Model SR6000 ➤Owner’s Guide
limited lifetime consumer warranty This Ungo Pro Security system is warranted against defects in material and workmanship. The main unit is covered by this limited lifetime warranty. This Limited Lifetime Warranty applies to Ungo Pro Security systems that have been installed by an authorized Ungo Pro Security dealer. This warranty is to the Original Purchaser ("Owner") and to the original vehicle in which it was installed into. This warranty is not transferable to any subsequent owner(s) of the product(s).
TATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE THE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE. Should you have any difficulties with the performance of this product during warranty, please call: 1-800-GO-CLARION or visit your local Ungo Pro Security dealer.
table of contents limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i remote configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LCD 2-way configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 standard 4-button configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 what is included . . . . . . . . . .
safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 starter anti-grind circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 disabling the remote start system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 over and under rev protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 shut down inputs . . . . . . . . . . . . . . . . . .
remote configurations ➜ LCD 2-way configuration 4 5 6 7 8 9 3 2 1 31 30 29 28 10 27 11 26 25 12 24 13 23 14 22 15 21 20 16 17 © 2005 directed electronics, inc.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 4 Vehicle Interior Temperature Indicator Numeric Display AM/PM Indicator Alarm Clock Mode Indicator Timer Function Indicator Transmit Range Indicator Transmission Indication Vibrate/Beep Mode Indicator Power Saver Mode Indicator Remote Start Timer Mode Indicator No Function Vehicle Page Mode Indicator Full Trigger Shock Sensor Indicator Hood/Trunk Open or Trigger Indicator Parking Light Indicator Door Open or Trigger Indic
➜ standard 4-button configuration controls the Arm and Panic On/Off function. controls the Disarm and Panic Off function. controls Silent Mode™ and Auxiliary channel 2 output. controls the Remote Start function. and pressed together control the Timer mode. and pressed together control Turbo/Short Run. and pressed together control channel 4 output. and pressed together control channel 5 output. © 2005 directed electronics, inc.
what is included ➤ Control module ➤ ASK transceiver/antenna ➤ One 4-button remote ➤ One 2-way LCD remote ➤ Stinger™ DoubleGuard® 2-stage shock sensor ➤ Revenger™ Soft Chirp™ 6-tone programmable siren ➤ Status LED indicator light ➤ Push-button Valet® switch ➤ Shut-down toggle switch important information Congratulations on the purchase of your combination remote start alarm system. Due to the complexity of this system, it must be installed by an authorized dealer only.
➜ system maintenance The system requires no specific maintenance other than battery replacement for the remotes. LCD 2-Way Remote Battery Replacement The 2-way remote is powered by a 1.5V AAA battery. The Battery Level indicator has three level indicators that serve as a visual indication of battery charge. When the battery reaches a low charge level that requires replacement, the transceiver will generate a single notification chirp, and the Battery Level indicator will flash continuously.
➜ fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Directed Electronics, Inc. 544 Series Tested to Comply with FCC Standards Directed Electronics, Inc. 477T Series Tested to Comply with FCC Standards Directed Electronics, Inc.
➜ caution This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary the product's intended use. remote functions The remote buttons are used to send commands to the system. The descriptions below reflect the standard configuration for this system. The buttons can be custom configured for the user’s specific needs by the installer.
Button The LCD backlighting will turn on when pressed for less than one second; when held for more than five seconds the transceiver will enter adjustment mode allowing the setting of the clock, timer mode, and audible melody selection. For more information, please refer to the Function Button Configurations section of this guide. Button The remote start function of the system is controlled by pressing this button for one second. To stop the remote start press this button twice.
note: Disarming the system while in temperature auto start mode will cause the system to exit this mode. and Buttons The numeric display toggles between the time of the day and the alarm clock when these buttons are pressed simultaneously. and Buttons Press these buttons simultaneously to activate the parking timer. Each additional press will toggle through the available options (10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off ).
Icon The AM/PM icon indicates the time before or after noon. Icon The alarm clock mode icon indicates that the alarm clock mode is active. Icon The timer function icon flashes during timed functions including parking timer. Icon The transmit range indicator icon stays visible as long as the system is within operating range. Icon The remote transmission indicator icon displays when the transceiver is transmitting a signal.
Icon The VRS mode icon has no function. Icon The vehicle page mode icon displays when the alarm module is paging the transceiver. Icon The full trigger shock sensor icon indicates that the shock sensor has been triggered by a hard shock. and Icons The hood/trunk open or trigger icon illuminates when the hood or trunk trigger has been activated or the hood or trunk is open, and bypasses those zones until it is closed. Icon The parking light icon will flash twice when armed or disarmed.
Icon The Valet® mode icon appears when the system is in Valet® mode. Icon The remote start safety shut down icon indicates the vehicle may be in gear or other unsafe condition inhibiting remote start operation. Icon The battery level icon indicates the level of power remaining in the battery.
Icon Celsius/Fahrenheit icon indicates the current mode of the displayed temperature either in Celsius or Fahrenheit.
Timer Count Down Ending Melody Selection 1** 8 Times*** RS Timer Count Down Mode (on/off )* 9 Times*** Remote Start On Melody Selection 2 10 times*** 5 Selections 1/2/3/4/5 5 Selections 1/2/3/4/5 10 Min Parking Count Down Mode + 1 Time Melody 20 Min Parking Count Down Mode + 2 Times Melody 30 Min Parking Count Down Mode + 3 Times Melody 60 Min Parking Count Down Mode + 4 Times Melody 90 Min Parking Count Down Mode + 5 Times Melody 120 Min Parking Count Down Mode + 6 Times Melo
The remote will revert to normal operation from the set mode when 15-seconds has elapsed without a button entry. ➜ 4-button remote standard configuration Button The arming is controlled by pressing this button. The panic alarm is triggered by pressing and holding this button. Press this button again to cancel the panic alarm. Button The disarming function is controlled by pressing this button. Button Silent Mode™ and an optional auxiliary function are controlled by this button.
and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. The auxiliary output controls __________________________. and Buttons The remote start timer mode is controlled by pressing these buttons simultaneously. and Buttons The short-run turbo mode is activated when these buttons are pressed simultaneously.
Command Page When a command (arm/disarm, remote start, or auxiliary channel) from the transceiver is sent and received, the system will send a command page back to confirm receipt. Page Recognition Mode The transceiver will leave a zone icon illuminated when it has received a triggered response and will wait for violation recognition. Press any button on the transceiver, the LCD information and alarm page alerts will be cleared.
using the installed toggle switch. It is the user's sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED.
performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear. All installations must be performed by an authorized Ungo dealer. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION.
indicates that a security sensor or switch has been bypassed and the system is not monitoring that area (zone) of the vehicle. ➜ passive arming The system can be programmed to arm itself automatically (called passive arming). If the system is programmed for passive arming, it will automatically arm 30 seconds after the ignition is turned off and the system detects that you have left the vehicle by opening and closing a door.
➤ ➤ seconds later, the siren output changes to a continuous blast. This progressive response gives you time to disarm the system with your remote if you inadvertently open the door while the system is armed, while still providing instant response (even if the door is immediately closed). Turning on the ignition key will trip the same progressive response as opening a door. The optional starter kill prevents the vehicle’s starter from cranking.
➜ triggered response description A Triggered Response can be activated by any of the triggers listed below and consists of an alarm page along with the response described for each trigger. The default Triggered Response duration is 30 seconds but can be programmed from 1-180 seconds by your installer with the ProSecurity Programmer. ➤ Sensor Trigger - Heavy impacts to the vehicle will instantly sound the siren and flash the lights for the programmed duration and report Zone 2.
➤ ➤ The zone icons will turn on and remain on until a transceiver button is pressed, clearing the page alert. The transceiver will enter page recognition mode and generate alarm page alerts. note: Icons 13, 14, 16, and 20 represent alarm system triggered sequence zone inputs. For more information about icons and the zones they represent refer to the Standard Remote Configurations section.
➤ Press a fifth time within five seconds: The siren chirps five times followed by a long chirp. All input zones, except the ignition, are now bypassed. note: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed and then re-armed, all the zones will be active again. ➜ arming while driving Your security system can be armed while driving the vehicle! Simply press on the remote for two seconds while the vehicle is running.
➜ disarming To disarm the security system, press . You will hear two chirps, and the parking lights will flash twice. If the power locks are controlled by the system, the doors will also unlock. The siren chirping either four or five times when disarming indicates Tamper Alert, which is described in the Diagnostics Section of this guide. ➜ disarming while driving Press on the remote or simply turn off the ignition to disarm the system.
seconds of the triggered sequence will disarm the security system immediately. The six second timer is provided for your convenience, in case the system is accidentally triggered. ➜ disarming without a remote If your remote is lost or damaged, you can manually disarm your vehicle security system. To disarm the system without a remote, you must have the vehicle's ignition key and know where the Valet® button is located.
➜ silent mode To temporarily turn off the arm or disarm chirps, use Silent Mode™. Simply press for less than one second before arming or disarming, and the confirmation chirp(s) will be eliminated for that one operation only. If you want the arm/disarm chirps turned off permanently, your dealer can do this for you. note: The Warn Away® response to lighter impacts is bypassed if the system is armed using Silent Mode. This ensures that no chirps will be emitted by the siren in an area you want chirp-free.
➜ valet® mode You can prevent your security system from automatically arming and triggering by using Valet® Mode. This is very useful when washing the vehicle or having it serviced. In Valet® Mode, the security system will not arm, even with the remote, but all convenience functions (door locks, trunk release, etc.) will continue to work normally. To enter or exit Valet® Mode: 1. Turn the ignition on. 2. Turn the ignition off. 3. Press and release the Valet® DRW-35 button within 10 seconds.
➜ remote start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control system. If interior heating or cooling is desired, the climate controls must be preset, and the fan blower must be set to the desired level prior to remote starting the vehicle.
5. Once the vehicle has started, it will run for the pre-programmed period of time (either 12, 24, or 60 minutes - see Programming Options section of this guide) or until a shutdown input is triggered. important! It is unsafe to operate a vehicle’s motor in a garage or other closed off area. Breathing the exhaust from the vehicle is hazardous to your health. Never activate the remote start in an enclosed space. When you are ready to drive the vehicle: 1.
unique melody (or vibrate) and the remote start icon (19) will turn off when the remote start shuts down. ➜ valet® take-over The Valet® Take-Over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on. To perform Valet® Take-Over: 1.
➜ short-run/turbo Short run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1, 3, 5 or 10 minutes. This allows the system’s timer to conveniently cool down the turbo after you have left the vehicle. To activate: 1. Park the vehicle and set parking brake. 2. Remove your foot from the brake pedal and leave the engine running. 3. Press and release the and buttons at the same time. 4.
Then press to advance the minute selection or to reverse the minute selection. Once the correct time is displayed simply stop pressing any buttons for 15 seconds and the transceiver will automatically exit the clock mode. ➜ temperature check mode This system will report the interior temperature of your vehicle with the press of three buttons. To activate the temperature display press , and simultaneously and then release.
4. The system will start the car and will run for the specified duration, unless shut down by the remote start button shut down with the remote start button . If the system will remain in timer mode. 5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires. important!! Timer Mode should be used only in open areas. Never start and run the vehicle in an enclosed space such as a garage or carport.
➜ disabling the remote start system This feature allows your system's remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the shutdown toggle switch to the OFF position. The switch can be installed in a location of your choice. Check with your installer for recommended locations.
pedal will shut down the motor at any time during remote start operation, as well as preventing the remote start from activating while it is being pressed. ➜ nuisance prevention circuitry Your system has Directed’s Nuisance Prevention Circuitry™ (NPC™). It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental conditions such as thunder, jackhammers, airport noise, etc.
note: Arming and disarming the system does not reset this function! The only ways to reset a bypassed zone are for it to not trigger for 60 minutes, or to turn on the ignition. If testing your system, it is important to remember that the NPC™ programming can cause zones to be bypassed and appear to stop working. If five chirps are heard when disarming, NPC™ has been engaged. If you wish to clear the NPC™ memory, turn the ignition on. 24-hour timer mode To enter timer mode, press and simultaneously.
➜ arming diagnostics If the security system is armed at the same time that an input is active (such as a door opening or sensor triggering), you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification. A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed, until that input ceases. Three seconds after that input ceases, the security system will resume normal monitoring.
➜ system status chirps The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system’s status as described below.
ZONE (Number of LED Flashes) DEALER-INSTALLED OPTIONS DESCRIPTION 1 Trunk Pin 2 Instant trigger - a heavier impact detected by the shock sensor 3 Door switch trigger 4 Instant trigger - for optional sensors 5 Ignition trigger 6 Hood Pin ➜ interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics. If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the LED.
code hopping The receiver and remotes use a mathematical formula called an algorithm to change their code each time the remote is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep the remote “in sync” with the control unit even if you use the remote control out of range of the vehicle.
owner recognition Owner Recognition is a revolutionary new feature available only from ProSecurity. Using a ProSecurity Programmer, hand-held programming tool, your dealer can program many of the system settings. The programmer makes it possible to program different settings for each remote that is used with the system. Then, whenever a specific remote is used, the system will recall the settings assigned to that remote.
power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet® Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery. Power Saver Mode takes over under the following conditions: ➤ Power Saver when the system is armed: After the system has been armed for 24 hours the LED will flash at half its normal rate, decreasing the system's current draw.
➤ Arming/disarming siren chirps on or off. ➤ The ignition controlled door lock feature on or off: When this feature is programmed on, the doors will lock three seconds after the ignition is turned on, and unlock when the ignition is turned off. If your installer is programming the security system with the ProSecurity Programmer, ignition lock and unlock are independent features that can be programmed separately.
➤ Full trigger response 30 or 60 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance. If your installer is programming the security system with the ProSecurity Programmer, the full ➤ triggered response can be programmed for any duration ranging from 1 to 180 seconds. Automatic Engine Disable (AED) on or off.
➤ The engine can be programmed to run for any duration ranging from 1 to 60 minutes. 12 minutes is the default. After the programmed run time, the engine will shut down and will not restart, unless in Timer Mode. ➤ While the remote start system is running the engine, the parking lights of the vehicle can flash on and off or come on and light steadily. security & convenience expansions Listed below are some of the many expansion options available.
react to any intrusions into this field with the full triggered sequence. Power Locks: This system offers lock outputs that can control some manufacturers' power door lock systems. For other systems, additional parts may be required. Power Trunk Release: The accessory output of the system can op- erate a factory power release for the vehicle’s trunk or hatch. Although the on-board relay can control most power trunk releases, sometimes an optional relay is required.
glossary of terms Control Unit: The “brain” of your system. Usually hidden under- neath the dash area of the vehicle. The control unit houses the microprocessor which monitors your vehicle and controls all system functions. Fault-Proof Starter Interrupt: An automatic switch controlled by your system that prevents the vehicle’s starter from cranking whenever the system is armed.
Trigger or Triggered Sequence: This is what happens when the alarm “goes off ” or “trips.” The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration. Valet® Button: A small push-button switch mounted at a discre- tionary location inside the vehicle. It is used to override the starter interrupt when a remote is lost or damaged, or to enter or exit Valet® Mode.
52 © 2005 directed electronics, inc.
✂ Arming ■ QUICK REFERENCE GUIDE To arm, press . When the system arms, you will hear a short chirp, and the parking lights will flash once. Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. Arming while driving ■ To arm the system while driving, press on your remote while the vehicle is running. The system will chirp once and then once more to indicate that the ignition is on. Disarming ■ To disarm, press flash twice. .
Get Started Get Protected Ungo Pro Security 661 W. Redondo Beach Blvd. Gardena, Ca. 90247 800-GO-CLARION © 2005 Directed Electronics, Inc.
