Model S660 ➤Owner’s Guide
limited lifetime consumer warranty This Ungo Pro Security system is warranted against defects in material and workmanship. The main unit is covered by this limited lifetime warranty. This Limited Lifetime Warranty applies to Ungo Pro Security systems that have been installed by an authorized Ungo Pro Security dealer. This warranty is to the Original Purchaser ("Owner") and to the original vehicle in which it was installed into. This warranty is not transferable to any subsequent owner(s) of the product(s).
TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE THE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. Should you have any difficulties with the performance of this product during warranty, please call: 1-800-GO-CLARION or visit your local Ungo Pro Security dealer.
table of contents limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i remote configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LCD 2-way configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 standard 4-button configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 what is included . . . . . . . . . .
code hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 high frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
remote configurations ➜ LCD 2-way configuration 4 5 6 7 8 9 3 2 1 31 30 29 28 10 27 11 26 25 12 24 13 23 14 22 15 21 20 16 17 © 2005 directed electronics, inc.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 4 Vehicle Interior Temperature Indicator Numeric Display AM/PM Indicator Alarm Clock Mode Indicator Timer Function Indicator Transmit Range Indicator Transmission Indication Vibrate/Beep Mode Indicator Power Saver Mode Indicator Remote Start Timer Mode Indicator No Function Vehicle Page Mode Indicator Full Trigger Shock Sensor Indicator Hood/Trunk Open or Trigger Indicator Parking Light Indicator Door Open or Trigger Indic
➜ standard 4-button configuration controls the Arm and Panic On/Off function. controls the Disarm and Panic Off function. controls Silent Mode™ and Auxiliary channel 2 output. no function. and pressed together control channel 4 output. and pressed together control channel 5 output © 2005 directed electronics, inc.
what is included ➤ Control module ➤ ASK transceiver/antenna ➤ One 4-button remote ➤ One 2-way LCD remote ➤ Stinger™ DoubleGuard® 2-stage shock sensor ➤ Revenger™ Soft Chirp™ 6-tone programmable siren ➤ Status LED indicator light ➤ Push-button Valet® switch important information Congratulations on the purchase of your remote alarm system. Due to the complexity of this system, it must be installed by an authorized dealer only.
➜ system maintenance The system requires no specific maintenance other than battery replacement for the remotes. LCD 2-Way Remote Battery Replacement The 2-way remote is powered by a 1.5V AAA battery. The Battery Level indicator has three level indicators that serve as a visual indication of battery charge. When the battery reaches a low charge level that requires replacement, the transceiver will generate a single notification chirp, and the Battery Level indicator will flash continuously.
➜ fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Directed Electronics, Inc. 544 Series Tested to Comply with FCC Standards Directed Electronics, Inc. 477T Series Tested to Comply with FCC Standards Directed Electronics, Inc.
remote functions The remote buttons are used to send commands to the system. The descriptions below reflect the standard configuration for this system. The buttons can be custom configured for the user’s specific needs by the installer. ➜ LCD 2-way remote standard configuration LCD 2-way button configuration Button The System Arm/Lock and Multi-Level Security Arming functions are controlled by pressing this button.
Button When pressed and held this button activates the second unlock or other accessory. and Buttons The numeric display toggles between the time of the day and the alarm clock when these buttons are pressed simultaneously. and Buttons Press these buttons simultaneously to activate the parking timer. Each additional press will toggle through the available options (10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off ).
and Buttons When pressed simultaneously these buttons activate battery saver mode, which will drop power consumption on the transceiver battery to zero when the alarm is inactive or disarmed. ➜ Standard LCD 2-way icon configuration Icon The numeric display icon will show the hours and minutes. Icon The AM/PM icon indicates the time before or after noon. Icon The alarm clock mode icon indicates that the alarm clock mode is active.
Icon The remote transmission indicator icon displays when the transceiver is transmitting a signal. Icon The vibrate/beep mode icon appears when the transceiver is set to vibrate mode. Icon The power saver mode can be turned on or off with the transceiver. This icon displays the status. Icon No function. Icon The vehicle page mode icon displays when the alarm module is paging the transceiver. Icon The full trigger shock sensor icon indicates that the shock sensor has been triggered by a hard shock.
Icon The parking light icon will flash twice when armed or disarmed. The icon also flashes during WarnAway and at the beginning and end of remote start cycles. Icon The door open or trigger icon illuminates when the door trigger has been activated or the door is open, and bypasses that zone until it is closed. Icon No function. Icon The Valet® mode icon appears when the system is in Valet® mode.
optional sensor violation, or a hood/trunk trigger. Icon The arm icon appears when the vehicle is armed and locked. The disarm icon appears when the vehicle is disarmed and unlocked.
Timer Count Down Ending Melody Selection 1** 8 Times*** RS Timer Count Down Mode (on/off )* 9 Times*** Remote Start On Melody Selection 2 10 times*** 5 Selections 1/2/3/4/5 5 Selections 1/2/3/4/5 10 Min Parking Count Down Mode + 1 Time Melody 20 Min Parking Count Down Mode + 2 Times Melody 30 Min Parking Count Down Mode + 3 Times Melody 60 Min Parking Count Down Mode + 4 Times Melody 90 Min Parking Count Down Mode + 5 Times Melody 120 Min Parking Count Down Mode + 6 Times Melo
alarm clock off. The remote will revert to normal operation from the set mode when 15-seconds has elapsed without a button entry. ➜ 4-button remote standard configuration Button The arming is controlled by pressing this button. The panic alarm is triggered by pressing and holding this button. Press this button again to cancel the panic alarm. Button The disarming function is controlled by pressing this button. Button Silent Mode™ and an optional auxiliary function are controlled by this button.
and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. The auxiliary output controls __________________________. and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. The auxiliary output controls __________________________. and Buttons No function.
cation to the user (notifications are audible beeps or the remote vibrates) and the LCD icons will display the current system status. Command Page When a command (arm/disarm, remote start, or auxiliary channel) from the transceiver is sent and received, the system will send a command page back to confirm receipt. Page Recognition Mode The transceiver will leave a zone icon illuminated when it has received a triggered response and will wait for violation recognition.
using your system ➜ warning! safety first The following safety warnings must be observed at all times: ➤ Due to the complexity of this system, installation of this product must only be performed by an authorized Ungo dealer. ➜ active arming You can arm the system by pressing of your remote for one second. When the system arms, you will hear a short siren sound, or chirp, and see the parking lights flash once. If the power door locks are controlled by the system, the doors will also lock.
arming countdown, the status LED will flash twice as fast as it does when the system is armed. At the 20-second point of the countdown, the siren will chirp to indicate that the system is about to arm. At the 30-second point, the parking lights will flash to indicate that the system is armed. note: If any protected entry point (such as a door or a switch-protected trunk or hood) is open, the system will not passively arm (unless forced passive arming is programmed on. See Programming Options section.
➤ The optional starter kill prevents the vehicle’s starter from cranking. ➜ warn away® response description A Warn Away® Response consists of an alarm page along with the responses described below. ➤ ➤ ➤ ➤ Shock Sensor - Light impacts to the vehicle will flash the vehicle lights and chirp the siren for a few seconds. Remote Control Notification - Ten quick beeps (or one vibration).
➤ Door Trigger - If a door is opened the siren will chirp for three seconds, then the siren will sound and the lights will flash for the programmed duration and report Zone 3. The three seconds allow the user time to disarm the system with a minimum of noise should a door be opened inadvertently ➤ ➤ ➤ while the system is armed. Hood Trigger - Opening the hood will sound the siren, flash the lights for the programmed duration, and report Zone 1.
➜ multi-level security arming Multi-Level Security Arming allows you to select which of the system's inputs or sensors will be active and which will be bypassed when the system is armed. (See Table of Zones section of this guide.) Pressing (only in Standard Configuration) again within five seconds of arming the system will activate the Multi-Level Security feature. Each time is pressed again, a different security level is selected.
➜ arming while driving Your security system can be armed while driving the vehicle! Simply press on the remote for two seconds while the vehicle is running. The siren will chirp once to indicate that the security system is armed, and then once more to indicate that the ignition is on. The system will not respond to any input except the door triggers, and the starter kill relay (if installed) will not be activated.
➜ disarming while driving Press on the remote or simply turn off the ignition to disarm the system. The lights will flash twice, the doors will unlock, the siren will chirp twice, and the status LED will turn off. The 2way remote will beep twice (or vibrate). The disarm icon (29) will be displayed on the LCD. ➜ high security disarm This security system offers High Security Disarm.
➜ disarming without a remote If your remote is lost or damaged, you can manually disarm your vehicle security system. To disarm the system without a remote, you must have the vehicle's ignition key and know where the Valet® button is located. Be sure to check with your installer at the time of installation for both the location and the preset response (1-5 presses) of the Valet® button. To disarm the security system, turn the ignition to the ON position.
➜ silent mode To temporarily turn off the arm or disarm chirps, use Silent Mode™. Simply press for less than one second before arming or disarming, and the confirmation chirp(s) will be eliminated for that one operation only. If you want the arm/disarm chirps turned off permanently, your dealer can do this for you. note: The Warn Away® response to lighter impacts is bypassed if the system is armed using Silent Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free.
➜ valet® mode You can prevent your security system from automatically arming and triggering by using Valet® Mode. This is very useful when washing the vehicle or having it serviced. In Valet® Mode, the security system will not arm, even with the remote, but all convenience functions (door locks, trunk release, etc.) will continue to work normally. To enter or exit Valet® Mode: 1. Turn the ignition on. 2. Turn the ignition off. 3. Press and release the Valet® DRW-35 button within 10 seconds.
➜ setting the clock To set the clock press and hold for five seconds, the trans- ceiver will chirp twice and the hour selection will start flashing. Immediately press to advance the hour selection to reverse the hour selection. Once the correct hour is displayed press again and the minute selection will start flashing. Then press to advance the minute selection to reverse the minute selection.
Example If the alarm triggers three times within a 60-minute period and each time the same sensor or switch triggers the alarm, NPC™ will interpret those triggers as false alarms. After the third trigger, NPC™ ignores, or bypasses, that sensor or switch (along with any other sensors or switches sharing the same zone) for 60 minutes. If the bypassed sensor tries to trigger the security system while it is being bypassed, the 60-minute bypass period will start over.
them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. Refer to the System Status Chirps and Table of Zones sections of this guide for diagnostic information. ➜ arming diagnostics If the security system is armed at the same time that an input is active (such as a door opening or sensor triggering), you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification.
bypassed that zone. In either case, the status LED will indicate which zone was involved (see Table of Zones section). The security system will retain this information in its memory and chirp four or five times each time it is disarmed, until the next time that the ignition is turned on. ➜ system status chirps The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system’s status as described below.
➜ table of zones A zone is represented by the number of LED flashes used by the system to identify a particular type of input. Standard input assignments are listed in the following table, along with spaces to write in any optional sensors or switches that have been installed.
note: Your system stores the last two triggered zones in memory. If your system has been triggered but the LED has been reset by turning on the ignition, your dealer can still recall the last two zones that were triggered. Contact your dealer for details. code hopping The receiver and remotes use a mathematical formula called an algorithm to change their code each time the remote is used. This technology has been developed to increase the security of the unit.
high frequency Your system transmits and receives at 434 MHz. This provides a cleaner spectrum with less interference and a more stable signal. Enjoy a phenomenal increase in range, even in areas with high radio interference. owner recognition Owner Recognition is a revolutionary new feature available only from Directed. Using a ProSecurity Programmer, hand-held programming tool, your dealer can program many of the system settings.
rapid resume logic This ProSecurity system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet® Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet® Mode. This applies to all states of the system including arm, disarm, and Valet® Mode.
programming options Programming options control your system's normal, operational set-up. Most options do not require additional parts, but some may require installation labor. The following is a list of the programmable options, with the factory settings in Bold. ➤ Active arming (from remote only) or passive arming (automatic arming 30 seconds after the last door has been closed). ➤ Arming/disarming siren chirps on or off.
arming feature has been programmed on, the system will passively arm after one hour, even if a protected entry has been left open. Forced passive arming ensures that the system will be armed if a door has accidentally been left ajar when leaving the vehicle. note: When the system passively arms after one hour, the entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational.
the Valet® button the programmed number of times. AED is also disabled when the system is in Valet® mode. note: This feature will only function if the FailSafe® Starter Kill relay has been installed. ➤ Siren tones and chirp volume. The output of the Revenger™ Soft Chirp™ siren consists of six different tones in sequence. Any of these tones can be eliminated by a dealer, resulting in a unique, easily identifiable siren sound.
Hood Lock: Prevents the vehicle’s hood from being opened without a key, keeping thieves away from the system’s siren, the battery connections, and other components under the hood. Field Disturbance Sensor: An invisible dome of coverage is estab- lished by installing the 508D “radar” sensor. Your system can react to any intrusions into this field with the full triggered sequence. Power Locks: This system offers lock outputs that can control some manufacturers' power door lock systems.
glossary of terms Control Unit: The “brain” of your system. Usually hidden under- neath the dash area of the vehicle. The control unit houses the microprocessor which monitors your vehicle and controls all system functions. Fault-Proof Starter Interrupt: An automatic switch controlled by your system that prevents the vehicle’s starter from cranking whenever the system is armed.
alarm “goes off ” or “trips.” The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration. Valet® Button: A small push-button switch mounted at a discre- tionary location inside the vehicle. It is used to override the starter interrupt when a remote is lost or damaged, or to enter or exit Valet® Mode. Warning Zone Response: Lighter impacts to the vehicle will generate the Warning Zone response.
✂ Arming ■ QUICK REFERENCE GUIDE To arm, press . When the system arms, you will hear a short chirp, and the parking lights will flash once. Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. Arming while driving ■ To arm the system while driving, press on your remote while the vehicle is running. The system will chirp once and then once more to indicate that the ignition is on. Disarming ■ To disarm, press flash twice. .
Get Started Get Protected Ungo Pro Security 661 W. Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2005 Directed Electronics, Inc.
