Owner's manual & Installation manual Mode manuel Manual de instrucciones y de instalacion Clarion VRX74SVD AM/FM DVD VIDEO / VIDEO CD / CD / MP3 PLAYER / CD CHANGER CONTROLLER WITH LC DISPLAY r mm AVEC CONTROLADOR DE RADIO DE AM/FM, REPRODUCTOR DE DISCOS DVDNIDEODISCOS CD/CD/MP3/CAMBIADOR DE DISCOS CD CON VISUALIZADOR DE CRISTAL L1QUIDO DE 7" clarion HI?':;' ID3 TAG .
Thank you for purchasing the Clarion VRX745VD. * This owner's manual is for the VRX745VD. ':' Please read this owner's manual in its entirety before operating this equipment. * After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). ':' Check the contents of the enclosed warranty card and keep it carefully with this manual. ';' This manual includes the operating procedures of the CD changer, DVD changer, TV tuner, SIRIUS, 5.1 ch surround decoder.
For your safety, the driver should not watch the TV or operate the controls while driving. Please note that watching and operating the TV while driving are prohibited by law in some countries. Also, while driving, keep the volume to a level at which external sounds can be heard. 1. When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc (DVD/ CD) or the optical parts of the player and proper playback may not be possible.
I Handling Discs Handling Storage • New discs may have some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc. • Do not expose discs to direct sunlight or any heat source. • Do not expose discs to excess humidity or dust. • Do not expose discs to direct heat from heaters.
[voLl [BAND]! [FUNC] ~::--:-- [SENSOR] ~----:--[ISR] "-- [DIRECT] [<~], [~>] With the Front panel open / Avec Ie panneau avant ouvert / Con el panel frontal abierto Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuifjez depfier cette page et vaus reterer aux schemas quand vous fisez chaque chap/Ire. Nota: Cuando lea los capftulos, despliegue esta pagina y consulte los diagramas.
Names of Buttons Note: • Be sure to read this chapter referring to the front diagrams of chapter "3. CONTROLS" on page 5 (unfold). [VOL] button [~/II] • Use this button to increase/decrease the volume. • Press this button to enter the play pause mode in the DVD video mode and changer mode. Press the button again to resume playback. • Press and hold this button for 1 second or longer to mute the sound in the DVD video mode and changer mode.
When the Front panel open [TILT] button • Use this button to adjust the angle of the liquid crystal panel in 5 steps when the liquid crystal panel is open. • When the panel is closed, holding this button depressed for 2 seconds or longer will enable the panel calibration function. [~] button • Use this button to eject a disc.
The Color LCD Display and the Information Panel on the main unit show the following displays, providing information about the mode and functions operated. Information Panel r- Operation status indication *The frequency, play time, clock, etc. are displayed. I MANU: Manual indication g:. : Stereo indication a6JJ : MAGNA BASS-EX indication ALL ~ : ALL indication seN : Scan indication RPT : Repeat indication ROM : Random indication / .11--. IJ Ch ; ; __; r.
Color LCD Display Mode name -Radio mode : FM1 98.1MHz Pch 1 (band/frequency/preset No.) -SIRIUS mode : SR1 100ch Pch 1 (band/channel/preset No.) -DVD changer mode: 02 T02 C002 01 :08:20 (disc No.ltitle No.lchapter No.1 playback time) -DVD video mode : T01 C003 00:08:20 (title No.lchapter No.lplayback time) -Video CD mode : T01 00:01 :18 (track No.lplayback time) -MP-3 mode : F001 T001 00:04:07 (folderNo.ltrack No.lplayback time) -CD mode : T 02 04: 07 (track No.
clarion tJELCDf1E FUNC~ System check The CeNET format utilized on this unit is provided with a system check function. The operation panel's system check menu is displayed under the following conditions: • When power is first turned on after initial installation. • When an external device is connected or disconnected. • When batteries are changed or otherwise when power is disconnected. • When reset button is pressed.
(Radio mode screen) (Next page) (LIST screen) Notes: *1: The operation button is [OPEN] button in the description of operation per mode. *2: External equipment not connected with CeNET is not displayed. *3: The operation key is [SRCH] key in the description of operation per mode. *4: This shows a KEY PAD selection example in the radio mode when 107.9 MHz is selected. *5: Touch the [RTN] key to return to the previous screen. *6: Touch the [T] key to go to the next menu. Touch the [...
(Radio mode screen) Notes: *8: The FUNCTION menu screen displays icons for components connected to the main unit. The icons serve as touch keys for selecting play modes. *9: Pressing the [FUNC] button changes to the following play modes. *10: Screen during DVD mode when automobile is moving. *11: When displaying images in DVD mode, touching the screen surface will cause the menu screen to be displayed.
(Next page) ,,~ .
When a 5.
(AUDIO MODE menu) (AUDIO EXT.
Remote control unit ~ [BAND] Signal transmitter 1(,I-r-w-m-ELE-"'S'-lEw-,aIE~'_C-'Nr-"'CL-Ld-,loperati:~:~:: -~ 30· in all directions [FUNC]~I~I [5 ffic(~ §\\ G I G .-.. \ I Gil [O-9]~~-:-- II ,I DISP [DISC SEL] -~.;.- [SET Up] II II [DISP] [~II] [SEARCH MODE] [MENU] [DVD TITLE] [!][T] [2-Z0NE] [RPT] [RDM] II II 2-Z0NE [SUB TITLE] I I I I a , q ",,)I II [SLOW] I~ V clarion ~~-;.-...-- Inserting the Batteries 1.
Functions of Remote Control Unit Buttons .Shared modes .eve player mode [FUNC] button [BAND] button • Press and hold this button for 1 second or longer to turn on or off the power. Power on/ off, switches among radio, TV, etc. • Press to return to the first chapter in DVD video mode. • Press to return to the first track in CD/MP-3 mode or video CD mode with the PSC function turned off. [VOLUME] button • Increases and decreases volume. [M UTE] button • Turns mute on and off.
Functions of Remote Control Unit Buttons L.A.], [T], [....], [..,] buttons • Press to select menus and other items during DVD video/MP-3 playback. [ENT] button • Press to confirm numerics entered in the KEY PAD operation screen. [< ] buttons • Press to select the next higher or lower chapter number in DVD video mode. • Press to select the next higher or lower track numbers in CD/MP-3 mode or video CD mode with the PSC function turned off. .
8.DGR The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car. Be sure to close the HOLD FLAP for safety when removing the DCP. Removing the DCP 1. Insert the right side of the DCP into the main unit. 2. Insert the left side of the DCP into the main unit. 1. Press the [FUNC] button for 1 second or longer to turn off the power.
9. mAUTIDNS €IN HANDLIN6 Liquid crystal panel/Generalities For a longer service life, be sure to read the following cautions. • Be sure to store the liquid crystal panel inside the main unit when parking the car outdoors for long period of time. The liquid crystal panel will operate properly in a temperature range of o to 60°C. • Do not place anything on the display when the panel is tilted. • Don't allow any liquids on the set from drinks, umbrellas etc. Doing so may damage the internal circuitry.
DVD video is a high-quality digital video source that provides crisp and clear images. One 12 cm disc contains either one film or four hours of music. DVD Video Features This unit provides the following functions in addition to the high image quality and sound quality of DVD video. Notes: • The functions described in the section, "Features", for example, the recorded language, subtitles, angles, etc. differ with the DVD video disc. Refer to the instructions provided with the DVD video.
TV color system Discs This DVD player plays NTSC discs only and cannot be used for playback of SECAM discs and PAL discs. Playable discs This DVD video player can play the following discs. DVD video discs video CDs ~ ffiJD"~@ 'DIGiTAL VIDEO I VIDEO CD TEXT o DI Audio CDs ,About MP3 playback This unit can play back CD-R/CD-RW discs on which MP3 music data have been recorded. For a detailed information, see the page entitled "Listening to an MP3". About the registered marks etc.
11. gPERATICINI Basic Operations Note: Be sure to read this chapter referring to the front diagrams of chapter "3. CONTROLS" on page 5 (unfold). Adjusting the volume When the unit is turned on, starting and stopping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume. Note: • Use this unit after starting the engine. ~ \...?WJ 1.
Basic Operations Opening and turning the liquid crystal panel • To prevent the battery from going dead, operate this unit with the engine running, if possible. • When the liquid crystal panel is operating, be careful not to get your hand or finger caught between the panel and main unit or the instrument panel of the car. • Do not move the liquid crystal panel by hand. Standing up the liquid crystal panel 1. Press the [OPEN] button and the liquid crystal panel comes out and stand up automatically.
Basic Operations Housing the liquid crystal panel 1. Press the [OPEN] button and the liquid crystal panel is housed automatically. Note: • When leaving this unit unused for a long period of time or leaving your car, be sure to house the liquid crystal panel into the main unit.
Basic Operations Adjusting the MID The MID gain, MID frequency (center frequency) and MID Q can be adjusted as follows. 1. Press the [ADJ} button, then touch the [AUDIO} key. 3. Touch the [.,] or [.....] key to adjust to desirable level. * The factory default setting is "0". (Setting range: -6 to 6) 4. Touch the [RTN] key, [ESC] key, or press the [ADJ] button. 2. Touch the [MID} key. 3. When the bass type selection screen is displayed, touch the key for the desirable type to select it. 4. Touch the LA.
Basic Operations • "COLOR": Adjust the color saturation. • This operation is available only when the car is stopped and the parking brake is applied. 4. Operate the touch key to adjust a level. Switching the VTR system between NTSCandPAL * This function is enabled only when the panel is open. * The factory default setting is "NTSC". • "BRIGHT": Switch to the VISUAUVTR in TV mode you use. [~] Press to make image brighter 1. Press the [ADJ] button to switch to the ADJUST MODE menu. 2.
Basic Operations 4. Touch the [RTN] key, [ESC] key, or press the [ADJ] button. 2·Z0NE: 2 (rear monitor lock) 1. Press the [ADJ] button to display the ADJUST MODE menu. 2. Touch the [MONITOR] key. 3. Touch the [REAR MONI LOCK] key and the [ON] key. 5. To cancel the monitor lock, press [ADJ] button, touch the [REAR MONI LOCK] key and the [OFF] key. 6. Touch the [RTN] key, [ESC] key. or press the [ADJ] button. The monitor lock is now canceled.
Basic Operations Clock Adjustment Switching CONNECT(connect) 1. When the panel is open, press the [ADJ] button to select the ADJUST MODE menu. Make the following settings when an external device is connected to the Visual terminal. 2. Touch the [GENERAL] key. NAVI: Touch the [CLOCK] key to adjust the time. 3. Touch the [A], [....], [a.m] or [p.m] key to adjust the time, then touch the [SET] key. * The time is displayed in 12-hour format. 4. Touch the [RTN] key, [ESC] key, or press the [ADJ] button.
Radio Operations FM reception For enhanced FM performance the mRIiI:rUNEC:= ® tuner includes signal actuated stereo control, Enhanced Multi AGe, Impulse noise reduction curcuits and Multipath noise reduction circuits. Listening to the radio 1. Touch the [SRCH] key to switch the KEY PAD. 2. Touch the [0]-[9] key corresponding with the frequency you desired. When you touch the wrong number ([0]-[9] key), you can cancel that to touch the [CLR] key. 3. Touch the [ENT] key.
Radio Operations • Using the LIST screen 1. Touch the [LIST] key. 1. Press the [BAND] button and select the desired band. (FM or AM) 2. Touch the [LIST] key. 3. Touch and hold the [AS] key for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels. Preset scan 2. Touch the corresponding [DIRECT] key to recall the stored station. * You can select the desired band to touch the [BAND] key.
DVD Video Player Operations Changing DVD System Settings Notes: • If the SETUP operation is performed in the middle of video COIOVO video play, the disc plays from the beginning. • Various settings of the SETUP menu cannot be made with the remote control unit. .When watching through a conventional type of the rear view monitor (4:3) • N PS : The leftmost and rightmost areas of the screen are cut off. Selecting the DVD SETUP menu 1. Touch the screen to show the menu screen. 2.
DVD Video Player Operations 2. Touch the key to select a desired language to set it. * The factory default setting is "ENGLISH". 3. Touch the [RTN] key ([ESC] key). Setting up the audio language 1. Following the steps 1 to 3 in "Selecting the DVD SETUP menu", touch the [AUDIO LANGUAGE] key. 2. Touch the key to select a desired language to set it. * The factory default setting is "ENGLISH". 3. Touch the [RTN] key ([ESC] key). Setting up the subtitle language 1.
DVD Video Player Operations The relationship between DVD video category codes and parental level are shown in the table below. Use this table when setting the parental level. LEVEL7 NC-17 (NO ONE 17 AND UNDER ADMITIED) LEVEL6 LEVEL4 R (RESTRICTED) PG-13 (PARENTS STRONGLY CAUTIONED) LEVEL3 PG (PARENTAL GUIDANCE SUGGESTED) LEVEL1 Basic Operations Loading a disc Insert a disc into the centre of the insertion slot with the label side facing up. The disc plays automatically after loading.
DVD Video Player Operations Ejecting a disc 1. Press the [~] button a disc ejects. "EJECT" appears in the display. The play mode then switches to Radio. * If a disc is left in the ejected position for 15 seconds, the disc is automatically reloaded (Auto reload). In this case, however, the play mode will remain set to Radio. Note: • If you force a disc into before auto reloading, this can damage the disc. 4.
DVD Video Player Operations Fast forward and fast backward Slow playback [~/II] button or touch the [~/II] key, then press and hold the [~>] button or the [~~] key. While the button or key is 1. Press the being pressed, slow playback continues at the speed 1/3 times the normal playback. • Slow playback cannot be performed in the backward direction. In addition, audio cannot be reproduced during slow playback. 1. Press and hold the [<....] or [~>] button during playback.
DVD Video Player Operations Scan playback Switching among languages Scans and plays back all chapters recorded on the DVD-Video, the first 10 seconds for each. On discs in which two or more audios or audio languages have been recorded, you can switch among the audio languages during playback. 1. Touch the screen to display the menu, then touch the [SUB] key. 2. Touch the [SCAN] key, then touch the [RTN] key. The message "C.SCN" will be displayed.
DVD Video Player Operations Switching angles Watching a video CD On DVD discs in which video images have been recorded in two or more angles, you can switch among the angles during playback. After disc loading, the play mode is automatically engaged. This operation can be performed when the "Setting up the angle mark display" function (see P. 32) is set to "ON". 1. Touch the screen. 2. Touch the playback. [9] (Angle mark) key during Each time you touch the key, you can switch among angles.
DVD Video Player Operations Slow playback Fast forward and fast backward 1. Press the [../11] button then press and hold the [...> ] button. 1. Press and hold the [<....] or [...> ] button during playback. While the button is being pressed, slow playback continues at the speed 1/3 times the normal playback. • Slow playback cannot be performed in the backward direction. In addition, audio cannot be reproduced during slow playback.
DVD Video Player Operations Displaying the playback status Skipping a track (searching) 1. Touch the screen to display the menu, then touch the [SUB] key. 1. Press the [<1II1II] or [1iI->] button during playback. 2. Touch the [P.TIME] key. Playback status is displayed on the screen. Tracks are skipped, as many as the times the button is pressed, and playback starts. 3. Touch the screen to turn off the display. The display will turn off after 7 seconds.
DVD Video Player Operations Selecting a track on the LIST screen This function allows you to select tracks from a displayed list. Note: • The scan playback function can also be performed using the title list screen's {T.SCN] key. To cancel play, touch the {T.SCN] key once again. 1. Touch the [LIST] key. Displaying CD titles The list menu will appear. 2. Press the [...] or [T] button to change the track display. This unit can display title data for CD-text CDs.
DVD Video Player Operations • Logical format (File system) Pausing playback 1. When writing an MP3 file on a CD-R disc, please select "1509660 level 1 or level 2 (without including expansion format)" as the writing software format. Normal playback may not be possible if the disc is recorded on another format. 1. Press the [~/II] button or touch the [~/II] key during playback. Playback pauses. 2. To resume playback, press the [~/II] button or touch the [~/II] key again, and playback resumes. 2.
DVD Video Player Operations 3. Touch the [...] or [T] key to select the track and touch the track name. * When the selected track's ",)" mark is touched, the titles will scroll. Touch the [RTN] key to return to the folder select (LIST) screen. 4. Touch the [ESC] key. Playback by selecting a folder and track (Direct select mode) This operation allows searching using the folder and track numbers recorded on the MP3 disc.
VISUAL Operations CD Changer Operations This function is available when a VTR, etc. is connected to the visual terminal. Note: • When an optional DVD (CD) changer is connected through the CeNET cable, this unit controls all DVD (CD) changer functions. This unit can control a total of 2 changers (CD and/or DVD). For your safety, the driver should not watch the VTR, etc. or operate the controls while driving. Please note that watching and operating the VTR, etc.
CD Changer Operations When the panel is open: Selecting with a track number 1. Touch the [DISC], [TRACK], [ARTIST], or [USER] key to select the desired title. The selected titles except for the user title scroll once. Selecting a CD When the panel is closed: Each of the [DIRECT] buttons corresponds to a disc loaded into the magazine. • Selecting a disc from 1 to 6 Press the corresponding [DIRECT] button (1 to 6) to select the desired disc. .
CD Changer Operations TOP function The TOP function plays from the first track (track No.1) of the disc. • When playing a disc 1 to 6 Press the [DIRECT] button (1 to 6) with the same number as the CD playing . * DISC [RANDOM]; disc random playback The disc random play selects and plays individual tracks or discs automatically in no particular order. 3. Touch the [RTN] key, return to the previous screen. • When playing a disc 7 to 12 (only when a 12 disc CD changer is used.
DVD Changer Operations Only basic operations of DVD changer can be performed from the unit. Use the remote control unit to perform the following functions. • SCAN, REPEAT, RANDOM function TV Operations TV functions When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions. To watch TV requires a TV tuner.
TV Operations Seek tuning .Step tuning: 1. Press the [BAND] button and select the desired TV band (TV1 or TV2). * The same operation can be performed by touching the screen to display the menu screen, then touching the [BAND] key. * If "MANU" is lit in the display, press and hold the [BAND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available. Press the [~>] or [<.....] button to manually tune in a station. Notes: 2. Press the [-">1 or [<....
TV Operations SIRIUS Operation 2. Touch the screen to display the menu, then touch the {LIST] key. What is Sirius Satellite Radio? 3. Touch and hold one of the [DIRECT] key for 2 seconds or longer to store the current station into the preset memory. Auto store Auto store selects 6 TV stations automatically and stores each one into a preset memory. If there are not 6 stations with good reception, stations previously stored in memory remain and only the strong stations are stored into memory. 1.
SIRIUS Operation Selecting a band Selecting with a station number Press the [BAND] button to select a band. Each press of the button changes the display as shown below. 1. Touch the [SRCH] key. SR1 ~ SR2 ~ SR3 ~ SR1 ... • Information displayed during reception The following information is displayed when Sirius Radio cannot be received normally.
SIRIUS Operation * This changes the seek mode to manual mode and the "MANU" indicator on the display lights. When this operation is performed in manual mode, the seek mode is engaged and the "MANU" indicator on the display goes off. Note: .. The receiver automatically reverts to the seek mode when the r<~J or button is not used for 7 seconds in the manual mode. 2. Press the [<] button. The receiver moves to channels above or below the current channel one by one.
SIRIUS Operation Other Functions Presetting a category Entering titles A category can be preset by registering specific categories in [DIRECT] keys 1 to 6. Then the desired category can be recalled by pressing the corresponding [DIRECT] keys. Titles up to 10 characters long can be stored in memory and displayed for Radio stations, CD, TV stations and CD changer. The numbers of titles that can be entered for each mode are as follows. 1. Touch the [SUB] key. 2.
Other Functions Title list play • "F. WIDE": (full wide mode) You can display a list of titles, then select the CD track, disc or broadcast station to listen to from that list. The whole image elongates horizontally. * You can not display a title list with the unit in Seek, Preset Scan, Auto store (Tuner or TV) mode. Cancel those operation modes before to display a title list. 1. Touch the screen (TV mode only). 2. Touch the [LIST] key to display the LIST screen.
5. 1 ch Surround Decoder Operations 5.1 ch Surround Decoder control function This function is available when a 5.1 ch Surround Decoder (DVH940) is connected. When the 5.1 ch Surround Decoder (DVH940, sold separately) is CeNET connected, the 5.1 ch Surround Decoder Control unit (DVC940, sold separately) cannot be used. This section describes operation procedures only. For other details, refer to the owner's manual supplied with the 5.1 ch Surround Decoder.
5. 1 ch Surround Decoder Operations .SPEAKER GAIN DSFmode This function sets speaker output level. * This function is not available for speakers whose SPEAKER SEL setting is set to OFF. DSF effect ON/OFF * The factory default setting is "OFF". 3-1. Touch the [SPEAKER GAIN] key to show the submenu. 1. Press the [ADJ] button and touch the [AUDIO] key. 3-2. Touch the [FRONT L], [CENTER], [FRONT R], [SURROUND R], [SURROUND L] or [SUB WOOFER] key to set respective item. 3-3.
5. 1 ch Surround Decoder Operations Setting and storing P.EQ Properties 1. Press the [ADJ] button and touch the [AUDIO] key. 2. Touch the [P.EO] key to show the PEQ adjusting display. 3. Touch the key for the desirable type to select it. The REQ adjustment contents are as follows: .SIGNAL * The factory default setting is "P.NOISE". This function selects "P. NOISE" or "MUSIC". .SPEAKER SELECT * The factory default setting is "FRONT". This function selects "FRONT", "CENTER" or "SURROUND". .
Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. The microprocessor has malfunctioned due to noise, etc. Turn off the power and remove the DCP. Press the reset button for about 2 seconds with a thin rod. Note: When the reset button is pressed, turn off the ACC power. (SECURITY 11 pv ~ 0 The Reset button :I: Disc cannot play with the display "PARENTAL VIOLATION" shown.
The brightness control is too low. Adjust the brightness properly. The operating condition is not good. The temperature inside the vehicle may be O°C or Jess. Set to an appropriate temperature (25°C or so) and check it again. The headlight of the vehicle is lit. The display is made dark at night to prevent the glare (When the headlight of the vehicle is lit in the daytime, the display gets dark). The color is not adj usted adequately. Check that COL and HUE are adjusted properly.
13. ERROR DIIRLAYI If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. A CD is caught inside the CD deck and is not ejected. This is a failure of CD deck's mechanism and consult your store of purchase. A CD cannot be played due to scratches, etc. Replace with a non-scratched, non-warped-disc. A CD is loaded upside-down inside the CD Eject the disc then reload it properly. deck and does not play. A PAL format disc has been loaded.
14. IPEmIFIEATI.NS FM Tuner LCD Monitor Frequency Range: 87.9 MHz to 107.
VRX74SVD Installation and Wire connection manual • Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. BEFORE STARTING PACKAGE CONTENTS GENERAL CAUTIONS CAUTIONS ON INSTALLATION INSTALLING THE MAIN UNIT REMOVING THE MAIN UNIT CAUTIONS ON WIRING WIRE CONNECTION SAMPLE SYSTEMS '" 61 61 62 62 63 65 65 66 69 -1. BEFORE STARTING 1. This set is exclusively for use in cars with a negative ground 12 V power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery "8" terminal before starting.
-3. GENERAL CAUTIONS 1. bo not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service centre. 2. Use a soft, dry cloth to clean the case. Never use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently. -4. CAUTIONS ON INSTALLATION 1.
-5. INSTALLING THE MAIN UNIT • Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose. 3.
• Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (*). (Figure 8) If the vehicle is not equipped with a factoryinstalled radio, obtain an installation kit to install the main unit in the following procedure. 1. Remove the screws from both side of the main unit.
-6. REMOVING THE MAIN UNIT 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and the universal mounting bracket, fit tab ® of the spring into hole ® of the hook plate, then Note: Keep the hook plate.
-8. WIRE CONNECTION -F Radio antenna jack Optical output connector ~ '---@-O-----lII-------l@.l-mill]J 1[~....~....f..e~~~: . .... .I.................... ~.-.-.-.-.-,-,-.-.- •• Red 1~~G~ra~y~~~ White Right} Front audio output terminal (*2) left 1~~8~la~Ck~R:e~d~Ri9ht left fli } Rear au d" 10 . ( output terminal *2) White Red Right } Non fader output terminal left Yelow ...---..utJL...j""l Video output terminal (*3) ...---...wL...j""l TV tuner input terminal ...----.uuL...
Yellow +12V main power Black Ground "-::====:::=====~p~u~rp~l:e/~B~la:ck Purple Rear right Rear right EB e .I_I_.~ i i i i ::.._._.
• Connecting the Accessories • Connection to the external amplifier The external amplifier can be connected unless the 5.1 ch Surround Decoder is connected. For detailed information, refer to the instruction manual of the 5.1 ch Surround Decoder. • Connection to the CCO camera for vehicle The CCD camera for vehicle can be connected to CCD terminal on the tuner amp unit. For detailed information, refer to the instruction sheet or manual for the CCD camera.
-9. SAMPLE SYSTEMS • Sample System 1 VRX745VD ~ o RCAcable (sold separately) Front Speakers Visual input \ Rear View Monitor (VMA5894/ VMAl194) CeNETcable (Included the TV tuner) RCA video cable (included the TV tuner) JJ () ~ TV tuner (TTX7501z) SIRIUS tuner ~ CCO I (~;;;~;) » < 0: CD o (') ~ 0> 0- ro ~ Conector cable (included the CC425E) CeNET cable (included the SIRIUS tuner) S' ;:======tD3::::±::J (') C- o.. CD 0..
• Sample System 2 VRX745VD Front Speakers RCA video cable (included the TV tuner) :IJ RCA cable (sold separately) () » Rear Speakers 4-Channel Amplifier < 0: (l) o () ll.l 0- ro (APA4320) S· () C- RCA cable (sold separately) o.. (l) 0.. ~ I0 I p=;(IIl(!]J[]P ~ Center speaker built-in amplifier (SRKS) r-----.......
Clarion Co., Ltd. All Rights Reserved. Copyright © 2004: Clarion Co., Ltd.
~ CAUTION With the screen open, a driver may not see the disc insertion slot. For your safety, insert a disc with the screen closed. F'ran~ais ~ PRECAUTION Lorsque Ilecran est ouvert, il est possible que Ie conducteur ne voie pas la fente d'insertion du disque. Pour votre securite inserez Ie disque avec I'ecran ferme. ~ PRECAUCION Con la pantalla abierta, es posible que el conductor no pueda ver la ranura de inserci6n del disco. Para su seguridad, inserte el disco con la pantalla cerrada.
WEL ME T 100 CHANNELS OF THE BEST ENTERTAINMENT ON THE ROAD siriusradio.
~II1IUS~~~~~~~- "'DJ~ 1 2 3 4 5 7 8 9 15 17 20 21 22 23 24 25 26 27 29 • Top 40 Hits Adult Contemporary Alt Pop Mix Love Songs The Best of the 50s/60s The Best of the 70s The Best of the 80s The Best of the 90s Soft Rock Eclectic Rock Rock Hits Modern Rock Mainstream Rock Classic Rock I Classic Rock 11 Classic Alternative Alternative I Alternative 11 Hard Rock :D 2002 Sirius Satellite Radio Inc.
GET READY FOR 100 CHANNELS OF THE BEST IN-CAR ENTERTAINMENT. You've just purchased a Sirius Satellite Radio receiver that's going to plug you into 60 original music channels, from today's hits to R&B oldies to classical masterpieces. From authentic country and real bluegrass to cool jazz, hot latin, reggae and rock. Plus 40 channels of world-class sports, news and entertainment, like ESPN, Radio Disney, E! Entertainment Radio, CNBC, Fox News and Discovery Radio. EXPERIENCE SIRIUS IN TWO SIMPLE STEPS.
281-0624-00 2002/4 (A) clarion LIMITED WARRANTY INFORMATION For USA and Canada only This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase. Clarion ProAudio products, except for speakers, are covered by a two year limited warranty when installed by an authorized Clarion dealer.
