Owner`s manual
Satellite Radio Mode
Listeners
can
subscribe
to
SIRIUS®
Radio
on
the
Web
by
visiting www.sirius.com.
or
by
calling
(888)
539-SIRIUS.
Customers should
have
their
SIRIUS
10
ready (SIRIUS
10
is
located
on
the
SC-C1
SIRIUS
Connect Vehicle Tuner,
solid
separately).
Customers
can
listen
to
music samples
by
tuning
to
channel
184.
Accessing
satellite radio
mode
Press
the
[CONTROL]
knob
or
[SRC
I
<!>]
button on the remote control to switch to the
SAT source.
Displaying the Identification (10) Code
Before you listen to satellite radio, you must
subscribe to the service using
your
radio's
identification number.
To
display
the
radio
10,
use the
[CONTROL]
knob (left)
or
[~]
tuning button on the remote control to tune to
channel
"0". The screen displays the radio
10
where the channel name
is
usually displayed.
Check SC-C1 SIRIUS
Connect
Vehicle Tuner
If
SIRIUS
tuner
is
not
connected,
"NO
TUNER" will appear on the LCD.
Select a
band
Press
the
the
[CONTROL]
knob
(up
long
press) on the panel
or
[BANDfTOP]
button
on
the
remote
control
to
change
between
three
SAT
bands (SR1, SR2 and SR3). Each
band stores up to six preset stations.
Select a
station
Press the
[CONTROL]
knob (left / right) on
the panel
or
[..... ,
~
] buttons on the remote
control to tune to another station.
Preset mode
Six numbered preset buttons on the remote
control
store
and
recall
stations
for
each
band.
Preset scan
Short press the
[SCN/PS/AS]
button on the
remote control to start category scanning.
Long
press
the
[SCN/PS/AS]
button
on
the
remote
control
to
start
preset
station
scanning for 10 seconds each.
Storing
a
station
1.
Select
a
band
(if needed), then select a
station.
2. Press and hold a preset button (numbers
1-6) on the remote control.
3.
The
preset
number
and
station
is
displayed and highlighted.
Recalling a
station
1. Select a band (if needed).
2.
Press
a
remote
control
preset button
(numbers 1-6)
to
select the corresponding
stored station.
Category
and
Channel search
To
access
Category
and
Channel
Search
mode, press the
[CONTROL]
knob (up long
press) on
the
panel
or
[BANDfTOP]
button
on the remote control long press.
1.
Rotate
the
rotary
knob
on
the
panel
to
select the desired category.
2. Press
the
[CONTROL]
knob (left / right)
on the panel
or
[..... ,
~
] buttons on the
remote control
to
select the channel name.
Direct
search
To
access
Direct
Search
mode,
press
the
[CONTROL] knob button on the front panel.
1.
Rotate the
[CONTROL]
knob on the panel
to select the desired direct, and press the
[CONTROL]
knob to confirm the selection.
2.
Rotate
the
[CONTROL]
knob
on
the
panel
or
press
the
[ ... ]
or
[ T ]
button
on the remote control
to
select the direct
name, and press the knob
to
confirm the
selection.
PASSWORD
Refer to System Setup page
9.
LOCK
Refer to System Setup page
9.
UNLOCK
Refer to System Setup page
9.
UNSKIP
Refer to System Setup page 9.
FZ501
12