4289 Bonny Oaks Drive • Chattanooga, TN 37406 TEL: (800) 426-3738 • FAX: (800) 325-8871 Email: claritycs@plantronics.com Website: www.clarityproducts.
E N G L I S H JV JV-35 The Talking Phone ™ F R A N Ç A I S Operating Instructions Ameriphone products are manufactured by Clarity®, a Division of Plantronics, Inc. 4289 Bonny Oaks Drive, Chattanooga,TN 37406 Tel: (800) 426-3738 Fax: (800) 325-8871 Email: claritycs@plantronics.com Website: www.clarityproducts.com ©2004 Clarity, a Division of Plantronics, Inc. All rights reserved. Ameriphone, Amplifying Your Life, Clarity and The Talking Phone are trademarks or registered trademarks of Plantronics, Inc.
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . ii Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Package Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Features Identification . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation A. Desk mounting . . . . . . . . . . . . . . . . . . . . .4 B. Wall mounting . . . . . . . . . . . . . . . . . . . . .4 C. Batteries . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and persons including the following: 1.Read and understand all instructions. 2.Follow all warnings and instructions marked on the telephone. 3.Do not use this telephone near a bathtub, wash basin, kitchen sink or laundry tub, in a wet basement, near a swimming pool or anywhere else there is water. 4.
Important Safety Instructions dangerous voltage points or short out parts that could result in a risk of fire or electrical shock. Never spill liquid of any kind on the telephone. 13. To reduce the risk of electrical shock, do not take this phone apart. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 14.
Important Safety Instructions may explode. Check with local codes for possible special disposal instructions. ADDITIONAL SAFETY NOTES FOR CANADIAN USERS The following items are included as part of the CS-03 Requirements. The standard connecting arrangement for the equipment is CA11A. This product meets the applicable Industry Canada technical specifications. NOTICE: The Canadian Department of Communications label identifies certified equipment.
Important Safety Instructions CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalent Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface.
E N G L I S H Introducing the JV-35 Thank you for selecting the exciting new JV-35 from Ameriphone. It has been designed to meet the highest quality standards to provide you with years of convenient and trouble-free service Please read these operating instructions thoroughly before using your telephone. Keep this manual for future reference. You must save your sales receipt as proof of purchase in the event that you need warranty service.
Package Checklist Handset Base Unit Phone Cords JV-35 Telephone Line Cords Handset Coil Cord 2 Phone Base Plate Figure 1 - Package Components OPERATING INSTRUCTIONS AND QUICK GUIDE Operating Guides
E N G L I S H Features on the JV-35 Ringer volume control switch Audio output jack AC adapter Announcement switch Tone / Pulse switch Emergency buttons Braille characters Raised letters for easy identification REDIAL button MEMORY button HOLD button TONE selector Figure 2 - Base Unit Controls VOL control (volume) AMPLIFY button PROG button (program) 3
Installation A. Desk Mounting 1. Plug in the long phone cord. 2. Plug the handset cord into the telephone. B. Wall Mounting 1. Pull the handset hook out and reverse its position so that the hook points up. Fig. 4- Repositioning the hook Fig.3 - Connections and installation 3. Insert the AC Adapter cord into the receptacle on the back of the JV-35. Then plug the AC Adapter into an electrical outlet. 2. Install the Base Plate by sliding the small tabs into the upper slots.
E N G L I S H Installation 3. Plug in the short phone cord. 6. Lift the handset and listen for a dial tone. 4. Insert the AC Adapter cord into the receptacle on the back of the JV-35. Then plug the AC Adapter into an electrical outlet. 7. Your JV-35 is ready to use. Fig. 6 - Wall mounting installation. 5. Align the posts on the wall mount with the holes in back of the JV-35. Slide the phone down on the posts to secure it. C.
Installation Fig.
E N G L I S H Operating your JV-35 A. Dialing Pick up the handset and dial like any other telephone. As you dial, the numbers you are dialing will be announced (Seven, five, two, etc.) If you read Braille, you can use the small bump on the 5 button to help identify correct buttons. You can also use the Braille characters on the buttons to find the letters on each button. For example, the 2 button has Braille characters for A, B and C. B. Making Calls Louder 1.Press the AMPLIFY button.
Operating your JV-35 warning printed in Braille to the back of the handset (See, Diagram A). C. Adjusting The Tone 1. When you hear a voice on the line, press the AMPLIFY button. Diagram A - JV35 handset Note: In standard use, the amplifier turns off whenever you hang up the telephone. This is a useful feature if many people use the phone. If you want the amplifier to always remain on, slide the Volume Reset Override switch on the back of the phone to ON, as shown in Figure 10. Fig.
E N G L I S H Operating your JV-35 Fig. 13 - Ringer Switch Note: When the JV-35 is on HOLD, if you pick up another phone that is on the same line, the JV-35 will automatically hang up. You can continue your call on the other phone. E. Hold 1. To put the phone on hold, press the HOLD button and put the handset in its cradle. The red light in the Ring Flasher shows HOLD is on. F. Last Number Redial E S P A Ñ O L Lift the handset and press the REDIAL button to dial the last number you dialed.
Operating your JV-35 G. Programming The Emergency Buttons The Emergency Buttons can be programmed to dial numbers with one touch. You may wish to use these buttons for police, fire or medical response. 1. Lift the handset and press the PROG button. 3. Press PROG button again. 4. Press one of the Emergency buttons. Fig. 18 - Emergency Button 5. Hang up the handset. Fig. 16 - PROG Button 2. Enter the phone number as you would normally dial it. Fig. 17 - Entering Number 10 6.
E N G L I S H Operating your JV-35 H. Dialing With An Emergency Button 1. Lift the handset. 2. Press one of the Emergency buttons. You will hear an announcement similar to: “Emergency One” and then the number you have stored for that button will be automatically dialed. I. Programming Frequently Dialed Numbers 1. Lift the handset and press the PROG button. 2. Enter the phone number as you would normally dial it. Fig. 20 - Entering Number 3. Press the PROG button again. 4.
Operating your JV-35 7. To change a stored number or to program another memory button, repeat this process from step 1. J. Memory Dialing 1. Lift the handset. 2. Press MEMORY and one of the number buttons. automatically dialed. K. Recording Emergency Button Identification Announcements The JV-35 comes with factory pre-recorded announcements to identify each Emergency button such as “Emergency One” etc.
E N G L I S H Operating your JV-35 beep” sound. This confirms the JV-35 is ready to be programmed. Fig. 22 - Announcement Switch 3. Press the desired Emergency button. After the “beep,” speak into the handset to record an announcement like “Police” or “Fire” for that button. Your recording can be up to three seconds long. 4. After three seconds there will be a “beep” to tell you recording has stopped. Your recording will be played back immediately so you can check it, followed by a “beep-beep” sound. 5.
Operating your JV-35 position and your recordings will be played when you press an Emergency button. Fig. 24 - Custom Announcement L. Recording Memory Button Identification Announcements Factory pre-recorded announcements identify each memory button. You can erase these announcements and record your own announcements, such as “Bob’s Number,” or “Bank.” Record announcements by following these steps. 14 1. Pick up the handset 2. Slide the ANNOUNCEMENT switch to the PROG position.
E N G L I S H Operating your JV-35 “Bank” for that button. Your recording can be up to three seconds long. Fig. 26 - Memory Button 4. After three second there will be a “beep” to tell you recording has stopped. Your recording will be played back immediately so you can check it, followed by a “beep-beep” sound. 5. Now you can repeat steps 3 and 4 if you want to change your announcement or if you want to record an announcement for a different memory button. 6.
Operating your JV-35 number buttons. If you choose, you can record announcements for the number buttons in your own voice by following these steps. 3. Press the 1 button. After the “beep,” say “One” in your own voice or language. Your recording can be up to one second long. 1.Pick up the handset. 2.Slide the ANNOUNCEMENT switch to the PROG position. You will hear “Program Mode, Program Mode” followed by a “beepbeep” sound to confirm the JV-35 is ready to be programmed. Fig. 29 - Keypad Programming 4.
E N G L I S H Operating your JV-35 the rest of the number buttons. 6. When you are finished recording, hang up the handset. 7. Slide the ANNOUNCEMENT switch to the CUSTOM position. Your announcements will be played when you press a number button. Fig. 30 - Custom Announcements N. Selecting Number Button Announcements To hear the number button announcements that were pre-recorded at the factory, slide the ANNOUNCEMENT switch to PRESET. Fig.
Operating your JV-35 To turn off the voice announce feature, turn the phone over and slide the “VOICE ANNOUNCE” switch to OFF. Fig. 33 - Setting Voice Announce O. Direct Audio Connection To connect an assistive listening device, plug a compatible auxiliary cable into the Audio Output port, then plug the other end into your assistive listening device. Fig. 34 - Audio Output port Location 18 When you have an assistive listening device connected, you still must speak into the handset.
E N G L I S H Operating your JV-35 Connecting the Speech Processor: Caution: Before plugging any cord into your speech processor, you must consult your implant manufacturer. WARNING! During thunderstorms, avoid using telephones as electric shock from lightning can occur. • Plug the mono end of the plug into the speech processor. • Plug the stereo end of the plug into the Audio Output socket on the phone. • Speak into the handset when using the cochlear implant adapter cord.
Troubleshooting Chart If any problem should arise during operation of your JV-35, go through the suggestions listed below. Should the difficulty persist, contact Ameriphone or your authorized dealer for assistance. 20 SYMPTOM CAUSE AND CORRECTIVE ACTION No dial tone Check all phone cord connections. No number dialed when memory button pressed No number stored in that memory button.
E N G L I S H Regulatory Compliance Part 68 of FCC Rules Information This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
Regulatory Compliance you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment.
E N G L I S H Regulatory Compliance disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. This telephone equipment is hearing aid compatible. We recommend the installation of an AC surge arrester in the AC outlet to which this equipment is connected.
Regulatory Compliance and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
E N G L I S H Important Safety Regulatory Instructions Compliance Clarity, a Division of Plantronics, Inc. 4289 Bonny Oaks Drive Chattanooga, TN 37406 Telephone: 800-874-3005 Industry Canada Technical Specifications This product meets the applicable Industry Canada technical specifications. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
Important Instructions Regulatory Compliance should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalence Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
E N G L I S H Warranty Ameriphone products are manufactured by Clarity, a Division of Plantronics, Inc. This warranty applies only to Ameriphone products that are purchased and used in the United States or Canada. Clarity warrants the JV-35 telephone against any defect in materials or workmanship for the period of one year from the date of purchase. If your Ameriphone product is defective and returned within 30 days of the date of purchase, your JV-35 dealer will replace it at no charge.
Warranty limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above exclusions or limitations may not apply to you. To get warranty service for your JV-35 phone, you must provide proof of the purchase date. Within 30 days of the date of purchase, return your JV-35 to the place where you purchased it for immediate replacement. After 30 days, call Clarity Customer Service at (800) 426-3738 for the authorized service center nearest you.
E N G L I S H Warranty telephone systems or more sophisticated switching systems. If your JV-35 is not covered by this warranty, call (800) 426-3738 for advice as to whether we will repair your JV-35 and other repair information. The repair shall be warranted for 90 days.
Important Instructions Specifications - JV-35 DECIBEL GAIN Maximum gain: 37dB at 3000Hz (Volume at Maximum setting and Tone at High setting) PHYSICAL DIMENSIONS Size: 9.5" x 7" x 3.25" Weight: 2.52 lbs.
E N G L I S H 31