Ungo ProSecurity
Ungo ProSecurity SAA474U SAA474U K20 RK20 Remote Keyless Entry System Remote Start / Keyless Entry System (2) (2) Anti-Code Anti-Code 4-Button Remote Transmitters (SAA474U) Grabbing Technology Starter Disable Output On-Board Relays for Door Locks and Dome Light Supervision Driver’s Door Priority Unlock Output On-Board Parking Light Flash Relay Hyper Blue LED (2) Auxiliary Outputs Comfort Closure Horn Honk Output 4-Button Remote Transmitters (SAA474U) Grabbing Technology
Ungo ProSecurity SAA474U SAA7101U SAA477U SR7000 SR9000 2-Way Security / Remote Start / Keyless Entry System 1-Mile Range 2-Way Security / Remote Start / Keyless Entry System (1) 2-Way LCD Remote Transmitter (SAA477U) 4-Button Remote Transmitter (SAA474U) Anti-Code Grabbing Technology Compact Satellite Relay Pack for Remote Start with Anti-Grind Circuit Intelli-Tach RPM Detection D2D (Data-to-Data) for XPress Kits Modules Built-in Diesel Wait-to-Start Timer Built-in Turbo Timer Rear
Ungo ProSecurity Ungo Feature Descriptions SDC (Secure Digital Communication) In order to achieve a reliable 1-mile of range from the SR9000, Clarion has implemented Spread Spectrum Technology Secure Digital Communication. Spread Spectrum Technology takes a signal (in the case of the SR9000, a rolling code that tells the system what to do) and spreads the codes over a wide range of frequencies.
Ungo ProSecurity Programmable Override Sequence ProSecurity systems can be programmed to respond to one to five pulses of the Valet/Override switch to disarm the system. Progressive Door Unlock For added security, the ProSecurity system can be configured to unlock the driver’s door only, leaving the remaining doors locked. Pressing the UNLOCK button an additional time will unlock the remaining doors. This option may require additional parts and labor.
Ungo ProSecurity Obtaining Optimal Range Mounting the Extended Range Antenna 1. Clean the mounting area on the windshield with a quality glass cleaner or alcohol to remove any dirt or residue. 2. Plug the receiver/antenna cable into the receiver/antenna. 3. Mount the receiver/antenna vertically using the supplied double-sided tape. 4. Route the receiver/antenna cable to the control module and plug it into the four-pin antenna connector.
Ungo ProSecurity will show between 1V and 6V AC. In multi-coil systems, the system can learn individual coil wires. Individual coil wires in a multi-coil system will register lower amounts of AC voltage. Also, if necessary, the system can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are at the ignition coil, back of the gauge cluster, engine computers, and automatic transmission computers. How to Find a Tachometer Wire with a Multimeter 1.
Ungo ProSecurity system. If the key cylinder itself is pulled out or damaged, it will not generate the resistance code and vehicle will not run. Passkey 3 The Immobilizer uses an antenna ring around the ignition cylinder to energize a small transponder chip hidden in the ignition key. When the ignition is turned on, the chip is energized and the antenna rings sends the code to the Immobilizer control unit. If the code is incorrect the vehicle will not start.
Ungo ProSecurity Transmitter/Receiver Learn Routine Ungo ProSecurity come with either one or two transmitters that have been programmed to the receiver. Use the following learn routine to add transmitters to the system or to change button assignments if desired. The Valet/Override button must be in working order and plugged into the blue port on the Ungo ProSecurity system. There is a basic sequence to remember whenever programming a system: Door, Key, Choose, Transmitter and Release. Procedure: 1.
Ungo ProSecurity RK1: Remote Start/Keyless System Replacement Remote Transmitter: SAA474U Replacement Battery: CR2032 Ch. Number Function 1 Auto-Learn 2 Lock, Panic On / Panic Off 3 Unlock, Panic Off 4 Silent Mode/Channel 2 5 Remote Start 6 Channel 4 7 Turbo Timer / Short Run 8 Timer Mode 9 Lock/Unlock/Panic 10 Panic Only 11 Delete All Remotes RS10: Remote Start/Keyless System Replacement Remote Transmitter: SAA474U Replacement Battery: CR2032 Ch.
Ungo ProSecurity S100/S400: Security/Keyless System Replacement Remote Transmitter: SAA474U Replacement Battery: CR2032 Ch.
Ungo ProSecurity SR1000: Remote Stat/Security/Keyless System Replacement 4-Button Remote Transmitter: SAA474U Replacement Battery: CR2032 Ch.
Ungo ProSecurity SR7000: 2-Way Security/Remote Start/Keyless Entry Replacement 4-Button Remote Transmitter: SAA474U Replacement Battery: CR2032 Replacement LCD Remote Transmitter: SAA477U Replacement Battery: AAA Ch. Number Function 1 Auto-Learn Standard Configuration 2 Delete Remotes: This feature will erase all remotes from the memory of the system. NOTE: Does not reset the programmed features of the system or reset the Intelli-Tach setting.
Ungo ProSecutity Module Programming Routine The Module Programming Routine dictates how the unit operates. Due to the number of steps, they have been broken up into different menus. It is possible to access and change any of the feature settings using the Valet/Override switch. However, this process can be greatly simplified by using the ProSecurity Programmer. Any of the settings can be changed and then assigned to a particular remote, up to four, a feature called individual remote recognition.
Ungo ProSecurity RK1: Remote Start/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. MENU #1 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Active Mode Passive Mode 1 Chirps ON Chirps OFF 2 Ignition Lock ON Ignition Lock OFF 3 Ignition Unlock ON Ignition Unlock OFF 4 Active Locking Passive Locking 5 Panic with Ignition ON Panic with Ignition OFF 6 Door Lock Pulse Duration 0.
Ungo ProSecurity RS10: Remote Start/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Engine Check ON Engine Checking OFF 1 Tachometer Checking Type Voltage Checking Type 2 12 Minutes Run Time (1)* 24 Minutes (2), 60 Minutes (3) Run Time 3 Flashing Parking Light Output Constant Parking Light Output 4 Crank Time 0.6 sec. (1) Crank Time: 0.8 (2), 1.0 (3), 1.
Ungo ProSecurity RK20: Remote Start/Keyless Entry System continued Factory default settings are indicated in bold in the following feature tables. MENU #2 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Intelli-Tach (1) Voltage (2), OFF (3), Tachometer (4) 1 12 Minute Run Time (1) 24 Minutes (2), 60 Minutes (3) Run Time 2 Constant Parking Light Output Flashing Parking Light Output 3 Cranking Time 0.6 sec. (1) Crank Time: 0.8 (2), 1.0 (3), 1.2 (4), 1.
Ungo ProSecurity S660: 2-Way Security/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. MENU #1 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Active Arming Passive Arming 1 Chirps ON Chirps OFF 2 Ignition Door Locks ON Ignition Door Locks OFF 3 Ignition Door Unlocks ON Ignition Door Unlocks OFF 4 Active Locking Only Passive Locking 5 Panic with Ignition ON Panic with Ignition OFF 6 0.
Ungo ProSecurity SR1000: Remote Start/Security/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. MENU #1 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Active Arming Passive Arming 1 Chirps ON Chirps OFF 2 Ignition Locks ON Ignition Locks OFF 3 Ignition Unlock ON Ignition Unlock OFF 4 Active Locking Only Passive Locking 5 Panic With Ignition ON No Panic With Ignition 6 0.8 Second Door Lock Pulse 3.
Ungo ProSecurity SR5000: 2-Way Remote Start/Security/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. MENU #1 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Active Arming Passive Arming 1 Chirps ON Chirps OFF 2 Ignition Door Locks ON Ignition Door Locks OFF 3 Active Locking Only Passive Locking 4 Panic With Ignition ON No Panic With Ignition 5 0.8 Second Door Lock Pulse 3.
Ungo ProSecurity SR6000: Remote Start/Security/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. MENU #1 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Active Arming Passive Arming 1 Chirps ON Chirps OFF 2 Ignition Locks ON Ignition Locks OFF 3 Ignition Unlock ON Ignition Unlock OFF 4 Active Locking Only Passive Locking 5 Panic With Ignition ON No Panic With Ignition 6 0.8 Second Door Lock Pulse 3.
Ungo ProSecurity SR7000: 2-Way Remote Start/Security/Keyless Entry System Factory default settings are indicated in bold in the following feature tables. MENU #1 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Active Arming Passive Arming 1 Chirps ON Chirps OFF 2 Ignition Lock ON Ignition Lock OFF 3 Ignition Unlock ON Ignition Unlock OFF 4 Active Locking Only Passive Locking 5 Panic with Ignition ON No Panic with Ignition ON 6 0.8 Sec.
Ungo ProSecurity SR7000: 2-Way Remote Start/Security/Keyless Entry System (continued) Factory default settings are indicated in bold in the following feature tables. MENU #3 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) Engine Checking: Intelli-Tach Voltage (2), OFF (3), Tachometer (4) 1 Run Time: 12 Minutes (1) Run Time: 24 Min (2), 60 Min. (3) 2 Parking Lights Flashing Parking Lights Constant 3 Crank Time: 0.6 Sec (1) 0.8 (2), 1.0 (3), 1.2 (4), 1.
Ungo ProSecurity SR9000: 2-Way Remote Start/Security/Keyless Entry System (continued) MENU #2 Feature Default LED ON Setting LED OFF Setting Number (Press "LOCK" Button) (Press "UNLOCK" Button) 30-Second Siren Duration 60-Second Siren Duration 1 False Alarm Prevention Circuitry ON False Alarm Prevention Circuitry OFF 2 Progress Door Trigger Instant Door Trigger 3 Override Switch Input: 1 Pulse Override Switch Input: 2-5 Pulses 4 Door Trigger Error Chirp ON Door Trigger Error Chirp OFF 5 Ignition Controlled
Ungo ProSecurity Valet Mode To Enter or Exit Valet mode with the Valet/Override Switch: Procedure: 1. Turn the ignition key ON and then OFF 2. At anytime during the next 10 seconds, press and release the Valet/Override switch. Now the status LED will glow constantly if you have entered Valet mode, and goes out if you have exited Valet mode. To Enter or Exit Valet mode with the remote transmitter: Procedure: 1. Open any door. 2. Press the “LOCK” button on the transmitter. 3.
Ungo ProSecurity Short-Run/Turbo Timer Mode Short run turbo timer mode keeps the engine running after arriving at your destination for a programmed period of 1, 3, 5, or 10 minutes. This allows the system’s timer to conveniently cool down the turbo after you have left the vehicle. Procedure: 1. Park the vehicle and set the parking brake. 2. Remove your foot from the brake pedal and leave the engine running. 3. Press and release the “ ” and “AUX” buttons together at the same time. 4.
Ungo ProSecurity Trouble Shooting Alarm Troubleshooting Shock sensor doesn’t trigger the alarm: Has the false alarm prevention circuitry system been triggered? If so, you will hear 5 chirps when disarming the system. To check this, turn the ignition key ON and OFF to clear the false alarm prevention circuity’s memory, and then retest the shock sensor. Door input does not immediately trigger full alarm. Instead, chirps are heard for the first 3 seconds: That’s how progressive two-stage door input works.
Ungo ProSecurity The vehicle starts, but the starter keeps running: 1. Is the system programmed for engine checking OFF or voltage sense? When programmed for either or these features, the engine cranks for the preprogrammed crank time regardless of how long it takes for the vehicle to actually start. Adjust to a lower cranking time. 2. Was the Tach learn successful? The LED must light solid and bright to indicate a successful learn. 3.
Ungo ProSecurity Wiring Quick Reference K10: Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (-) Parking Light Output White/Blue (-) 200mA Channel 3 Validity Output Black/White (-) 200mA Domelight Supervision Output Green Not Used Blue (-) Second Unlock Output Violet Not Used Black (-) Chassis Ground Yellow (+) Ignition Input Brown (-) Horn Output Red (+) Constant Power Red/White (-) 200mA Channel 2 Auxiliary Output 3-Pin 2-Wire Door Lock Harness Wire Color Fun
Ungo ProSecurity RK1: Remote Start/Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (+/-) Parking Light Output White/Blue (-) Activation Input Black/White (-) 200mA Domelight Supervision Output Green Not Used Blue (-) Second Unlock Output Violet Not Used Black (-) Chassis Ground Brown Red Red/White (-) Horn Output (+) Constant Power (-) 200mA Channel 2 Auxiliary Output 4-Pin Harness Wire Color Lt.
Ungo ProSecurity RS10: Remote Start/Keyless Entry System Main Harness Wire Color Function White (+/-) Parking Light Output Black (-) Chassis Ground Red/White (-) 200mA Channel 2 Auxiliary Output White/Red (+) Activation Input Gray/Black (-) Wait-to-Start Input White/Blue (-) Activation Input Yellow (+) Ignition Output Green/White (-) Factory Alarm Rearm Lt.
Ungo ProSecurity RK20: Remote Start/Keyless Entry System Main Harness Wire Color Function White (+/-) Parking Light Output Black (-) Chassis Ground Red/White (-) 200mA Channel 2 Auxiliary Output Brown (-) Horn Honk Output Orange (-) Ground-When-Locked White/Blue (-) Activation Input Yellow (+) Ignition Output Green/White (-) Factory Alarm Rearm Lt.
Ungo ProSecurity S100: Security/Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (+/-) Parking Light Output White/Blue (-) 200mA Channel 3 Validity Output Black/White (-) 200mA Domelight Supervision Output Green (-) Door Trigger Input Blue (-) Instant Trigger Input Violet (+) Door Trigger Input Black (-) Chassis Ground Yellow (+) Ignition Input Brown (+) Siren Output Red (+) Constant Power Red/White (-) 200mA Channel 2 Auxiliary Output 3-Pin 2-Wire Door Lock Har
Ungo ProSecurity S660: 2-Way Security/Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (+/-) Parking Light Output White/Blue No Function Black/White (-) Domelight Supervision Output Green (-) Door Trigger Input Blue (-) Instant Trigger Input Violet (+) Door Trigger Input Black (-) Chassis Ground Empty Brown (+) Siren Output Red (+) Constant Power Red/White (-) Channel 2 Auxiliary Output 7-Pin Harness Wire Color Empty Empty Empty Empty Empty Yellow Empty 6-Pin Ha
Ungo ProSecurity S670: 2-Way Security/Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (+/-) Parking Light Output White/Blue (-) Channel 3 Auxiliary Output Black/White Domelight Supervision Output Green (-) Door Trigger Input Blue (-) Instant Trigger Input Violet (+) Door Trigger Input Black (-) Chassis Ground Yellow (+) Ignition Input Brown (+) Siren Output Red (+) Constant Power Red/White (-) Channel 2 Auxiliary Output 7-Pin Harness Wire Color Violet Blue/Blac
Ungo ProSecurity SR1000: Remote Start/Security/Keyless Entry System (continued) 5-Pin Harness Wire Color Function Black/White (-) Neutral Safety Input Violet/White Tachometer Input Brown (+) Brake Shutdown Input Gray (-) Hoodpin Shutdown Input Blue/White (-) 200mA Status/Defogger Output 6-Pin Harness Wire Color Lt. Green/Black Gray/Black Green/White Violet/Black White/Black Lt.
Ungo ProSecurity SR5000: 2-Way Remote Start/Security/Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (+/-) Parking Light Output White/Blue (-) Activation Input Black/White (-) Domelight Supervision Output Green (-) Door Trigger Input Blue (-) Instant Trigger Input Violet (+) Door Trigger Input Black (-) Chassis Ground Empty Brown (+) Siren Output Red (+) Constant Power Red/White (-) Channel 2 Auxiliary Output 6-Pin Harness Wire Color Blue Blue/Black Gray Brown
Ungo ProSecurity SR6000, SR7000, SR9000: 2-Way Remote Start/Security/Keyless Entry System Main Harness Wire Color Function Orange Ground When Armed (-) 500mA White (+/-) Parking Light Output White/Blue (-) Activation Input Black/White (-) Domelight Supervision Output Green (-) Door Trigger Input Blue (-) Instant Trigger Input Violet (+) Door Trigger Input Black (-) Chassis Ground Empty Brown (+) Siren Output Red (+) Constant Power Red/White (-) Channel 2 Auxiliary Output 6-Pin Harness Wire Color Lt.
Ungo ProSecurity SR6000, SR7000, SR9000: 2-Way Remote Start/Security/Keyless Entry System 4-Pin Harness on Realy Satellite Wire Color Function Pink (-) 200mA 3rd Ignition Output Violet (-) 200mA 2nd Starter Output Orange (-) 200mA 2nd Accessory Output Blue (-) Status Output 3-Pin 2-Wire Door Lock Harness Wire Color Function Green (-) Lock, (+) Unlock Output Empty Blue (-) Unlock, (+) Lock Output 160
