Owner’s manual & Installation manual Mode d’emploi et manuel d’installation Manual de instrucciones y de instalación XN 3210 XN 3410 XN AMPLIFIERS AMPLIFICATEURS XN AMPLIFICADORES XN XN3210_3410 manual_060410 R2.
INTRODUCTION English The Clarion XN3210 is a full-featured, two-channel amplifier incorporating the following features: • Specially coated circuit boards that resists mold, mildew and moisture damage. • Pulse-Width Modulated (PWM) MOSFET power supply for maximum performance with minimal distortion. • Remote turn-on with "soft start" muting to prevent turn-on "thump". • Variable high-pass/low-pass electronic crossover with a 12dB per octave slope (adjustable range: 55Hz to 5.5kHz).
DESCRIPTION English Owner’s Manual The XN3210 and XN3410 use an unregulated MOSFET power supply for superior sound and output wattage. In addition, a toroid-coil is used to transfer power with minimal performance loss due to heat. To avoid unwanted noise, a doublesided conformal printed circuit board with strategically placed components keeps AM RFI subdued. All of the connections and controls for the XN3210 and XN3410 are conveniently located at the ends of the amplifier and labeled appropriately.
XN3210 2 INPUT GAIN HIGH INPUT MIN MAX + CH1 – CH1 + CH2 – CH2 GND 3 BASS BOOST 0 dB 15 CH1 4 5 FREQ RANGE FREQ Hz 55 6 X-OVER 7 9 MODE POWER English 1 110 240 550 330 X1 X10 LPF HPF OFF STEREO CH1/2 MONO CH2 MONO CH2 Owner’s Manual 8 1. CH1-CH2 RCA Input 2. Gain Control 3. Bass Boost 4. CH1/CH2 Frequency Control 5. Frequency Range Multiplier 6. Crossover Mode Switch 7. Output Mode Selector Switch 8. High Input 9.
English Owner’s Manual • Output Mode Selector Switch: CH 1/2 and CH 3/4 (XN3410 only) STEREO: Full left and right stereo operation. CH1Mono / CH2 Mono: Single channel input for bridged operation. This is especially useful in high-powered systems. (Uses CH2 and CH4 inputs.) CH1/2 Mono / CH3/4 Mono: Allows for a stereo input to be summed into a mono output. • CH1/2 FREQ / CH3/4 FREQ (XN3410 only) The CH1/2 crossover frequencies are adjustable from 55Hz to 550Hz.
XN3410 - Electrical Connection Remote Turn-On F U S E English 4 Ω BRIDGED + CH1 – + CH2 GND – REM +12V FUSE 30A + CH3 – + CH4 30A – 4 Ω BRIDGED Owner’s Manual CH4 Speaker (-) CH1 Speaker (+) CH1 Speaker (-) CH4 Speaker (+) CH2 Speaker (+) CH3 Speaker (-) CH2 Speaker (-) CH3 Speaker (+) Fig. 3 XN3210 1 2 3 4 Ω BRIDGED + L – + GND R 4 5 REM +12V 6 FUSE 40A – 1. Left Speaker Output 2. Right Speaker Output 3. Ground 4. Remote Turn-on 5. Battery 6.
INSTALLATION This section suggests Mounting and Wiring Precautions for installing the Clarion XN3210 and/or XN3410 amplifier(s). If you do not posses the necessary tools and installation experience, do not attempt to install these amplifiers. Instead, contact your local Clarion Marine Audio dealer to perform the installation. English MOUNTING PRECAUTIONS Owner’s Manual Prior to mounting the amplifier, make sure it is safe to mount the amplifier in that location.
English 7. When creating passage holes for power cables, RCA's cables, and speaker wires, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit. 8. Extra cable can cause signal loss and act as an "antenna" for noise. Use only high-quality RCA cables that are no longer than necessary. 9. In multiple amplifier systems, it is recommended to use a relay on the remote turn-on lead of the radio.
Fig. 5 4-Channel Stereo System, 2-Channel High-Pass, 2-Channel Low-Pass English Owner’s Manual 4 Ω BRIDGED + CH1 – + CH2 – GND REM +12V FUSE 30A + CH3 – + CH4 30A – 4 Ω BRIDGED CH3 Speaker System CH1 Subwoofer CH4 Speaker System CH2 Subwoofer In this 4-channel system, the XN3410 drives a pair of stereo satellites for the front and a pair of subwoofers. Note the filter settings. 10 XN3210/XN3410 XN3210_3410 manual_060410 R2.
Fig. 6 2-Channel Stereo System with Low-Pass Bridged Mono Channel English Owner’s Manual 4 Ω BRIDGED + CH1 – + CH2 GND – REM +12V FUSE 30A + CH3 – + CH4 30A – 4 Ω BRIDGED CH3 Speaker System CH4 Speaker System Subwoofer The XN3410 can also be used to drive a pair of stereo satellites for the front and a single mono subwoofer for the rear. Note the filter settings. XN3210/XN3410 XN3210_3410 manual_060410 R2.
Fig. 7 2-Channel High Power System (Satellite or Subwoofer) English Owner’s Manual 4 Ω BRIDGED + CH1 – + CH2 – GND REM +12V FUSE 30A + CH3 – + CH4 30A – 4 Ω BRIDGED Bridged CH1/CH2 Speaker System Bridged CH3/CH4 Speaker System OR Bridged Left Subwoofer Bridged Right Subwoofer The XN3410 can be set up as a 2-channel high power amplifier to drive a pair of satellites (or subwoofers) 12 XN3210/XN3410 XN3210_3410 manual_060410 R2.
Fig. 8 Mixed Mode System On CH3/CH4, Full Range Speakers On CH1/CH2 English 4 Ω BRIDGED CH1 – + CH2 GND – REM +12V Owner’s Manual + FUSE 30A + CH3 – + CH4 30A – 4 Ω BRIDGED CH3 Speaker CH4 Speaker C C CH1 Speaker L Subwoofer CH2 Speaker FREQ (Hz) L (mH) C ( F) 80 100 125 150 200 8.0 6.4 5.1 4.2 3.2 497 398 318 265 199 NOTE: Chart values based on 4 Ohm speakers. The amplifier can be configured for a mixed-mode operation on either channels 1/2 or 3/4 amplifier sections.
XN3210 WIRING AND APPLICATIONS The Clarion XN3210 2-channel marine audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. English Fig. 9 Bridged - Mono Subwoofer System Owner’s Manual 4 Ω BRIDGED + L – + GND R – REM +12V FUSE 40A Set X-Over Mode to LPF and adjust FREQ to speaker specifications. Subwoofer 4 Ohms In this application the amplifier is bridged for mono operation to drive a subwoofer. Note the filter settings.
Fig. 10 2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) L – + GND R REM +12V – English 4 Ω BRIDGED + FUSE 40A Owner’s Manual Left Full Range Speaker Right Full Range Speaker Set X-Over Mode as shown. Left Component Speaker System Right Component Speaker System Set X-Over Mode as shown. Adjust FREQ to speaker specifications. Left Subwoofer Right Subwoofer Set X-Over Mode as shown. Adjust FREQ to speaker specifications.
Fig. 11 Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) English 4 Ω BRIDGED + L – + GND R REM +12V – FUSE 40A Owner’s Manual Left Speaker Right Speaker C C L Subwoofer 4 Ohms FREQ (Hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (µF) 497 398 318 265 199 NOTE: Chart values based on 4 Ohm speakers. The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave crossover at specified frequencies.
SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Check. 1. Turn the Gain Control all the way counter-clockwise. English 2. Turn the ON/OFF Switch on the source units to the ON position. Set all Tone or Equalization Controls to "flat" positions and turn Loudness off. Owner’s Manual 3. Play a CD, set the Volume Control at 75% of full level. NOTE: If the system uses an equalizer, set its frequency controls to "flat" positions.
FINAL SYSTEM CHECK English 1. Turn on the source unit. After a two-second delay, slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections and refer to the Troubleshooting section. Depending on your system design, the levels may become quite loud even at low Volume Control settings. Until you get an "audio feel" of the system's power, use care when adjusting controls. Owner’s Manual 2.
Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) English Problem Audio lacks punch. Owner’s Manual Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check polarity of wires from amplifier to each speaker as defined by the system design. Problem Amplifier fuse keeps blowing. Solution Incorrect wiring or short circuit.