TTX001 TV TUNER OWNER’S MANUAL
INTRODUCTION The Clarion TTX001 is a TV Tuner. It can be integrated into a mobile multimedia system. It has a number of features, including: • Two types of wiring permitted - stand alone or with VMA1131 • Quick tuning to your desired stations • Stereo broadcast reception • Video/audio (stereo) output jacks • Display function when using audio ABOUT THE MANUAL AND WARRANTY To start enjoying your new Clarion TTX001 TV Tuner, please read the instructions listed in this manual.
7. Do not let the unit become hot. If temperature in the car is high or the set has been exposed to direct sunlight and is hot, lower the temperature before using it. DESCRIPTION The Clarion TTX001 TV tuner has a number of exceptional features. For instance, the TTX001 allows two types of wiring: stand alone or with the Clarion VMA1131. It also has preset tuning (for a total of 12 VHF/UHF stations), manual tuning and automatic tuning to permit easy tuning of the desired broadcast stations.
WIRING PRECAUTIONS Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer. 1. Disconnect the negative (-) lead of the battery before making any power connections. 2. When creating passage holes for the power wires, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit. 3.
APPLICATIONS The TTX001 can be operated in a number of applications. Find yours below. With the VMA1131 1. Place tuner into the channel on the back of the monitor and slide the tab into the slot. Mount tuner with the two machine screws supplied. 2. Plug the 16 to 16 pin cable (supplied with the monitor) into the tuner and the back of the monitor. 3. Mount the antenna (ZCB-003 or equivalent) and plug into the antenna input of the tuner. 4.
With the VDH9600, OHM641 and the FM100S 1. Pick a location to mount the tuner. Typically the tuner will be located close to the VCP. Avoid areas with excessive heat or moisture and mount the tuner. 2. Mount the TV antenna (ZCB-003 or equivalent) and plug into the tuner. 3. Plug the 16 pin to A/V out connector into the tuner. Plug the A/V RCA cables, IR extension and power plug into the 16 pin connector and run to the video player. 4. Plug the A/V RCA cable into the A/V input of the player.
Figure 4- TTX001 with OHM641, VDH9600 and FM100S 7
Stand alone with the OHM641 and the WH100 1. Pick a location to mount the tuner. Avoid areas with excessive heat or moisture and mount the tuner. Plug the 16 pin to A/V output connector into the tuner. 2. Mount the TV antenna (ZCB-003 or equivalent) and plug into the tuner. 3. At the OHM641, plug in the video RCA, IR extension and power cables supplied with the OHM641 and run to the tuner. Plug the video RCA and IR extension into the tuner. 4.
REMOTE CONTROL BATTERY INSTALLATION • Insert 2 AAAbatteries into the compartment located on the back of the unit, observing the proper polarity. NOTES: • Each time you change the batteries, you must reprogram the channels. • We suggest you use alkaline batteries; do not use rechargeable batteries. • Always change all the batteries at the same time. Figure 6- Remote Control Battery Installation REMOTE CONTROL OPERATION • To use the remote control, press the Power button to turn on the remote.
TROUBLESHOOTING Before assuming malfunction of the unit, check the following: Problem: No power. Solution: • The fuse may be burned out. Replace the fuse with one of the same rating. • The wiring is incomplete. Check the wire connections and connect them properly. Problem: The picture is unclear. Solution: • The reception condition is poor. This may due to an insufficient signal arriving due to being in the shadow of mountains or buildings. Check again in a location exposed to a stronger signal.
PRODUCT SPECS Power Source Voltage: Power Consumption: Operation Temperature: DC 11-15V 1.5Amax. (1.
661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com TTX001-10 Rev.
