Owner's manual Mode d'emploi Manual de instrucciones VRX93SVD AM/FM DVD VIDEO / VIDEO CD / CD / MP3 PLAYER / CD CHANGER CONTROLLER WITH 7" LC DISPLAY CONTROLADOR DE RADIO DE AM/FM, REPRODUCTOR DE DISCOS DVDNIDEODISCOS CD/CD/MP3/CAMBIADOR DE DISCOS CD CON VISUALIZADOR DE CRISTAL L1QUIDO DE 7" D2!!1NET VRX9J5VD _ 3 I ~ _r Au""= ~ ~ (O@·CNRPT···BE-,E ~ tSJ~ jr::o ~~Ie e e 0 0 0 0 0 0e[@u "'''3~®D[]IDOLBY(lillDo~@ lillD~~ ID3 TAG ~ - DIG I TAL IOIGlTALVIDEOJ DIGITAL
Thank you for purchasing the Clarion VRX935VD. * This owner's manual is for the VRX935VD. * Please read this owner's manual in its entirety before operating this equipment. 0,: After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). * Check the contents of the enclosed warranty card and keep it carefully with this manual. This manual includes the operating procedures of the CD changer, MD changer, DVD changer, TV tuner, SIRIUS, Multiple Channel Processor (MCP).
2. PRECAUTIONS For your safety, the driver should not watch the TV or operate the controls while driving. Please note that watching and operating the TV while driving are prohibited by law in some countries. Also, while driving, keep the volume to a level at which external sounds can be heard. 1.
Handling Discs Handling Storage • New discs may have some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc. • Do not expose discs to direct sunlight or any heat source. Cleaning Ball-point pen ~ & • Do not expose discs to excess humidity or dust. • Do not expose discs to direct heat from heaters.
With the Display closed / Avec fafricheur / Con el visualisador cerrado -[OPEN] -~,,-~Ir ~~~~~~0~6~rl~~) [FUNC] -~7.--- -I [ [RELEASE] [SENSOR] '--[ISR] [MUTE] With the Display open / Avec fafficheur ouvert / Con el visualisador abierto ---[DISP] VOI-C]VOL+ VRX935VO -- - - [~::::---I~I---) r---~--- .
4. NOMENCLATURE Ji. Names of Buttons Note: • Be sure to read this chapter referring to the front diagrams of chapter "3. CONTROLS" on page 5 (unfofd). When the display closed [VOL] button [DIRECT] button • Use this button to increase/decrease the volume. • Use this button to select a preset channel in the radio/SIRIUS/TV mode. • Use this button to select a disc in the changer mode. • Press and hold one of the [DIRECT] button for 2 seconds or longer to store the current station into preset memory.
When the display open [<~], [~>] button • Use this button to tune to a station in the radio/SIRIUSrrV mode. • Use this button to select a track in the CD, Video CD, MP3 and CD/MD changer mode. • Use this button to select a chapter in the DVD video and DVD changer mode. [M.L] button • The display panel can be switched to a composite screen to lock the monitor or to view a video CD. • Press and hold this button for about 1 second or longer to turn off the monitor.
5.IlIIA[AX The Color LCD Display and the Information Panel on the main unit show the following displays, providing information about the mode and functions operated. Information Panel Preset channel indication \ Disc number indication \ *The disc numbers corresponding to the \\' discs in the DVD, CD or MD changer light. \ \ Operation status indication - - , \ \\ \\<\ *The frequency, play time, clock, etc. are displayed. \ ; (@ SC1~TRDM BEt$}ir.~ ~ ~~ !r.
\!RX835\!IJ
Note: screen. ~;'5: Touch the IRTNJ key to return to the prev:ous screen. :::6: Touch the ;':~7: Touch the key to go to the next menu.
\fRXS35VD
:\lotes: ::~8: or :onger. :·:<9: This ShOV1S a KEY PAD selection examp:e :n the radto mode \vhen 107.9 ivt-iz is seiected. screen.
Remote control unit ~Signal transmitter ~ ( [BAND] ~ ~I r:, '"' "'" C"~\ \ -~ II €5 ~ ~~I~I NTSC/PAL BAND CIJI:1) - \ \ fl, PTOME --II~ [....];:; I I ~?i#! [MENU][SEARCH MODE] ~;.,~-,--,«-~ [TITLE] j~ I I II II ,...,,"- - Li],['] -I I ~~O~ I~---_._-,,[ ...]' [~] I .........,..... G I I I I 0 0~ I I [ROM] Y-J? G!,q [SLOW] PS/AS [SCAN] -~ ~ [AUDIO] RPT IV clarion Inserting the Batteries 1.Turn the remote control unit over, then slide the rear cover in the direction of the arrow. 2.
Functions of Remote Control Unit Buttons e Shared modes [FUNC] button • Press and hold this button for 1 second or longer to turn on or off the power. Power on/ off, switches among radio, TV,etc. [VOLUME] button • Increases and decreases volume. [MUTE] button • Press to return to the first track in CD/MP-3 mode or video CD mode with the PSC function turned off. [P.TIME] button .. Press to turn on and off the playtime display in the DVD video and video CD mode.
Functions of Remote Control Unit Buttons r.A.], [.], [....], [....] button [SLOW] button • Press to select menus and other items during DVD video/MP-3 playback. • Press to perform slow playback in DVD video or video CD mode. [ENT] button • Press to confirm numerics entered in the KEY PAD operation screen. eCD/MD changer mode [I....] [...1] buttons • Press to switch discs. • Press to select the next higher or lower chapter number in DVD video mode.
The control panel can be detached to prevent theft. When detaching the control panel, store it in the OCP (DETACHABLE CONTROL PANEL) case to prevent scratches. 2. Press the right side of the OCP carefully to fit it in place. We recommend taking the OCP with you when leaving the car. Removing the DCP 1. Turn the power off. 2. Slide the [RELEASE] lever leftward to release the OCP/Operation Panel. 3. Press the [FUNC] button to turn on the power. • The DCP can easily be damaged by shocks.
LCD panel/Generalities For a longer service life, be sure to read the following cautions. .. Be sure to store the LCD panel inside the main unit when parking the car outdoors for long period of time. The LCD panel will operate properly in a temperature range of 0 to 60°C. • Do not place anything on the display when the panel is tilted. • The remote controller may not work if the remote control sensor is exposed to direct sunlight. .. Don't allow any liquids on the set from drinks, umbrellas etc.
DVD video is a high-quality digital video source that provides crisp and clear images. One 12 cm disc contains either one film or four hours of music. DVD Video Features This unit provides the following functions in addition to the high image quality and sound quality of DVD video. Notes: • The functions described in the section, "Features", for example, the recorded language, subtitles, angles, etc. differ with the OVO video disc. Refer to the instructions provided with the OVO video.
Discs TV color system This DVD player plays NTSC discs and PAL discs only and cannot be used for playback of SECAM discs. Playable discs This DVD video player can play the following discs. DVD video discs video CDs CD TEXT ~ [Q]m~@ ~n~W VIDEO [DIGITAL VIDEO) About MP3 playback This unit can play back CD-R/CD-RW discs on which MP3 music data have been recorded. For a detailed information, see the page entitled "Listening to an MP3". ~ Audio CDs rnJD~~ About the registered marks etc.
sure to this chapter referring to the front diagrams of chapter "3. CONTROLS" on page 5 (unfold). Adjusting the volume When the unit is turned on, starting and stopping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume. Note: • Use this unit after starting the engine. ~ \......!:7-WJ 1. Operate the [VOL] button in the direction of the + (up) or - (down) to adjust the volume; + : Increases the volume. - : Decreases the volume.
Basic Operations Adjusting the angel, etc. of the liquid crystal panel • To prevent the battery from going dead, operate this unit with the engine running, if possible. • When the liquid crystal panel is operating, be careful not to get your hand or finger caught between the panel and main unit or the instrument panel of the car. Standing up the liquid crystal panel 1. Press the [OPEN] button and the liquid crystal panel comes out and stand up automatically.
Basic Operations Turning the liquid crystal panel horizontal (Air conditioner operation mode) When the way the liquid crystal panel is mounted hinders the operation of the air conditioner, the position of the panel can be turned horizontal temporarily. 1. Press and hold the [OPEN] button when the liquid crystal panel is upright, and release the button when a beep is heard. 2. The liquid crystal panel turns horizontal.
Basic Operations Adjusting the MID '" The factory default setting is "0". (Adjustment range: front 13 to rear 13) The MID gain, MID frequency (center frequency) and MID Q can be adjusted as follows. [A] key: Emphasized the sound from the 1. Press the [A-M] button, then touch the [USER CUSTOM] key. [T] key: Emphasized the sound from the 2. Touch the [DETAIL] key, then touch the [MID] key. 3. When the bass type selection screen is displayed, touch the key for the desirable type to select it. 4.
Basic Operations Changing the setting of the display background Perform the setting of this function the car is stopped with the parking break applied. 1. Press the [DISP] button for 1 second or longer to show the background setup menu. '!' This menu can be displayed only in the radio, DVD (CD, MP3) or CD/MD changer mode and only while your car is deing driven. 2. Touch the setting key to show the setup display. • To set up the motion pattern 2-1. Touch the [MOTION] key to set a desired motion pattern.
Radio Operations Seek tuning Manual tuning 1. Press the [BAND] button and select the desired band. (FM or AM) There are 2 ways available: Quick tuning and step tuning. 2. Tune in to a station. * If "MANU" is lit in the display press and hold the [BAND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available. When you are in the step tuning mode, the frequency changes one step at a time. In quick tuning mode, you can quickly tune the desired frequency. 3.
Radio Operations Manual memory Instant station recall (ISR) 1. Press the [BAND] button and select the desired band. (FM or AM) Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. The ISR function even operates with the unit in other modes. 2. Select the desired station with seek tuning, manual tuning, or preset tuning. 3.
4, TouCh the LRTN} key to return the previews mode. medeA Settitlg fJ;;D tt~e screeti size Set up the screen size ac;cc)fcHna 2. The factory default setting ;s "OFF". key to return previous The coier of the seiected rtem changes. mode.
DVD Video Player Operations 2. Touch the key to select a desired language to set it. " The factory default setting is "ENGLISH". 3. Touch the [RTN] key to return previous mode. Setting up the audio language 1. Following the steps 1 to 2 in "Selecting the DVD SETUP menu", touch the [AUDIO LANGUAGE] key. 2. Touch the key to select a desired language to set it. " The factory default setting is "ENGLISH". 3. Touch the [RTN] key to return previous mode.
DVD Video Player Operations The relationship between DVD video category codes and parental level are shown in the table below. Use this table when setting the parental level. LEVEL? NC-17 (NO ONE 17 AND UNDER ADMITIED) LEVEL6 R (RESTRICTED) LEVEL4 PG-13 (PARENTS STRONGLY CAUTIONED) LEVEL3 PG (PARENTAL GUIDANCE SUGGESTED) LEVEL1 G (GENERAL AUDIENCES) • The contents that the parental level re· stricts varies with the country code.
DVD Video Player Operations Ejecting a disc 1. Press the [~] button a disc ejects. "EJECT" appears in the display. ::: The KEY PAD is not displayed in the menu screen while you are driving a car. * If a disc (12 cm) is left in the ejected position for 15 seconds, the disc is automatically reloaded. (Auto reload) ::: 8 cm discs are not auto reloaded. Be sure to remove it when ejected. Note: • If you force a disc into before auto reloading, this can damage the disc. Show the menu screen 1.
To perform rile (track) scan, touch the ~ To return to the STANDARD screen~ touch the [OFF] key. ififG'itc~ni;na a DVD-Video After disc loadlng> the play mode :s automatr" early engaged. • Button operatron may not be aHov/ed depend,.
DVD Video Player Operations Pausing playback 1. Press the [~/II] button during playback. Playback pauses. 2. To resume playback. Press the [~/II] button, and playback resumes. • The fast forward and fast rewind speed may differ depending on the disc. • The menu screen may appear when the button is pressed. Searching with number Slow playback 1. Press the [~/ill button then press and hold the [...> ] button.
DVD Video Player Operations This operation plays back chapters/titles recorded on the DVD-Video repeatedly. 1. Display the sub KEY PAD using the procedures described in the section "KEY PAD operation". • Chapter repeat: 2. Touch the [AUDIO] key during playback. Repeat playback Plays back one chapter repeatedly. 1. Touch the screen and touch the [SUB MODEj key. 2. Touch the [CHAPTER REPEAT] key, then touch the [RTN] key. 3. Touch the [CHAPTER REPEAT] key, repeat playback is turned off.
.. 8utton operation may not be alIO'Ned depending en the story of the disc. D·epending on the d~sc. s\\ntc~rm"'lq may be completely impossible or im1;)0~5sjbie on som l2 scenes. o it may take time to s\."",,:j status or disc. To select the menu contents.
DVD Video Player Operations Stopping playback Fast forward and fast backward 1. Press the [~/II] button for 1 second or longer during playback. Playback stops. 1. Press and hold the [<-.] button or [~>] button during playback. • When the PBC is turned on Resume playback When the Play/pause [~/II] button is pressed, the disc plays from the beginning. .When the PBC is turned off To resume playback, press the [~/II] button, and playback resumes from the scene where playback is stopped.
DVD Video Player Operations 3. Touch the touch key of the function you want to play. • [TRACK SCAN] This operation scans and plays back all tracks on the disc, the first 10 seconds for each. "TRACK SCN" will appear in the screen during play. On/off of Playback Control * This function is enabled only using the remote control unit. '" The factory default setting is "ON". On video CDs equipped with Play Back Control function, you can turn it on/off. 1. Press the [PBC] button on the remote control .
DVD Video Player Operations Skipping a track (searching) 1. Press the [<....] or [.->] button during playback. Tracks are skipped, as many as the times the button is pressed, and playback starts. • Press the [.->] button, and playback starts from the beginning of the next track. • Press the [<....] button, and playback starts from the beginning of the current track. When this button is pressed again within about 2 seconds, playback starts from the beginning of the previous track.
DVD Video Player Operations What is MP3? MP3 is an audio compression method and classified into audio layer 3 of MPEG standards. This audio compression method has penetrated into PC users and become a standard format. This MP3 features the original audio data compression to about 10 percent of its initial size with a high sound quality. This means that about 10 music CDs can be recorded on a CD-R disc or CD-RW disc to allow a long listening time without having to change CDs.
DVD Video Player Operations Fast forward and fast rewind 1. Press and hold the [<...] button or [...> ] button during playback. Press the button, and the playback speed becomes 4-time faster first and then 8-time faster 3 seconds later. Release the button, and the normal speed is restored. Selecting a file (track) on the screen 1. Press the [MENU] button during playback. 1. Touch the screen and touch the [SUB MODE] key. 2. Touch the [TRACK SCAN] key, then touch the [RTN] key.
DVD Video Player Operations Listening to files in a folder repeatedly (Folder repeat playback) Changing the display of the playback status This operation plays back files in an MP3 folder repeatedly. 1. Touch the screen and touch the [SUB MODE] key. 1. Press the [KEY PAD] button and touch the [P.TIME] key for 1 second or longer during playback. 2. Touch the [FOLDER REPEATl key, then touch the [RTN] key. The monitor displays "FOLDER RPT" and folder repeat playback starts. 3.
VISUAL Operations This function is available when a VTR, etc. is connected to the visual 1 or visual 2 terminal. * The visual 1 mode is not available when a DVD changer is connected to the visual 1. For your safety, the driver should not watch the VTR, etc. or operate the controls while driving. Please note that watching and operating the VTR, etc. while driving are prohibited by law in some countries.
VISUAL Operations • "WIDE": (wide mode) The image at right and left ends in a display elongates horizontally. • "F. WIDE": (full wide mode) The whole image elongates horizontally. • "CINEMA": (cinema mode) The image at both top and bottom in a display disappears. Notes: • When a normal 4:3 size image, not being a wide one, is viewed by displaying it fUlly on a wide monitor display in a wide mode or a full-wide mode, a part of the peripheral image will be lacking or deformed.
VISUAL Operations .Lock system monitor image and sound ~ ~~~;1)1----' ------ Front monitor (*1) Visual 2 connection "'", [OTHERS] Front image (receiver screen) 1-- Image of device connected to the Visual 2 terminal (';'3) --- Rear monitor image (separately sold) __ .~_~_._._ I Image of device connected to the Visual 2 terminal I Image of device connected to the Visual 2 terminal (:::3) _~...... I ..
VISUAL Operations Switching CONNECT(connect) Make the following settings when an external device is connected to the VISUAL 2 terminal. NAVI: when a navigation system is connected ,; When a navigation system is connected, use the monitor lock function. Locking the monitor locks the screen size in FWIDE mode (full wide) and the VTR system to NTSC. OTHERS: for external devices other than a navigation system when no external devices are connected ,The factory default setting is "NONE". NONE: 1.
CD/MD Changer Operations When the panel is open: 1. Press the [DISP] button. The disc title, track title, artist title and user title IS displayed. 2. Touch the [DISC] key, [TRACK] key, [ARTIST] key or [USER] key to select the desired title. The selected titles except for the user title scroll once. 3. Press the [DISP] button again. The STANDARD screen is returned and the selected title is displayed.
CD/MD Changer Operations Selecting tracks with the KEY PAD * This function displays the KEY PAD on the screen and allows you to select and repeat tracks you wish to listen to. Press the [KEY PAD] button to display the KEY PAD. • Track-down 1. Press the [<....] button to move back to the beginning of the current track. 2. Press the [<....] button twice to move to the beginning of the previous track. :I: When the panel is open, the same operation is also available by using the [<....] button in the panel.
CD/MD Changer Operations Scan play Disc repeat play The scan play locates and plays the first 10 seconds of each track on a disc automatically. This function continues on the disc until it is cancelled or the mode is changed. The scan play is useful when you want to select a desired track. Touch the screen or press the [LIST] button, the MENU screen appears. After all tracks in the current disc have been played, the disc repeat play automatically replays the current disc over from the first track.
DVD Changer Operations This function allows you to control a connected OVO changer in the same way as described in OVO player Operation. For details on operations other than those described below, see DVD player Operation. For details on DVD changer precautions, refer to the supplied owner's manual. Selecting a disc When the panel is closed: Each of the [DIRECT] button corresponds to a disc loaded into the DVO changer. Press the [DIRECT] button (1 to 6) and select the desired disc.
TV Operations Seek tuning Manual tuning 1. Press the [BAND] button and select the desired TV band (TV1 or TV2). * If "MANU" is lit in the display, press and hold the [BAND] button for 1 second or longer. "MANU" in the display goes off and seek tuning is now available. There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In quick tuning mode, you can quickly tune the desired frequency. 2.
TV Operations Manual memory 1. Select the desired station with seek tuning, manual tuning or preset tuning. 2. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station to that preset memory. Auto store Auto store selects 6 TV stations automatically and stores each one into a preset memory. If there are not 6 stations with good reception, stations previously stored in memory remain and only the strong stations are stored into memory. 1.
Sirius operation What is Sirius Satellite Radio? \/ ~,SIRIUS Satellite Radio Sirius is radio the way it was meant to be: Up to 100 new channels of digital quality programming delivered to listeners coast to coast via satellite. That means 50 channels of completely commercial-free music. Plus up to 50 more channels of news, sports, and entertainment from names like CNBC, Discovery, SCI-FI Channel, A&E, House of Blues, E!, NPR, Speedvision and ESPN.
Sirius operation Displaying radio text * Radio text is only displayed for stations that transmit such information. Touch the screen in the STANDARD screen to display radio text. Selecting stations with the KEY PAD This function displays the KEY PAD on the screen enabling you to tune in through auto store, preset scan or by entering a frequency. Press the [KEY PAD] button to display the KEY PAD. Tuning mode (T-MODE) There are two channel selection modes: seek mode and manual mode.
Sirius operation 3. Touch the [DIRECT] key (1 to 6) to select the desired preset station. 4. Touch the [RTN] key to return to the previus mode. .Using the [DIRECT] button 1. Press the [BAND] button and select the desired SIRIUS band (SR1, SR2 or SR3). 2. To recall a stored SIRIUS station, press the desired [DIRECT] button to select that station. ", Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory. Manual memory 1.
Sirius operation Scan function There are two scan modes: a category scan mode and a preset scan mode. During scanning channels are displayed in abbreviated form and the display mode cannot be switched. • Category scanning In a category scan, broadcast channels in the same category as the current channel are selected about every 10 seconds. 1. Touch the screen in the STANDARD screen. 2. Touch [SUB MODE] to open the SUB MODE screen. 3. Touch the [CATEGORY SCAN] key.
Other Functions 4. Touch the [TITLE INPUT] key in the MENU screen. The title input mode display appears. 5. Touch the characters, symbols, etc. shown in the display to input titles. Setting the auto dimmer The brightness of the color LCD display is adjusted automatically in proportion to the surrounding light. The auto dimmer function can switch between ON and OFF. "-ttt-" : Centering ON :Auto dimmer function is set. "BS" : Backspace OFF:Auto dimmer function is cancelled.
Other Functions Setting the beep * The sound heard when you make operations is called "beep". The unit can be set up so that it does not produce this beep sound. * The factory default is "BEEP ON". 1. When the panel is open, press the [ADJ] button to select the ADJUST MODE menu. 2. Touch the U.] key to select "BEEP". Touch the [BEEP] key to select "ON" and "OFF". 3. Touch the [ON] or [OFF] key to select a desired mode and set it. 4.
is·'3". ThlS functron :s used to seiect filter 'frequencies that surt the speakers that are used. 3. 0:>uch the requIred keys to make thIs desired setting, €)$PEAKER SEL (speaker s01) This 'functron determines center speaker, surround speaker and sub vvoofer connecticn. 3-; Touch t(>$ [SPEAKER SELl k<2)1 to sho\;v the submenu, < OUND SP} or [SUB WOOFER] key and the "ON" or "OFF" to turn speakers on or off deon \vhat speakers are connected. This function can be set to the value.
5. 1 ch Surround Decoder Operations • SPEAKER GAIN This function sets speaker output level. This function is not available for speakers whose SPEAKER SEL setting is set to OFF. 3-1. Touch the [SPEAKER GAIN] key to show the submenu. 3-2. Touch the [FRONT L], [CENTER], [FRONT Rl, [SURROUND R], [SURROUND L] or [SUB WOOFER] key to set respective item. 3-3. Touch the[.] or [T] key to make adjustments in the range -10 dB to +10 dB in 1 dB step increments. The default value is "0 dB".
5.1 ch Surround Decoder Operations DSFmode .SIGNAL DSF effect ON/OFF * The factory default setting is "OFF". This function selects [Po NOISE] or [MUSIC]. ", The factory default setting is "P.NOISE". .SPEAKER SELECT 1. Press the [A-M] button. ':' The factory default setting is "FRONT'. 2. Touch the [STATUS] key. This function selects [FRONT], [CENTER] or 3. Touch the [DSF] key to select "on" and "off", [SURROUND]. 4.
Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. The microprocessor has malfunctioned due to noise, etc. Turn off the power, then press the [RELEASE] lever and remove the OCR Press the reset button both of tuner amp unit and main unit for about 2 seconds with a thin rod. Note: When the reset button is pressed, turn off the ACC power.
The brightness control is too low. Adjust the brightness properly. The operating condition is not good. The temperature inside the vehicle may be aoc or less. Set to an appropriate temperature (25°C or so) and check it again. The headlight of the vehicle is lit. The display is made dark at night to prevent the glare (When the headlight of the vehicle is lit in the daytime, the display gets dark). The color is not adjusted adequately. Check that COL and HUE are adjusted properly.
n3. EIiIIiIUR DI5RlJ~Y5 This is a failure of CD deck's mechanism and consult your store of purchase. A CD cannot be played due to scratches, etc. Replace with a non-scratched, non-warped-disc. A CD is loaded upside-down inside the CD Eject the disc then reload it properly. deck and does not play. A CD inside the CD changer is not loaded. This is a failure of CD changer's mechanism and consult your store of purchase. A CD inside the CD changer cannot be played due to scratches, etc.
FMTuner General Frequency Range: 87.9 MHz to 107.9 MHz Usable Sensitivity: 9 dBf 50dB Quieting Sensitivity: 15 dBf Alternate Channel Selecitivity: 70 dB Stereo Separation(1 kHz): 35 dB Frequency Response(+/-3 dB): 30 Hz to 15 kHz Power source voltage: 14.4 V DC (10.8 to 15.6 V allowable) Ground: Negative Current consumption: 4.
VRX935VD Installation and Wire connection manual II Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. BEFORE STARTING PACKAGE CONTENTS GENERAL CAUTIONS CAUTIONS ON INSTALLATION INSTALLING THE MAIN UNIT REMOVING THE MAIN UNIT CAUTIONS ON WIRING WIRE CONNECTION SAMPLE SySTEMS 65 65 66 66 67 69 69 70 73 -1 . BEFORE STARTING 1. This set is exclusively for use in cars with a negative ground 12 V power supply. 2. Read these instructions carefully. ~. Be sure to disconnect the battery" 8" terminal before starting.
-3. GENERAL CAUTIONS 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service centre. 2. Use a soft, dry cloth to clean the case. Never use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently. -4. CAUTIONS ON INSTALLATION 1.
-5. INSTALLING THE MAIN UNIT • Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose. 3.
• Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (*). (Figure 8) If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the main unit in the following procedure. 1. Remove the screws from both side of the main unit.
-6. REMOVING THE MAIN UNIT 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and the universal mounting bracket, fit tab ® of the spring into hole ® of the hook plate, then Note: Keep the hook plate.
-8. WIRE CONNECTION Securely connect to the metal part of the car with a screw, etc. Black Main power supply cord ~==~~~---------~I I I I I I Main unit I I t/ I I Connection cord (provided with this unit) I I I I ~C __ e_N_E_T_c_a_bl_e_(_S_o_ld_s_e_p_ar_a_te_ly-/) I I I i I I Power supply lead / . _ . _ . _ . _ . _ . _ . _ . _ . _ . _ . _ . _ . _ . _ . - . _ . _ . _ .. I ,._, VIDEO output (RCA) *5 - - - i ! VISUAL 1 audio input terminal L+R (RCA) I I .
Purple/Black ® Purple CD Green/Black ® Blue/White @ Green (j) Brawn @*1 Glay ® Grass-green ® Glay/Black No.
• Connecting the Accessories • Connection to the external amplifier The external amplifier can be connected unless the MCP (Multiple Channel Processor) is connected. For detailed information, refer to the instruction manual of the MCP. • Connection to the CCO camera for vehicle The CCO camera for vehicle can be connected to the system expansion terminal on the main unit. For detailed information, refer to the instruction sheet or manual for the CCO camera.
-9. SAMPLE SYSTEMS • Sample System 1 MAIN UNIT VRX935VD ~ ~RCA Cable ., (Visual) VISUAL 2 IN 1..- ...-----------. B-1 VTR TUN~~I:MP r b .-------------, 1 Tuner CCA- 389 i I~ TTX7501z (CeNET TV TUNER) CeNET 4- VISUAL 1 IN o CD z m -I Rear view monitor DSH920S (SIRIUS TUNER) CeN ET L ,.--;==================~ VCZ625 (DVD CHANGER) CeNET Mode* Front Speaker Rear Speaker *Switch the MODE switch to the CeNET mode.
• Sample System 2 MAIN UNIT VRX935VD Optical Digital Cable (included the DVH920) (Gray) .RCA Cable :1 (Visual) ...---_-----, . r----.. d VISUAL 2 IN!... 1:lB-f ~CCA-38$! ~ b Tuner IN 1 r TUNER AMP UNIT TTX7501z (CeNET TV TUNER) CeNET (LINE IN)D la N(L1NE OUT) I Set the select switch to "(LINE IN)D". Rear view monitor ~--.~ ........_--.-Q3 ,...-_.. ,..----·I~ ~ DVH920 (Maltiple Channel Processor) CeNET Mode::: ::J Q. C 0..
• Sample System 3 MAIN UNIT VRX935VD (Gray) Optical Digital Cable (included the DVH920) iliRCA Cable :; (Visual) VISUAL 2 IN ~ B-f ~I .";.'i •., ~~ VTR .----------, r--b Tuner IN TUNER AMP UNIT TTX7501z 1 r (CeNET TV TUNER) CeNET CCA-389 :::::J 4- VISUAL 1 IN ~ JJ 0.. C (LINE IN)D N(L1NE OUT) .-+-(0 ::JZ CD 0- 0-1 Set the select switch "N(LlNE OUT)". m p) c::ii Rear view monitor ~o o » o < I ro
Clarion Co., Ltd. All Rights Reserved Copyright © 2002: Clarion Co.
~ CAUTION With the screen open, a driver may not see the disc insertion slot. For your safety, insert a disc with the screen closed. ~ PRECAUTION Lorsque Ilecran est ouvert, il est possible que Ie conducteur ne voie pas la fente d1insertion du disque. Pour votre securite inserez Ie disque avec Ilecran terme. ~ PRECAUCION Con la pantalla abierta, es posible que el conductor no pueda ver la ranura de inserci6n del disco. Para su seguridad, inserte el disco con la pantalla cerrada.
281-0624-00 2002/4 (A) Clarion LIMITED WARRANTY INFORMATION For USA and Canada only This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase. Clarion ProAudio products, except for speakers, are covered by a two year limited warranty when installed by an authorized Clarion dealer.
••••• , 0 • SOU II D " ' u ... o.
100 CHANNELS OF THE BEST ENTERTAINMENT ON THE ROAD Clarion siriusradio.
60 ORIGINAL MUSIC CHANNELS, ALL COMMERCIAL-FREE. PLUS 40 WORLD-CLASS SPORTS, NEWS AND ENTERTAINMENT CHANNELS -~.~- "a.. .. ".,., \ '7 .. T<>p 40 H;lS 3 . "'dol, Coni_a..,. "" Pop Mi, 5 ~- 7 ~ 8 9 ~ 2 ~ ~ Best Bes' Bes' Best me of 70:1 of tile ao. of .... !:IO:I , EcloctJ< RoxI< Rock HI.. ModenoRock Moono_ Rock 23 fl<>dl aa - RoxI<. 24 25 C1a>sK ........ n&tr¥e 26 11 _ 12 tr¥e I _. ~~- M" 0..... Country eou",')' ao..
GET READY FOR 100 CHANNELS OF THE BEST IN-CAR ENTERTAINMENT. You've just purchased a Sirius Satellite Radio receiver that's going to plug you into 60 original music channels, from today's hits to R&B oldies to classical masterpieces. From authentic country and real bluegrass to cool jazz, hot latin, reggae and rock. Plus 40 channels of world-class sports, news and entertainment, like ESPN, Radio Disney, EI Entertainment Radio, CNBC, Fox News and Discovery Radio. EXPERIENCE SIRIUS IN TWO SIMPLE STEPS.
