Owner’s manual & Installation manual Mode d’emploi et manuel d’installation Benutzerhandbuch & Installationshandbuch Manuale dell’utente e manuale di installazione Gebruikershandleiding en installatiehandleiding Manual de instrucciones y de instalación Ägar- & installationshandbok Manual do utilizador e manual de instalação Betjeningsvejledning og installationsvejledning VRX878RVD DVD MULTIMEDIA STATION WITH CeNET & 7-inch TOUCH PANEL CONTROL STATION MULTIMEDIA DVD AVEC COMMANDE PAR ECRAN TACTILE 7 pouces
CAUTIONS: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT”. To use this model properly, read this Owner’s Manual carefully and keep this manual for your future reference. In case of any trouble with this player, please contact your nearest “AUTHORIZED service station”. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Turning the power on ∗1 When the liquid crystal panel is open System check The CeNET format utilized on this unit is provided with a system check function. The system check function is performed under the following conditions: •When power is first turned on after initial installation. •When an external device is connected or disconnected. •When Reset button is pressed. ∗In addition to the above conditions, the system check function can be performed from the GENERAL menu in the ADJUST or ∗2 mode. 1.
[VOICE] [MAP] Deutsch [MENU] Italiano [ ] Nederlands [TA] [SRC] [MONI] Sensor [BAND] [ADJ] Español Svenska Português Dansk : Be sure to unfold this page and refer to the front diagrams as you read each chapter. *The control panel can be detached to prevent theft. For details, see the pages entitled “DCP (Detachable Control Panel)”. Remarque : Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
English Outline of Button and Touchkey Operation TUNER mode operation Owner’s manual (Source menu) (Option Menu) (Preset List screen) (PTY Preset List screen) • Selects desired station. (PTY Item List screen) Note: ∗1:These images indicate the buttons to press or keys to touch. ∗2:External equipment not connected with CeNET is not displayed.
English Outline of Button and Touchkey Operation DVD Video mode operation Owner’s manual (DVD PLAYER mode screen)∗3 (Source menu) ∗Screen during DVD mode when motorcar moving. (Option menu) (DVD SETUP menu) Note: ∗3:When displaying movies in DVD video mode, touching the screen surface will cause the DVD PLAYER mode screen to be displayed.
English Outline of Button and Touchkey Operation Adjusting audio feature settings ●When no surround decoder is connected Owner’s manual (ADJUST mode menu) (AUDIO menu) (AUDIO EXT.
English Outline of Button and Touchkey Operation ●When the 5.1 ch Surround Decoder is connected Owner’s manual (ADJUST mode menu) (AUDIO menu) (AUDIO EXT.
English Outline of Button and Touchkey Operation Adjusting the other system settings Owner’s manual (GENERAL menu) (ADJUST mode menu) (MONITOR menu) (MONITOR ADJ) (Monitor Adjust screen) (WALL COLOR) (WALL COLOR screen) Bright Color Hue Dimmer ∗Switched by touching this key repeatedly. ( “Hue” is not displayed when displaying PAL images.
English Remote Control Remote control unit Owner’s manual Signal transmitter Operating range: 30˚ in all directions [BAND] [MUTE] [SRC] [VOLUME] [P.TIME] [0-9] [DISC SEL] [ ],[ ] [SEARCH MODE] [MENU] [RTN] [TOP MENU] [SET UP] [ [ENT] ],[ ] [TA] [2-ZONE] [RPT] [SCN] [PBC] [RDM] [AUDIO] [SLOW] [ANGLE] [SUB TITLE] Inserting the Batteries 1. Slide the rear cover in the direction of the arrow, and remove it. 2. Insert the AA (SUM-3, IECR-6/1.
You can use the remote control unit to control the VRX878RVD. When the 2-ZONE function is ON, the controls work upon the selected zone. Shared modes [SRC] button • Press this button to switch the modes such as TUNER mode, DVD PLAYER mode. [VOLUME] buttons • Increase and decrease volume. [MUTE] button • Turns mute on and off. [RTN] button • Returns to the previous screen from the list or menu screens. • Displays the menu screen when playing a Video CD.
English Functions of Remote Control Unit Buttons [MENU] button • Press to display menu stored on video disc. Owner’s manual [SET UP] button • Press to show the DVD SETUP menu screen during DVD video playback. [TOP MENU] button • Press to display the Top Menu screen stored on DVD video disc. Some discs do not display the top menu screen. [E], [e], [T], [t] buttons • Press to select button items on the menu screen of a DVD video.
English Functions of Remote Control Unit Buttons [RDM] button • Press to play tracks of all discs at random. • Keep pressing more than 1 second to play folders of all discs at random. DVD changer mode * For details on DVD changer precautions, refer to the instruction manual of the DVD changer. [BAND] button • Press to switch discs. [P.TIME] button • Keep pressing more than 1 second to switch between the time progress and remaining time to be displayed.
English 4. CAUTIONS ON HANDLING Owner’s manual Liquid crystal panel/Generalities For a longer service life, be sure to read the following cautions. • Be sure to house the liquid crystal panel inside the main unit when parking the car outdoors for long period of time. The liquid crystal panel will operate properly in a temperature range of 0 to 60qC. • Do not allow any liquids on the set from drinks, umbrellas etc. Doing so may damage the internal circuitry.
English Handling Discs Storage • New discs may have some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc. • Do not expose discs to direct sunlight or any heat source. • Do not expose discs to excess humidity or dust. • Do not expose discs to direct heat from heaters.
English 5. DVD VIDEO SYSTEM Owner’s manual DVD video is a high-quality digital video source that provides crisp and clear images. One 12 cm disc contains either one film or four hours of music. DVD Video Features This unit provides the following functions in addition to the high image quality and sound quality of DVD video. Note: • The functions described in this section, for example, the recorded language, subtitles, angles, etc. differ depending on the DVD video disc.
English Discs Discs that cannot be played back This DVD video player can play the following discs. This DVD video player cannot play back DVDAudio, DVD-RAM, Photo CDs, etc. Playable discs DVD video discs video CDs CD TEXT Audio CDs MP3 ID3 TAG WMA About CD Extra discs Note: • It may also not be possible to play back CDs recorded on a CD-R unit and CD-RW unit. (Cause: disc characteristics, cracks, dust/dirt, dust/dirt on player’s lens, etc.
English 6. OPERATIONS Owner’s manual DCP (Detachable Control Panel) The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (Detachable Control Panel) case to prevent scratches. Attaching the DCP 1. Hook the right side of the DCP to the right side of the main unit. 2. Settle the left side of the DCP to the main unit. We recommend taking the DCP with you when leaving the car. Removing the DCP 1.
English Basic Operations CAUTION CAUTION When the unit is turned on, starting and stopping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume. Turning on and off the power When the liquid crystal panel is closed 1. Press the [SRC] button to change the operation mode.
English Basic Operations Mute Owner’s manual 1. When in the TUNER, VISUAL, TV or DAB mode, press the [p] button to turn the mute on and off. When in the DVD PLAYER, iPod or changer mode, keep pressing the [p] button more than 1 second to turn the mute on and off. • When the mute is turned on, “ ” appears at the bottom left of the screen. Opening and turning the liquid crystal panel WARNING • To prevent the battery from going dead, operate this unit with the engine running if possible.
Adjusting the angle of the liquid crystal panel When the way the liquid crystal panel is mounted hinders the operation of the air conditioner, the position of the panel can be turned horizontal temporarily. 1. Keep pressing the [P] (OPEN) button more than 2 seconds when the liquid crystal panel is open. A beep sounds and the liquid crystal panel turns horizontal. • Press the [P] (OPEN) button again for the panel to return to the original position.
English Basic Operations Owner’s manual Adjusting the balance/fader Adjusting the MID 2-1. Touch the []] key of the BAL/FAD item. The MID gain, MID frequency (centre frequency) and MID Q can be adjusted as follows. 3-1. Touch the [{] or [}] key to adjust to the fader level. • The factory default setting is “0”. (Adjustment range: front 12 to rear 12) [{]: Emphasises the sound from the front speakers. [}]: Emphasises the sound from the rear speakers. 3-2.
English Basic Operations Adjusting the MONITOR * The [ADJ] buttons is enabled only when the panel is open. Note: • The Color and Hue settings can be adjusted only in the DVD video, Video CD, TV/VTR, VISUAL and DVD changer modes, and only when the car is stopped and the parking brake is applied. • The Hue setting can be adjusted only when the NTSC mode is selected. 2-1. Touch the []] key of the MONITOR ADJ item to display the Monitor Adjust screen.
English Basic Operations Warning display when CCD camera is installed Owner’s manual The following warning message is displayed during use of the CCD camera: “Make sure of safety around your vehicle”. Adjusting the GENERAL 1. Press the [ADJ] button, then touch the [GENERAL] key. * The [ADJ] buttons is enabled only when the panel is open. 2-1. Touch the [ON] or [OFF] key of the CAMERA WARNING item to turn this function on or off (The factory default setting is “ON”).
Mobile phone interrupt setting The sound heard when you make operations is called “beep”. The unit can be set up so that it does not produce this beep sound. • The factory default setting is “ON”. When you connect your mobile phone to this unit using a separately sold cable, you can listen to your telephone calls on your car speakers. • The factory default setting is “OFF”. 3-1. Touch the [ON] or [OFF] key of the BEEP item to turn the function on or off. 3-1.
English Basic Operations Switching CONNECT (connect) Owner’s manual Make the following settings when an external device is connected to the Visual terminal. Note: • This function is not available when the Clarion navigation system (NAX963HD) is connected. • When the navigation system is connected, use the monitor lock function. Locking the monitor locks the screen size in F.WIDE mode (full wide), and the VTR system to NTSC if the CONNECT item is set to [COMPOSITE].
English Basic Operations 2-ZONE Function Setting the 2-ZONE function • The factory default setting is “OFF”. The 2-ZONE function is a function that outputs separate sounds/images from the MAIN zone and SUB zone (such as the optional rear monitor) by simultaneously operating two sources in the one centre unit. Thereby, plural listeners are allowed to enjoy separate audio/visual sources.
English Basic Operations Monitor image and sound with 2-ZONE ON/OFF ●With 2-ZONE function OFF Owner’s manual Front monitor lock ON Front monitor lock OFF Visual connection [OTHERS] (*1) Visual connection [RGB]/ [COMPOSITE] (*1) Visual connection [OTHERS] (*1) Visual connection [RGB]/ [COMPOSITE] (*1) Front monitor (liquid crystal panel) Displays image of device connected to the Visual terminal. (*3) Displays image of device connected to the Visual terminal.
Listening to the radio ●LOCAL SEEK If you keep touching the [X] or [x] key more than 1 second, the Local Seek tuning is carried out. The broadcast stations with good reception sensitivity are automatically selected. • When the Local Seek tuning starts, “LO SEEK” appears on the screen. Manual tuning 2. Press the [BAND] button or touch the [Band] key to select the radio band. Each time the button is pressed, the radio reception band changes in the following order: FM1 ➜ FM2 ➜ FM3 ➜ AM (MW/LW) ➜ FM1... 3.
English Radio Operations Owner’s manual Recalling a preset station Manual memory There are total of 24 preset positions (6-FM1, 6FM2, 6-FM3, 6-AM (MW/LW)) to store individual radio stations in memory. There are 2 ways available to recall the preset station. ●Using the [R] or [F] button 1. Press the [BAND] button to select the desired band (FM or AM (MW/LW)). 2. Press the [R] or [F] button to recall the previous or next stored station. ●Using the Preset List screen 1. Touch the [List] key. 1.
English RDS Operations AF function This unit has a built in RDS decoder system that supports broadcast stations transmitting RDS data. This system can display the name of the broadcast station being received (PS), and can automatically switch to the broadcast station with the best reception as you move long distances (AF switching). Also, if a traffic announcement or programme type information is broadcast from an RDS station, no matter what mode you are in, this broadcast is received.
English RDS Operations Manually tuning a regional station in the same network Owner’s manual Note: • This function can be used when a regional broadcast of the same network is received. • This function is enabled only when the AF function is ON, and the REG function is OFF. 1. Touch the [List] key on the RDS mode screen. 2. Touch your desired Preset key to call out a regional station. 3. Each time you touch the same Preset key, this unit switches from a local station to the other on the same network.
Preset number PTY item ENGLISH Contents 1 News News 2 Info Information 3. Touch your desired Programme Type key to select. 4. Touch the [Preset] key to display the Preset screen. Keep touching your desired Preset key on the Preset screen more than 2 seconds to store the selected programme type into the preset channel memory. • The 29 types of PTY listed below can be selected.
English RDS Operations Emergency broadcast Owner’s manual If an emergency broadcast is received, all the function mode operations are stopped. “ALARM” appears on the screen and the emergency broadcast can be heard. ●Cancelling an emergency broadcast 1. Touch the [Option] key on the RDS mode screen to display the RDS menu. 2. Touch the [OFF] key of the AF item. The emergency broadcast reception is cancelled.
English DVD Video Player Operations Note: • If the Setup operation is performed in the middle of DVD video play, the disc will restart from beginning. • The settings on the DVD SETUP menu cannot be set with the remote control unit. Selecting the DVD SETUP menu 1. Press the [SRC] button, and touch the [DVD PLAYER] key. The DVD PLAYER mode screen is displayed. 2. Touch the [Option] key to display the Option menu. 3. Touch the [Setup] key to display the DVD SETUP menu.
English DVD Video Player Operations Setting up the disc menu language Owner’s manual 4-1. Touch the []] key of MENU LANGUAGE item. The MENU LANGUAGE menu is displayed. 4-2. Touch the key to select a desired language to set it. • The factory default setting is “ENGLISH”. Setting up the audio language 4-1. Touch the []] key of AUDIO LANGUAGE item. The AUDIO LANGUAGE menu is displayed. 4-2. Touch the key to select a desired language to set it. • The factory default setting is “ENGLISH”.
Country LEBANON Input code 7666 7683 LIECHTENSTEIN 7673 LUXEMBOURG 7685 MACEDONIA, THE FORMER YUGOSLAV REPUBLIC OF 7775 MALTA 7784 MONACO 7767 NETHERLANDS 7876 (NETHERLANDS ANTILLES) 6578 NORWAY 7879 OMAN 7977 POLAND 8076 PORTUGAL 8084 QATAR 8165 ROMANIA 8279 SAN MARINO 8377 SAUDI ARABIA You can change the level of parental lock (audiovisual restriction).
English DVD Video Player Operations Owner’s manual Basic Operations Pausing play Loading a disc 1. Press the [p] button or touch the [p] key to pause play. “PAUSE” appears in the display. 2. To resume disc play, press the [p] button again. 1. Insert a disc into the centre of the insertion slot with the label side facing up. The disc plays automatically after loading. Note: • Never insert foreign objects into the disc insertion slot.
Operating the DVD menu Watching a DVD-Video You can select the button items displayed in the DVD menu by directly touching it. If the button items are hard to select correctly, you can also operate them by displaying Key Pad on the screen. After disc loading, the play mode is automatically engaged. • When playback is not started, press the [p] button or touch the [p] key. • Button operation may differ depending on the story of the disc.
English DVD Video Player Operations Owner’s manual Stopping playback Skipping a chapter (searching) 1. Showing the DVD PLAYER mode screen, touch and hold the [p] key for more than 1 second during playback. Playback is stopped. 2. To resume playback, press the [p] button. Playback resumes from the scene where playback is stopped. ●About chapter Chapter means a small segment to divide the data area of the disc. 1. Press the [R] or [F] button during playback.
Searching with a chapter/title number * If the input title/chapter number does not exist or searching with a title/chapter number is not allowed, the screen image will not change. 4. Touch the [Back] key. Scan playback Scans and plays back all chapters recorded on the DVD-Video, the first 10 seconds for each. 1. Showing the DVD PLAYER mode screen, touch the [Option] key. 2. Touch the [Chapter Scan] key, then touch the [Back] key. The message “C.SCN” will be displayed.
English DVD Video Player Operations Owner’s manual Switching among languages Switching angles On discs in which two or more audios or audio languages have been recorded, you can switch among the audio languages during playback. 1. Showing the DVD PLAYER mode screen, touch the [Option] key. 2. Touch the [Audio] key during playback. • Each time you touch the key, you can switch among audio languages. • It may take time to switch among audios.
Watching a video CD Note: • There are two types of Video CDs, and these differ in some operations and functions. For the operations and functions of a Video CD, see the documents attached to the Video CD. Showing the V-CD menu (for Video CD discs with PBC) * This key does not function on some discs. 1. Touch the screen to display the VIDEO CD mode screen, then touch the [Menu] key during playback. The Video CD menu appears. * The displayed contents may differ, depending on the Video CD software. 2.
English DVD Video Player Operations Searching with a track number Owner’s manual This operation allows searching with the track numbers recorded on the video CDs. 1. Touch the screen to display the VIDEO CD mode screen. 2. Touch the [Search] key. 3. Input the track number that you want to play back with [0] to [9] key. 4. Touch the [ENT] key. Playback starts from the scene of the input track number.
English DVD Video Player Operations Other various play functions 1. Press the [R] or [F] button during playback. Tracks are skipped, as many as the times the button is pressed, and playback starts. • Pressing the [F] button starts playback from the beginning of the next track. • Pressing the [R] button starts playback from the beginning of the current track. When this button is pressed again within about 2 seconds, playback starts from the beginning of the previous track. 1. Touch the [Option] key.
English DVD Video Player Operations Displaying CD titles Owner’s manual This unit can display title data for CD-text CDs. 1. Touch the [Title] key. 2. Touch the [X] key of the Disc, Artist, or Track item to cause the respective display to scroll once. Listening to an MP3/WMA This unit is an ID3 Tag compatible model. This unit supports the ID3 TAGs of the Version 2.4, 2.3, 1.1 and 1.0. In displaying, this unit gives priority to the Version 2.3 and 2.4 TAGs.
Note: • If Tag information was entered with 2-byte characters, it may occur that the characters are not reproduced properly on the display. • MP3/WMA files that the DRM (Digital Rights Management) function is set cannot be played. Regarding MP3/WMA folder creation Up to 8 folder levels (including the root directory) can be created for MP3/WMA files (items 1 – in the illustration). However, on this unit, folders created above the third level will be converted to 2 levels.
English DVD Video Player Operations Selecting a folder/track on the LIST screen Owner’s manual 1. Touch the [List] key during playback. Folder List screen is displayed. 2. When the desired folder is not displayed, touch the [v] or [V] key to scroll the list. 3. Touch the desired folder name key. The Track List screen appears. 4. Touch the [v] or [V] key to scroll the list, and touch the desired track name key. The corresponding track is started playback.
English Other Functions Title list play Titles up to 10 characters long can be stored in memory and displayed for CD, TV stations, and CDs in the CD changer. The numbers of titles that can be entered for each mode are as follows. You can display a list of titles, then select the CD track, disc or broadcast station to listen to from that list.
English Other Functions Owner’s manual Changing over monitor display size Internal amplifier cancel function • The factory default setting is “[F.WIDE]”. This function is used to disable the internal amplifier when an external amplifier is connected. • The factory default setting is “OFF”. 1. Press the [ADJ] button. 2. Touch the [AUDIO EXT.] key. 3. Touch the [ON] or [OFF] of the AMP CANCEL item to turn the internal amplifier on or off. 4. Touch the [Back] key to return to the previous screen.
English 7. ACCESSORIES This unit can be used to control a connected Apple iPod (iPod Mini, fourth generation, iPod nano, iPod with video). Note: • Note that iPod versions higher than those noted above may not be playable. • The unit will not operate, or may operate improperly with unsupported versions. • First, second and third generation iPod and iPod shuffle cannot be used. Controlling the iPod ●Selecting the iPod mode 1. Connect the iPod to the connector. 2. Touch the [iPod] key on the Source menu.
English iPod Operations Owner’s manual Note: • The title display (*) shows, from top level down, the SONG title, ARTIST name, and ALBUM title. Press the operation display to scroll the SONG title. ●Operation display Play/Pause icon(p) display Track No. Clock time Play mode (*1) Song title/ Artist name/ Album title (*2) Progress/ Volume indicator Play time Remaining time Note: *1 Displays status of Repeat, Shuffle play.
Viewing video data in the iPod (only for the iPod with video features) TOP function The TOP function resets the player to play the first track of the tracks. 1. Press the [BAND] button to play back the first track of the current list. Note: • Do not connect the iPod to this unit when a Video Playlists item is selected on the iPod. * To play back all of the tracks in the Songs list from the first track, keep pressing the [BAND] button more than 1 second. Selecting a list item from a list screen 1.
English VISUAL Operations This function is available when a VTR, etc. is connected to the visual terminal. Owner’s manual WARNING For your safety, the driver should not watch the VTR, etc. or operate the controls while driving. Please note that watching and operating the VTR, etc. while driving are prohibited by law in some countries.
English CD Changer Operations Switching to a next disc (Disc Up function) Other various play functions 1. Touch the [Option] key. Owner’s manual The disc up function plays from the first track (track No.1) of the next disc. 1. Press the [BAND] button. The disc changes to the next disc. Searching with a track number * This function is available only for the current disc. 1. Touch the [Search] key. 2. Input the track number that you want to play back with [0] to [9] key. 3. Touch the [ENT] key.
English DVD Changer Operations Owner’s manual Only basic operations of DVD changer can be performed from the unit. Use the remote control unit to perform the following functions. • Scan, Repeat, Random functions • Video CD Playback function ON/OFF • DVD Setup function, Audio, Subtitle, Angle setting function For details on operations other than those described below, see the pages of “DVD Video Player Operations” (page 39). For details on DVD changer precautions, refer to the supplied owner’s manual.
1. Press the [BAND] button or touch the [Band] key to select the desired band. (TV1 or TV2) 2. Tune into a station. Quick tuning: Touch and hold the [X] or [x] key for more than 1 second to tune in a station. Step tuning: Touch the [X] or [x] key to manually tune in a station. Note: • Manual tuning is cancelled if you do not operate the unit for 7 seconds. Recalling a preset station A total of 12 TV stations can be stored (6-TV1 and 6-TV2). There are 2 ways available to recall the preset station.
English Digital Radio/DAB Operations Owner’s manual About DAB programmes Seek tuning The DAB (Digital Audio Broadcasting) system transmits several programmes on one frequency simultaneously, by compressing audio signals. • A DAB station has multiple programmes on one frequency. • The group of programmes, which is transmitted on a single frequency is called “ensemble”. • Some DAB stations have several ensembles and broadcast diversified programmes.
Storing a programme to preset memory PTY This function enables you to listen to the selected programme type, regardless of the function mode. • DAB and RDS have the same PTY. • You can select one PTY from DAB or RDS. • PTY broadcast are not yet available in all countries. • In the information standby mode, INFO stations have priority over PTY stations. • In the TA standby mode, TP stations have priority over PTY stations.
English NAVI Operations (NAX963HD, etc.) Owner’s manual NAVI functions NAVI operation Note: • Hereafter in this section, the Navigation system will be called as “NAVI”. • When the Clarion NAVI NAX963HD is connected, the following functions are available: Changes between the NAVI display and the Audio/Visual (hereinafter, refered as “AV”) display.
English NAVI Operations (NAX963HD, etc.) [MENU] button • When in the NAVI mode, the MENU screen of the NAVI mode is displayed. Owner’s manual Connecting Other Company’s Image Equipment The RGB type or composite type images from the other company’s equipment can be displayed on this unit. Be sure to perform this setting after connecting the RGB type or composite type image equipment to the RGB terminal. 1. Press the [ADJ] button, and touch the [GENERAL] key. 2. Touch the []] key of the CONNECT item. 3.
English 5.1 ch Surround Decoder Operations Owner’s manual This function is available when an optional 5.1 ch Surround Decoder (DVH943N) is connected. When the 5.1 ch Surround Decoder is connected through the CeNET cable, the 5.1 ch Surround Decoder Control unit (DVC923, optional) cannot be used. ●SPEAKER SEL (speaker selection) This function determines centre speaker, surround speaker and subwoofer connection. 3-1. Touch the []] key of the SPEAKER SEL item to show the submenu.
* This function is not available for speakers whose SPEAKER SEL setting is set to “OFF”. 3-1. Touch the []] key of the FILTER item to show the submenu. 3-2. Touch the [[] or []] key of the FRONT HPF, CENTER HPF, SURROUND HPF or SUBWOOFER LPF item to adjust. [FRONT HPF]: This function can be set to the following four settings: 50 Hz, 80 Hz, 120 Hz or THRGH (through). “THRGH” is the default value. [CENTER HPF]: This function can be set to the following three settings: 50 Hz, 80 Hz and 120 Hz.
English 5.1 ch Surround Decoder Operations DSF mode Owner’s manual DSF effect ON/OFF • The factory default setting is “OFF”. 1. Press the [ADJ] button, and touch the [AUDIO] key. 2. Touch the []] key of the STATUS item. 3. Touch the [ON] or [OFF] key of the DSF item to turn the function ON or OFF. 4. Touch the [Back] key to return to the previous screen. Note: • If the DSF effect is set to OFF, the adjustment made in “DSF” is not reflected in the music source. Selecting the DSF type 1.
English 5.1 ch Surround Decoder Operations Selecting the Dolby PLII (Dolby Pro Logic II) type * This setting is disabled when both the CENTER SP and SURROUND SP items of the SPEAKER SEL setting are set to “OFF”. 1. Press the [ADJ] button, and touch the [AUDIO] key. 2. Touch the []] key of the Dolby PLII item. 3. Touch the key for the desirable type to select. 4. Touch the [Back] key to return to the previous screen. 3-1. Touch the []] key of the BAL/FAD item.
English 8. TROUBLESHOOTING Owner’s manual GENERAL Problem Cause Measure Power does not turn on. (No sound is produced.) Fuse is blown. Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. Nothing happens when buttons are pressed. The microprocessor has malfunctioned due to noise, etc. Turn off the power and remove the DCP. Press the reset button with a thin rod. Display is not accurate.
English TV/VTR (When connecting an optional TV tuner, etc.) Problem Cause Measure The parking brake is not engaged. Check that the parking brake is engaged. The display is dark. The brightness control is too low. Adjust the brightness properly. The operating condition is not good. The temperature inside the vehicle may be 0qC or lower. Set to an appropriate temperature (25qC or so) and check it again. The headlight of the vehicle The display is made dark at night to prevent the is lit.
English 9. ERROR DISPLAYS Owner’s manual If an error occurs, one of the following displays is displayed. Take the measures described below to solve the problem. DVD Player Display Cause Measure ERROR 2 A disc is caught inside the This is a failure of DVD deck’s mechanism and CD deck and is not ejected. consult your store of purchase. ERROR 3 A disc cannot be played due to scratches, etc. Replace with a non-scratched, non-warped disc.
English 10.SPECIFICATIONS LCD Monitor Frequency Range: 87.50 MHz to 108.
English INSTALLATION AND WIRE CONNECTION MANUAL INSTALLATION MANUAL 1. BEFORE STARTING 1. This set is exclusively for use in cars with a negative earth 12 V power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery “-” terminal before starting. This is to prevent short circuits during installation. (Figure 1) Car battery Figure 1 2.
5. Use the included screws for installation. Using other screws can cause damage. (Figure 4) Chassis Damage Max. 8 mm (M5 screw) Figure 4 6. The source unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles. (Figure 5) Dashboard T Gear lever (check that it does not touch the LCD.) Chassis INSTALLATION MANUAL 1. Prepare all articles necessary for installing the main unit before starting. 2.
Universal Mount INSTALLATION MANUAL Note: *1: Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. *2: Fasten the front stopper securely to prevent the main unit from coming loose. 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8 (see page 79). 3.
2. Secure the mounting brackets to the chassis as shown in Figure 8. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models. 3. Wire as shown in Section 8 (see page 79). 4. Secure the unit in the dashboard, and then reassemble the dashboard and the centre panel.
English 6. REMOVING THE MAIN UNIT INSTALLATION MANUAL 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and the universal mounting bracket, fit tab B of the spring into hole A of the hook plate, then pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) Note: • Keep the hook plate.
English 8. WIRE CONNECTION Radio antenna jack INSTALLATION MANUAL Note: • Before installing, be sure to disconnect the negative cable of the car battery. • In the optional devices, the RCA Pin and the Connector cable are separately-sold items.
English Power supply lead INSTALLATION MANUAL B-2 B-3 B-5 B-4 B-1 B-6 1 B-7 B-8 A-7 A-8 ∗3 2 A-6 ∗1 No.
Parking brake lamp + lead to battery ●How to attach the electro-tap 1. Place the Parking brake lead at the stopper, and fold it back in the direction of the arrow. Parking brake Electro-tap Parking brake signal lead 2. Pass the Parking brake signal lead through, and fold it back in the direction of the arrow.
English 9.
Clarion Co., Ltd. 2007/2 (HUN-YI) All Rights Reserved. Copyright © 2007: Clarion Co., Ltd.
