VMA1891 18.
OWNER’S MANUAL INTRODUCTION: The Clarion VMA1891 is a full-featured 18.1" TFT LCD Color Monitor. It can be used as: • A stand-alone monitor with a home PC or Laptop Computer. • A monitor integrated into a Clarion mobile multimedia system using auxiliary built-in Video Composite (RCA) or S-Video inputs. • A mobile PC monitor through the VGA input. ABOUT THE MANUAL AND WARRANTY: To start enjoying your new Clarion VMA1891, please read the instructions listed in this manual.
VMA1891 18.1” TFT LCD Color Monitor • Do not disassemble or modify the set. Doing so may damage it and voids your warranty. • Keep drinks and drops from umbrellas away from the set. Water may damage the internal circuitry. • Do not let the set become hot. If temperature in the car is high or the set has been exposed to direct sunlight and is hot, lower the temperature before using it. (The liquid crystal panel will work properly within a temperature range of 30 – 113 degrees F.
OWNER’S MANUAL REAR CONTROLS q w e r t AND CONNECTOR LOCATIONS: VGA Input Connector S-Video Input Connector Composite Video Input RS232 Port (Not Available) y DC Input Connector +12Vdc u Power Switch 110Vac 50-60 Hz. i AC Input Connector 110Vac 50-60 Hz. o L/R Audio Input Connectors USB Input Connector OPERATION DESCRIPTIONS: When using this monitor in a 110Vac home environment. Plug the monitor into a 110Vac wall socket with the supplied AC power cable.
VMA1891 18.1” TFT LCD Color Monitor OSD OPERATION DESCRIPTIONS: 1. Press the OSD Menu button 3 to display the on-screen menu. Press the UP 2 or DN 1 button to scroll forward or backwards for each monitor settings. 2. Press the OSD Menu button 3 again to select the function. See list below for individual function operations. 96 OSD Operation OSD FUNCTIONS OPERATIONS: Sub Menus Function Brightness None Intensity of white light. Contrast None Ratio of black to white intensity.
OWNER’S MANUAL OSD FUNCTIONS AND OPERATIONS: Icons Sub Menus Function Auto Adjust 1) All 2) Auto Position 3) Auto Phase 4) Exit Auto Sets all functions Auto Screen Position Auto Phase settings Exits and Auto Saves Input Source 1) RGB Input for PC 2) Video (RCA) Input for Composite Video 3) S-Video Input for High quality video (such as DVD) Use UP/DN buttons to select the appropriate Sub Menu. Press the OSD display button to enter the input type.
VMA1891 18.1” TFT LCD Color Monitor 110 VAC HOME APPLICATION: Attaching a home VCR player. 110V Application 1. Connect the L/R audio outputs of the VCR player to the R-AUDIO-L inputs. 2. Connect the video output to the Video input on the VMA1891. NOTE: Since there is only one set of L/R audio inputs on the VMA1891, additional components must route their audio signals through the VCR A/V inputs. This may limit the components attached to the VMA1891. Attaching a home computer or laptop. 1.
OWNER’S MANUAL NOTE: If there is no S-Video output on your DVD/CD player, connect its video output to the video input on the VMA1891. The S-Video output connection is preferred over the composite video output due to better signal quality. WIRING PRECAUTIONS (+12VDC OPERATION): Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer. • Be sure to disconnect the car’s negative (-) battery terminal to prevent short circuits during installation.
VMA1891 18.1” TFT LCD Color Monitor 12V Application 12VDC APPLICATIONS: (CONT) ABOUT INSTALLATION: Installation of mobile audio and video components requires experience with a variety of mechanical and electrical procedures. Even though this manual provides general application drawings for your new Clarion VMA1891, it does not show the exact installation methods necessary for your particular vehicle.
OWNER’S MANUAL SPECIFICATIONS: Power Requirement: DC Application: +12 volts dc (9-16 volts dc) AC Application: 90-264 V, 50-60 Hz., 1.1-0.6 A Power Consumption: 60 watts, Power On (8-12 W Standby) 5 amps (5000 mA) Weight: 5.4 lb (12 kg) Dimensions: Panel Only: 17-11/16 x 15-3/16 x 3-5/16 in. (449 x 385 x 84 mm) With Stand 17-11/16 x 18-9/16 x 8-7/8 in. (449 x 470 x 225 mm) View Angle: Hor. +70°/-70° Ver. +70°/-40° Tilt Angle of Hinge 10° Forward 40° Backwards Audio Output 3W x 2 Max.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 16 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
