Installation manual

ManualsBrandsClarion ManualsAutomobile AlarmMS2100

This vehicle security system requires interfacing with several of the vehicle's

factory wiring harnesses. Be sure to verify all connections with a digital multi-meter

prior to making connections. Failure to do this can result in serious damage to the

vehicles electrical system or deploying an air bag(s). It is also highly recommended

that all connections are soldered, rather than the use of T-Taps or Scotch Locks.

MS2100

VEHICLE SECURITY

SYSTEM

Installation Manual

Table of Contents:

1. Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2. After the Installation is Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3. System Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4. Installation Tips and Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

5. Mounting Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6. Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7. Wiring Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

8. Starter Disable Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

9. Plug-in Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

10. Programming Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

11. Arming Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

12. System Programmable Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

13. System Test and Shock Sensor Adjustment . . . . . . . . . . . . . . . . . . . . . 11

14. Parking Light Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

15. Optional Circuit Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

16. Dome Light Supervision Relay Diagram . . . . . . . . . . . . . . . . . . . . . . . . 13

17. Trunk/Hatch Release Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

18. Door Lock Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

19. Driver’s Door Priority Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 20

20. Horn Honk Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

21. Status Indicator (LED) Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

22. Siren Chirp Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

23. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

24. Waranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

25. Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

ms2100.qxd 4/29/2003 3:51 PM Page 1

Summary of content (28 pages)

PAGE 1
ms2100.qxd 4/29/2003 3:51 PM Page 1 MS2100 VEHICLE SECURITY SYSTEM Installation Manual This vehicle security system requires interfacing with several of the vehicle's factory wiring harnesses. Be sure to verify all connections with a digital multi-meter prior to making connections. Failure to do this can result in serious damage to the vehicles electrical system or deploying an air bag(s). It is also highly recommended that all connections are soldered, rather than the use of T-Taps or Scotch Locks.
PAGE 2
ms2100.qxd 4/29/2003 3:51 PM Page 2 1. Before You Begin • Prior to beginning the installation of the Ungo MS2100, be sure that you have completely read and understand this installation manual. • Verify all the vehicle's functions work properly prior to installation (i.e.: power windows, power door locks, climate controls, radio, etc.) • Check with the vehicle’s owner on the location of the status LED and valet switch. • Protect the vehicle by using fender and seat covers.
PAGE 3
ms2100.qxd 4/29/2003 3:51 PM Page 3 4. Installation Tips and Suggestions • Use a digital multi-meter to test all wires; DO NOT use a Test Light. • Check door and trunk pin switches prior to beginning installation. Replace faulty pin switches with either a factory or a high quality replacement pin switch. • Good power and ground connections are essential for proper operation of the security system. Ground the alarm as close to the main unit as possible.
PAGE 4
ms2100.qxd 4/29/2003 3:51 PM Page 4 5. Mounting Components 5.1 Siren 1. Mount the siren in suitable location under the hood that will not interfere with the functionality of the vehicle and away from source of extreme heat (i.e.: exhaust manifold). 2. Make sure the siren cannot be easily accessed from underneath the vehicle or through the grill. 3. Face the siren facing downwards, so water does not accumulate inside the siren housing. 4.
PAGE 5
ms2100.qxd 4/29/2003 3:51 PM Page 5 5.4 Valet/Override Switch Prior to drilling the hole for the valet switch, make sure the switch is well hidden and can't be easily hit. Also, verify there is adequate space behind the valet switch to accommodate for the depth of the switch. 5.5 Status LED Mount the status LED so that it is visible from both sides of the vehicle, if possible. Make sure there is adequate space behind the LED to accommodate for the depth of the LED. 6.
PAGE 6
ms2100.qxd 4/29/2003 3:51 PM Page 6 7. Wiring Information 7.1 Main 12-Pin Harness RED: +12V Battery input. Connect to the vehicle's positive battery terminal and add a fuse within 12 inches. GREEN: (-) Door trigger input. Connect to the wire that shows ground when the door is open.* BLACK: (-) Ground input. Connect this wire to bare metal, using a lock or star washer to prevent the screw from coming loose. If possible, use a factory bolt, rather then a screw. VIOLET: (+) Door trigger input.
PAGE 7
ms2100.qxd 4/29/2003 3:51 PM Page 7 Connect to a relay for an optional feature such as a trunk release solenoid, window module, etc. WHITE: (+/-) Parking light output (10A relay). The output polarity of this circuit can be selected for either (+) positive or (-) negative output via the internal jumper. Make sure to verify the polarity of the parking light circuit before setting the jumper. * Diode isolate the door trigger wires for vehicles with independent door trigger wires. 7.
PAGE 8
ms2100.qxd 4/29/2003 3:51 PM Page 8 10. Programming Remote Transmitters Prior to programming new remote transmitters to the security system, make sure to have the desired transmitters ready. To Enter Remote Transmitter Programming: 1. Turn the ignition ON, OFF, ON, OFF, and leave ON. 2. Press and hold the Valet/Override switch for 5 seconds. The siren will chirp once. 3. Press the Lock button on the transmitter. The siren will chirp once. 4. Press the Lock button on the transmitter again.
PAGE 9
ms2100.qxd 4/29/2003 3:51 PM Page 9 12. System Programmable Parameters Feature Button 1 (default) Button 2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
PAGE 10
ms2100.qxd 4/29/2003 3:51 PM Page 10 7. Ignore Dome Light Delay: Selects whether or not the security system will ignore the door trigger for 20 seconds upon arming. For vehicles with timed dome light delays, the system will not detect a faulty door trigger upon arming. 8. Auto Rearming: Selects whether or not the security system will rearm if no activity is detected after Remote Disarming. (If Passive Door Locking feature was selected during installation, the system will also relock the doors.
PAGE 11
ms2100.qxd 4/29/2003 3:51 PM Page 11 The siren will chirp, indicating that Programming has been entered. 3. Press transmitter button 3. The siren will chirp 6 times indicating the reset signal has been received, and Parameters have been reset to factory default. 13. System Test and Shock Sensor Adjustment 13.1 System Test 1. Verify the Programmable Parameters are set. 2. Verify all wire connections are correct and secure. 3.
PAGE 12
ms2100.qxd 4/29/2003 3:51 PM Page 12 14. Parking Light Jumper Settings The Parking Light Polarity Jumper selects the polarity (+/-) for the output of the on-board Parking Light relay. Negative Positive 15.
PAGE 13
ms2100.qxd 4/29/2003 3:51 PM Page 13 16.
PAGE 14
ms2100.qxd 4/29/2003 3:51 PM Page 14 17.
PAGE 15
ms2100.qxd 4/29/2003 3:51 PM Page 15 18.
PAGE 16
ms2100.
PAGE 17
ms2100.
PAGE 18
ms2100.
PAGE 19
ms2100.
PAGE 20
ms2100.qxd 4/29/2003 3:51 PM Page 20 19.
PAGE 21
ms2100.
PAGE 22
ms2100.
PAGE 23
ms2100.qxd 4/29/2003 3:51 PM Page 23 20.
PAGE 24
ms2100.qxd 4/29/2003 3:51 PM Page 24 21. Status Indicator (LED) Functions LED STATUS FUNCTION Off Slow Flash Rapid Flash Rapid Flash (after disarm) On Solid On Solid (after arming) System is disarmed in Active mode. System is Armed. Passive arming indication and auto rearm. System was triggered. Valet mode. On for 3 seconds, shock sensor trigger has been bypassed. Door or hood/trunk is open. On Solid (when disarmed and not in Valet mode) 22.
PAGE 25
ms2100.qxd 4/29/2003 3:51 PM Page 25 23. Troubleshooting Symptom Probable Cause Suggested Correction Alarm doesn't Arm/Disarm. Alarm in Valet Mode. Ignition input has voltage on it. Missing +12 or ground. Take alarm out of Valet mode. Turn key off and verify yellow wire is connected to correct ignition wire. Check +12V and ground connections. Alarm will not Passively Arm. Passive arming is programmed Off. Wrong door switch polarity. Alarm in Valet mode. Change arming mode to Passive arming.
PAGE 26
ms2100.qxd 4/29/2003 3:51 PM Page 26 Symptom Probable Cause Suggested Correction Dome light supervision does not activate upon Disarm. Relay wired incorrectly. See Dome Light Supervision diagrams. Poor range with the remotes. Antenna wire is grounded; Module is picking up interference from the vehicle's electrical system. Make sure the antenna is not connected to ground. Relocate module or route antenna away from computer modules. Vehicle starts when the alarm is Armed. Wrong starter wire is cut.
PAGE 27
ms2100.qxd 4/29/2003 3:51 PM Page 27 24. Warranty Information This Ungo Security System is warranted against defects in material and workmanship. The main unit and remote controls are covered by this limited lifetime warranty. This Limited Lifetime Warranty applies to Ungo Security systems that have been installed by an authorized Ungo Security dealer. This warranty is to the Original Purchaser ("Owner") and to the original vehicle in which it was installed into.
PAGE 28
ms2100.qxd 4/29/2003 3:51 PM Page 28 25. Wiring Diagram 97-MS2100-00 Rev.