Owner`s manual
Basic
Operations
Housing
the
liquid
crystal
panel
1.
Press
the
[OPEN] button and the liquid
crystal panel is housed automatically.
Note:
• When leaving this unit unused for
a long period
of
time
or
leaving your
car,
be sure
to
house the
liquid crystal panel into the main unit.
Turning the
liquid
crystal
panel
horizontal
(Air
conditioner
operation mode)
When the
way
the liquid crystal panel is
mounted hinders
the
operation of the air
conditioner,
the
position of the panel can be
turned horizontal temporarily.
1.
Press and hold the [OPEN] button when the
liquid crystal panel is upright, and release the
button when a beep is heard.
2. The liquid crystal panel turns horizontal.
'"
Press the [OPEN] button again when the
liquid crystal panel is
in
the horizontal position,
and the panel returns
to
the original position.
"'
The unit can also be set so that the panel
returns to its original angle after a set time
in
the horizontal position (See P.29).
Mute
1. When
in
the radio, SIRIUS,
VISUAL
or
TV
mode, each time you press the [MUTE]
button, mute is turned on and off. "MUTE"
appears when mute is turned on.
2. In modes
other
than radio, SIRIUS, VISUAL,
or
TV,
enable
the
MUTE function by holding
the [MUTE] button depressed
for
1 second
or
longer.
Regarding the
menu
screen's [RTN]
and
[ESC] keys
• [RTN]: Touch the [RTN] key to return to the
previous screen.
• [ESC]: Touch the [ESC] key to return to the
main screen.
In the
ADJUST
MODE, pressing the
[ADJ]
button will also cause a return to the main
screen.
In cases
where
this kind of multiple key
response is supported, the following kind of
notation will be used:
Touch the [RTN] key, [ESC]
key,
or
press the
[ADJ]
button.
Adjusting
the AUDIO
Note:
• When the separately-sold
5.
1 ch Surround
Decoder (DVH940j is used, the bass and treble
tone adjustments cannot be made.
To
adjust the
tone, refer
to
the section "5-1
ch
Surround
Decorder
Operations".
Adjusting
the balance/fader
1. Press the
[ADJ]
button, then touch the
[AUDIO]
key.
2. Touch the
[BAL/FAD]
key.
3. Touch the [....]
or
[T]
key to adjust to the
fader level.
*The factory default setting
is
"0". (Adjustment
range: front 13 to rear 13)
[....]
key:
Emphasized the sound from the
front speakers.
[T]
key: Emphasized the sound from the
rear speakers.
4. Touch the [
.....
]
or
[.-.]
key to adjust to the
balance level.
*The factory default setting is "0", (Adjustment
range: left 12 to right 12)
[
.....
] key : Emphasized the sound from the left
speakers.
[.-.]
key:
Emphasized the sound from the
right speakers.
5.
Touch the [RTN]
key,
[ESC]
key,
or
press the
[ADJ]
button.
Adjusting
the BASS
The bass gain, bass frequency (center frequency)
and bass
Q can be adjusted as follows.
1.
Press the
[ADJ]
button, then touch the
[AUDIO] key.
2. Touch the
[BASS]
key.
3.
When the bass type selection screen is
displayed, touch the key
for
the desirable
type to select it.
4. Touch the [....] or
[T]
key to adjust to
desirable level.
GAIN :
-6
to 8 (The factory default setting
is "0")
FREQ. : 50Hz/80Hz/120Hz (The factory
default setting is "50")
Q : 1/1.25/1.5/2 (The factory default
setting is
"1
")
5. Touch the [RTN] key, [ESC]
key,
or
press the
[ADJ]
button.
VRX745VD
25