function can only be used when “TP” is lit in the display. When “TP” is lit, this means that the DAB or RDS broadcast station being received has traffic announcement programmes.
Digital Radio / DAB Operations PTY This function enables you to listen to the selected programme type, irrespective of the function mode. ∗ One common PTY can be selected for DAB or RDS. ∗ Of DAB PTY and RDS PTY, the PTY which is received earlier takes priority over the other. ∗ PTY broadcasts are not yet available in all countries. ∗ In INFO standby mode, INFO stations have priority over PTY stations. ∗ In TA standby mode, TP stations have priority over PTY stations.
. INSTALLATION AND WIRE CONNECTION Before Installation 1. Before starting, be sure to disconnect the battery’s negative “−” terminal to prevent accidents due to short-circuits. 2. Location Consider safety and operability when selecting a place for installation. Avoid the following. • Locations where the unit will hamper driving. • Locations where the unit could injure passengers if the car stops suddenly. • Locations exposed to direct sunlight or hot air from the heater, etc.
Installation Example (Installing the unit under the driver’s seat) 1. Attach the mounting brackets 1 to the sides of the DAH923 using the screws 2 provided. 2. Select the location on the floor mat. Drill holes in the floor mat to match the positions of the holes in the mounting brackets 1. 3. Insert the canoe clips 3 from the rear of the floor mat and install the DAH923. ∗ There are three mounting holes on each side of the DAH923. Select the appropriate holes to match to the installation location.
How to Make Wirings 1. CeNET Cable Orient the CeNET cable in the direction shown in the figure and insert it until it is locked in position. To remove the CeNET cable, pull it by lightly grasping the slide cap A in your fingers. To remove the digital optical fibre cable, pull it by lightly grasping the slide cap B of the cable in your fingers. 3. DAB antenna Connect a DAB antenna (sold separately) to the DAB antenna input terminal 6. 2.
8. SYSTEM EXAMPLES 6 5 7 1 3 8 4 DAH923 2 1 Main unit compatible with CeNET connection 2 CD changer compatible with CeNET connection 3 CeNET cable (provided with the DAH923) Using this cable, connect the DAH923 to the main unit. 4 CeNET cable (provided with the CD changer) Using this cable, connect the DAH923 to the CD changer.
