Owner`s manual
11. gPERATICINI
Adjusting
the volume
1.
Operate
the
[VOL]
button in
the
direction
of
the
+ (up)
or
- (down) to
adjust
the
volume;
+ :
Increases
the
volume.
- :
Decreases
the
volume.
*The volume level indicated in the display is
in
a
range from
0 (minimum) to 33 (maximum).
Note:
Be sure to read this chapter referring to the front diagrams
of
chapter
"3.
CONTROLS" on page 5 (unfold).
Basic Operations
When
the
unit
is
turned
on,
starting
and
stopping
the
engine
with
its
volume
raised
to
the maximum
level may
harm
your
hearings. Be careful
about
adjusting
the volume.
Note:
• Use this unit afterstarting the engine.
~
EngineON
\...?WJ
position
MAIN
Display
While
driving,
keep
the
volume
at
a level at
which
external
sounds
can be heard.
Flf'j
tOng'"'"
:3
)
,--
,--,
,-'"
"h
- )
i i
ii--i'
j
..........
_
...
,
.-
.
::1
L:i·
,::
•
ClockTime Display
•
MAIN
Display
•
SUB
Display
Notes:
• Once selected, the preferred display becomes the
default display. When
a function adjustment such
as volume is made, the display momentarify
switches to that function's display, then returns
back to the preferred display several seconds
after the adjustment.
•
If
a title has been input,
it
is shown in the SUB
display.
If
no title has been input, "NO TITLE"
appears in the display.
To
input a title, refer
to
the
subsection
"Entering
titles"
in
"Other
Functions"
section.
• For CD
and
TV,
some special characters
of
the
title
will not be displayed on the Information Panel
of
the
DCP.
In this case, those characters will only
be left blank.
• SUB displays do not
appear
when panel is open.
VRX745VD 23
Switching
the
display
When
the
panel
is
closed:
1.
Press
the
[DISP]
button
to
select
the
desired
display.
Each
time
you
press
the
[DISP] button,
the
display
switches
in
the
following order:
Turning on
and
off
the
power
Note:
• Be careful about using this unit for a long time
without running the engine.
If
you drain the car's
battery too
far,
you may
not
be able to start the
engine
and
this can reduce the service life
of
the
battery.
1.
Press
the
[FUNC]
button.
2.
The
illumination
and
display
on
the
unit light
up.
The
unit
automatically
remembers
its last
operation
mode
and
will
automatically
switch
to
display
that
mode.
3.
Press
and
hold
the
[FUNC]
button
for
1
second
or
longer
to
turn
off
the
power
for
the
unit.
Note:
• About the "SYSTEM CHECK"
The confirmation
of
connected equipment must
be
performed for this unit only when the wiring
connection is complete
and
power
is turned on to
the unit first. When the
power
is supplied, "PUSH
PWR"appear in the display. Press the
[FUNCj
button, the system check starts inside the unit.
When "COMPLETE"
and
"PUSH PWR" appear
alternately, press once again the
[FUNCj
button.
Selecting a mode
1.
Press
the
[FUNC]
button
to
change
the
mode
of
operation.
2.
Each
time
you
press
the
[FUNC]
button, the
mode
of
operation
changes
in
the
following
order:
Radio
mode
~
SIRIUS
mode
~
DVD
mode
~
CD
changer
mode
~
DVD
changer
mode
~
TV
mode
~
VISUAL
mode
~
Radio
mode
...
* External equipment not connected with
CeNET is not selected.