Installation & Assembly

ManualsBrandsClarke Products ManualsBathroom Remodel & Bathroom FixturesSculptura 60" x 36" Drop in Whirlpool Bathtub

Installation Instructions and Operation Manual

Effective July 30, 2014

Installer: This booklet must be given to the product owner.

Please note important information below:

READ INSTRUCTIONS THOROUGHLY PRIOR TO INSTALLING PRODUCT:

IF YOU HAVE ANY QUESTIONS CALL 1-800-426-8964.

FAILURE TO FOLLOW MANUFACTURERS INSTRUCTIONS WILL RESULT IN YOUR ASSUMPTION OF

PRODUCT LIABILITY AND CAN RESULT IN PRODUCT DAMAGE AND/OR PERSONAL INJURY.

THIS PRODUCT MEETS NATIONALLY RECOGNIZED STANDARDS INCLUDING ANSI Z124.1- 9, ASME A112,

IAPMO AND UL 1795. INSTALLER IS RESPONSIBLE FOR COMPLYING WITH LOCAL CODES THAT MAY

APPLY.

LICENSED PLUMBERS AND ELECTRICIANS SHOULD BE EMPLOYED TO INSURE PROPER INSTALLATION.

INSTALLERS ASSUME ALL LIABILITY FOR FOLLOWING THE CORRECT INSTALLATION PROCEDURES.

Distributor Name:

Model Number:

Manufacture Date:

Chopped By:

Summary of content (14 pages)

PAGE 1
Installation Instructions and Operation Manual Effective July 30, 2014 Installer: This booklet must be given to the product owner. Please note important information below: Distributor Name: Model Number: Manufacture Date: Chopped By: READ INSTRUCTIONS THOROUGHLY PRIOR TO INSTALLING PRODUCT: IF YOU HAVE ANY QUESTIONS CALL 1-800-426-8964. FAILURE TO FOLLOW MANUFACTURERS INSTRUCTIONS WILL RESULT IN YOUR ASSUMPTION OF PRODUCT LIABILITY AND CAN RESULT IN PRODUCT DAMAGE AND/OR PERSONAL INJURY.
PAGE 2
Important Safety Instructions WARNING: When using this product, basic precautions should be followed as noted below: This manual contains information and instructions for proper operation and maintenance of your Clarke bathtub. Failure to follow these instructions could result in personal injury or electric shock.
PAGE 3
SAVE THESE INSTRUCTIONS Table of Contents Unpacking the Unit 3 Electrical Requirements 4 Rough-In Measurements 5 Installation Planning & Preparation 6 Installation Instructions 6 Cleaning Instructions 8 Operating Instructions 9 Repair & Trouble-shooting 10 Warranty 11 Tub Cut-out Measurements & Templates 12 ATTENTION INSTALLER Access should be provided to the whirlpool pump & blower connections and should have a minimum size of 16” x 14” for installation and future servicing of the batht
PAGE 4
Electrical Requirements ALL CONNECTIONS MUST BE GFCI (Ground Fault Circuit Interrupted) PROTECTED 1. Whirlpool and Total Massage units require dedicated 20 Amp, 120V service. 2. You must provide a receptacle with a 20-amp configuration. 3. See local codes for proper wire size. If not specified, use #12 Copper only wire. 4. Optional Factory Installed Heater requires its own dedicated 20 amp service.  The unit must be connected to a circuit interrupter (GFCI) provided by the installer.
PAGE 5
Rough-In Measurements (refer to Illustration C on previous page) Prefix Clarke Name Alexandria Concentra I Concentra II Dara Dara II Elisa Elizabeth Eureka II 6060 Hallmark Heirloom I (RH) Heirloom II Odyssey Original Oval 5 Oval 6 Sculptura III Sparta Sparta Sparta Sparta Sparta Sparta Sparta Skirted Sparta Skirted Stellar Urban Skirted Victoria Victoria II Vida Vida II Vision Skirted + Vision Skirted + Vision Skirted + Vision Skirted + Vision Skirted + Vision Skirted + Vision Skirted Vision Skirted(LH) Wa
PAGE 6
Installation Planning and Preparation 1. 2. 3. 4. 5. BATH TUBS MUST BE SET IN SETTING COMPOUND. An uneven floor can impede installation. NEVER LIFT THE TUB BY THE PLUMBING. Doing so can result in leaks. Check if the floor is level and of good quality. An uneven floor may impede proper installation of the product. The floor structure must be capable of supporting a minimum of 80 pounds per square foot. Clean the area of any debris or trash. Use a 5 or 6-foot level to determine if the floor is level.
PAGE 7
aid in properly setting the tub. 7. Verify that the product is level by checking the tub deck surface in all directions. 8. Options A: (Whirlpools with Air on/off Switches only) Plug the pump cord into the dedicated 120V/20A GFCI outlet to supply electrical power to the system. The cord is attached to the pump & is shipped with the system. Options B: (Air Massage with 3 button control only) Plug the blower cord into blower control box.
PAGE 8
Installing an Oval Tub with a Template Diagram Refer to page 13. The back section of this manual contains oval cut out instructions. Use pencil and tape measure to plot the coordinates and draw the cut out. Take special care that you do not to drop the tub in the platform cutout, since the tub may break and the ensuing warranty limitations would become effective. For additional questions on installing the tub read “installation procedures” above.
PAGE 9
Operating Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. Fill the bath at least to 3 inches above the jets before activating the pump. The air bath blower and/or whirlpool pump is activated by depressing the control panel buttons. Do not repeatedly depress the switch in rapid order if you do not see the whirlpool function right away, as it may take a few seconds before you can see it fully operating. Please see air bath control or Total Massage Control instructions below for operation and features.
PAGE 10
Whirlpool Troubleshooting MOTOR WILL NOT START Troubleshooting Pump or Blower – initial check 1. 2. 3. 4. 5. Check circuit breaker at electric box –make sure that it has not tripped. Make sure that it is a size 20 amp circuit breaker, with nothing else tied to this circuit. Check to make sure the heater on its own 20 amp circuit breaker & GFIC plug. Check GFIC outlet – make sure that it has not tripped. Reset if necessary.
PAGE 11
SAVE THESE INSTRUCTIONS This product and its components are ETL listed and IAPMO approved TWO YEAR LIMITED WARRANTY All Clarke Products Whirlpools and Bathing Systems are warranted in accordance with the following Limited Warranty: Clarke Products Whirlpools and Bathing Systems are warranted against defects in material and workmanship for a period of two (2) years from the date of the first consumer purchase.
PAGE 12
Tub Cut-Out Templates Use for Item #’s: Oval 5 3858 Use for Item #’s: Oval 6 4071 (this tub can be under-mounted or drop-in installed) 12
PAGE 13
Under-mount or flush mount dimensions on Sparta Drop in Units only: For Drop-in installation on Sparta 3672: cut out size is 70” long x 34”wide, ¼” radius corners. For Drop-in installation on Sparta 3666: cut out size is 64” long x 34”wide, ¼” radius corners. For Drop-in installation on Sparta 3660: cut out size is 58” long x 34”wide, ¼” radius corners. Drop-in dimensions on the Heirloom: For Drop-in installation on Sparta 3260: cut out size is 58” long x 30”wide, ¼” radius corners.
PAGE 14
Tub Cut-Out Templates – cont. Use for Item #’s: Heirloom 4260HL Use for Item #’s: Heirloom 4272HL Use for Item #’s: Stellar 4472ST Please note: Odyssey RC6060SK comes standard with attached skirt. It is not designed to be drop-in. Use for Item #’s: Eureka II C6060 Measure a 60” square – come out from point of one corner & measure 61” – that is front of tub.  61”length~58” cut out”  For corner template: drop-in  85” length~82” cut out  The front deck is 48 5/8” in width.