Owner`s manual
Common
Operations
Setting
the
TV
diver
You
can
change
the reception setting
for
the
TV
antenna
connected
to the
TV
tuner.
1.
Press the
[A]
button to switch to the adjust
mode.
2.
Press the [.......]
or
[
........
IJ
button
to
select
''TV
DIVER".
3.
Turn
the [ROTARYJ knob
and
select
"ON"
or
"OFF".
•
ON:
Set
the
diver
setting to
ON
.
•
OFF:
Set
the
diver
setting to OFF.
4. Press
the
[A]
button to return to
the
previous
mode.
Selecting
A
UK
IN
sensitivity
Make
the
following
settings to
select
the
sensitivity
when
sounds
from external
devices
connected
to
this
unit are difficult to
hear
even
after
adjusting
the volume.
The factory default setting is
"MID".
1. Press the
[AJ
button to switch to
the
adjust
mode.
2. Press
the
[I
......J
or
[........Jbutton to
select
"AUX
SENSE".
3.
Turn
the
[ROTARY]
knob
and
select
"AUX
LOW",
"AUX
MID"
or
"AUX
HIGH".
4.
Press
the
[A]
button to return
to
the
previous
mode.
How
to
register/delete
PIN
1.
Press
the
[AJ
button to switch to
the
adjust
mode.
2.
Press the [.......]
or
[........] button
to
select
"CODE
[3".
3.
Press
the
[~IIJ
button.
* When registering: "ETRY 0000" appears.
* When deleting: "DEL 0000" appears.
4.
Press
the
[DIRECTJ buttons
to
input optional
PIN
in
4 digits.
ACAUTION
•
Establish
your
PIN
by
combining
numbers
from
1
to
6 as
you
like
in 4
digits.
Do
not
forget
your
PIN,
for
you
cannot
perform
any
further
operation
without
your
PIN
when
you
remove
the
battery
for
repair,
etc.
• Write
down
your
PIN
for
the
future
use.
5.
Press
and
hold
the
~IIJ
button for 2
seconds
or
longer
to
enter
the PIN.
Notes:
• When registering PIN is completed, the unit enters
the CATS mode.
If
you input wrong number when deleting yourPIN,
you
cannot complete the operation.
In
that case,
the unit requests you
to
input the correct
PIN
6.
Press
the
[AJ
button
to
return to
the
previous
mode
.
Performing
a
system
check
This function verifies the
devices
connect
through
CeNET.
1. Press
the
[AJ
button
to
switch to
the
adjust
mode.
2. Press
the
[.......]
or
[
........
1]
button
to
select
"SYS
CHECK
@".
3.
Press and hold
the
~II]
button for 1
second
or
longer
to start the
system
check.
Triggered
audio
mute
for
cellular
telephones
This
unit requires special wiring to
mute
the
audio
signal
automatically
when
a
cellular
telephone
rings in the car.
* This function
is
not compatible with all cellular
telephones. Contact your local authorized Clarion
dealer for information
on
proper installation and
compatibility.
AUK
function
This
system
has
an external
input
jack
so
you can
listen to
sounds
and
music
from external
devices
connected
to this unit.
26
DFZ675MC