CFP-130, CFP-170, CFP-200 CFP-1700, CFP-1700DS CFP-2000, CFP-2000DS Polisher Operator’s Manual / Manual del operador / Manuel de l’utilisateur MODELS: 01281A, 01280A, 01310A, 01320A, 01350A, 01431A, 01360A, 01390A, 01400A, 01401A, 01430A READ THIS BOOK EN LEA ESTE MANUAL ES LISEZ CE MANUEL FR English (2 - 11) Español (12 - 21) Français (22 - 30) This book has important information for the use and safe operation of this machine.
ENGLISH EN revised 9/11 CONTENTS OF THIS BOOK Important Safety Instructions .............................................................................................. 3 Introduction ......................................................................................................................... 4 Accessories ........................................................................................................................ 5 Machine Specifications .........................................
ENGLISH EN OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner’s Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner’s Manual and on your machine.
ENGLISH EN WARNING: Use of this machine as a step or furniture could result in injury or damage. Do not use this machine as a step or furniture. Do not ride on this machine. WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this machine. WARNING: Injury to operator or bystanders could occur if an abrupt change in floor surface texture is encountered when using this machine.
ENGLISH EN ACCESSORIES 5. Synthetic pads for polishing, scrubbing, stripping and spray buffing. The following accessories are available. 1. Polishing and waxing brushes. 6. Brushes with metal or wood backs and with holes to let the solution flow through. 2. Brushes with natural or synthetic bristles for scrubbing. 7. Solution tank. 3. Brushes with steel wire bristles. 8. Sanding discs. 4. Synthetic pad holders. 9. Solution Buff Accessory. Model CFPSolution Tank Assembly Weight Kit (10 lb.
ENGLISH EN Machine Specifications Model Part Number Voltage (Volts) Frequency (Hz) Current (Amps) Pad /Brush Speed Pad/Brush Size Power Gearbox Cord Length Handle Tube Main Frame Height w/handle Weight w/cord CFP 130 01281A 120 60 12.6 175 rpm 13” (33 cm) 1 hp (0.75 kW) 2 - Planet 50’ (15 m) Tubular Steel Die Cast Aluminum 46” (117 cm) 81 lbs. (36.
ENGLISH EN HOW TO PREPARE THE MACHINE FOR OPERATION 1 UNCRATE THE MACHINE When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected. Contact the Clarke Customer Service Department.
ENGLISH EN 120 VOLT MACHINES Instructions for connection to the power supply and the electrical ground. This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and grounding plug.
ENGLISH EN HOW TO OPERATE THE MACHINE OPERATION (Figure 4) 1 2 3 Unwrap the Power Cord (5) and plug it into a properly grounded outlet. Pull up on the Handle Release Compression Lever (4). Move the Operator Handle (6) downward until your arms are almost straight. Push down on the Handle Release Compression Lever (4) to lock it in place. Lift up on the Operator Handle (6) until the brush (or pad) is flat against the floor. 1 3 2 WARNING! Be prepared to control the machine as soon as the motor starts.
ENGLISH EN TROUBLESHOOTING SWIRLS ON THE FLOOR AFTER SCRUBBING • Floor not clean. • Incorrect solution. • Area not properly swept - debris in pad or brush. • Improper pad or brush for the job. • Moving the machine too fast. SWIRLS ON THE FLOOR AFTER DRY BUFFING • Moving the machine too fast. • Floor finish too soft. • Area not properly swept - debris in pad or brush. • Improper pad or brush for the job. CIRCLES ON THE FLOOR • Machine standing still while the brush or pad is running.
ENGLISH EN NOTES Clarke® Operator's Manual (EN) - CFP Polisher FORM NO.
ESPAÑOL ES revised 9/11 LIBRO DE INSTRUCCIONES LEA ESTE LIBRO CUIDADO: Lea el Libro de Instrucciones antes de usar este aparato. Contiene información importante para el uso y funcionamiento correcto y seguro de la máquina. Lea este libro completamente antes de arrancar la máquina o hacer cualquier operación de mantenimiento. Si non sigue las instrucciones, corre el peligro de herirse o causar lesiones al personal, o causar daños importantes a la máquina o a su entorno.
ESPAÑOL ES INSTRUCCIONES PARA LA SEGURIDAD DEL OPERADOR WARNING AVERTISSEMENT ¡ AVISO ! ¡ PELIGRO ! : Si no sigue la indicación PELIGRO, se pueden causar lesiones graves, incluso mortales. Lea y siga todas las indicaciones PELIGRO que se encuentran en el libro y en la máquina. ¡ AVISO ! : Si no sigue la indicación AVISO, se pueden causar lesiones sea al operador sea a otro personal y/o daños materiales. Lea y siga todas las indicaciones AVISO que se encuentran en el libro y en la máquina.
ESPAÑOL ES ¡ AVISO ! Use siempre un cable con tres conductores puestos a tierra. Para una protección óptima, conecte la máquina con una caja de enchufe conectada con la red que tiene un diferencial. Si tiene alguna duda, sírvase acudir a un eléctrico cualificado. ¡ AVISO ! Para evitar daños al cable de alimentación, procure que el cepillo, el disco, el portadisco o las ruedas no toquen el cable, cuando la máquina funciona. Levante siempre el cable por encima de la máquina.
ESPAÑOL ES ACCESORIOS Los accesorios siguientes son disponibles : 1. Cepillos para encerar y pulir. 2. Cepillos para fregar con filamentos en fibras naturales o sintéticas. 3. Cepillos de alambre de acero. 4. Portadiscos sintéticos. 5. Discos sintéticos para pulir, fregar, decapar y lustrar con tampón. Model CFPConjunto de depósito de solución Juego de pesas (10 lb.
ESPAÑOL ES Especificaciones de la pulidora Modelo Número de código Tensión (V) Frecuencia (Hz) Corriente (A) Velocidad de la almohadilla/el cepillo Tamaño de la almohadilla/el cepillo Potencia Transmisión Longitud del cable Tubo de la manija Base Peso con manija Peso (con cable) CFP 130 01281A 120 60 12.6 175 rpm 13” (33 cm) 1 hp (0.75 kW) 2-Engranaje planetario 50’ (15 m) Acero tubular Alumminio fundido a presión 46” (117 cm) 81 lbs. (36.
ESPAÑOL ES PREPARACION DE LA MAQUINA PARA TRABAJAR 1 DESEMBALAJE DE LA MÁQUINA Cuando reciba la màquina, inspeccione con cuidado la caja de embarque y la máquina, para verificar si hay algún daño. Si hay algún daño evidente, guarde la caja de embarque de modo que se la pueda inspeccionar. Comuníques con el Departamento de Atención al Cliente de Clarke.
ESPAÑOL ES MAQUINAS 120 V. INSTRUCCIONES PARA LA CONEXION ELECTRICA DE LA MAQUINA La máquina debe ser puesta a tierra. En caso de mal funcionamiento o de avería, el hilo de tierra es un camino de menor resistencia que permite el paso de corriente ; por lo cual se reduce el riesgo de choque eléctrico. La máquina tiene un cable de alimentación con tres conductores y un enchufe con tres clavijas de las cuales una está puesta a tierra.
ESPAÑOL ES FUNCIONAMIENTO DE LA MAQUINA FUNCIONAMIENTO (Figura 4) 1 2 3 Desenrolle el cable de energía (5) y enchúfelo en una toma con adecuada conexión a tierra. Tire de la palanca de compresión para aflojar la manija hacia arriba (4). Mueva la palanca del operador (6) hacia abajo hasta que sus brazos estén casi rectos. Empuje hacia abajo sobre la palanca de compresión para aflojar la manija (4) para fijarla en su lugar.
ESPAÑOL ES DETCCIÓN DE PROBLEMAS REMOLINOS EN EL PISO DESPUÉS DE LA LIMPIEZA • El piso no está limpio. • La solución no es adecuada. • El área no está adecuadamente barrida - hay suciedad en la almohadilla o el cepillo. • Uso de almohadilla o cepillo incorrecto para la tarea. • La máquina se desplaza demasiado rápido. REMOLINOS EN EL PISO DESPUÉS DEL PULIDO EN SECO • La máquina se desplaza demasiado rápido. • El acabado del piso es demasiado blando.
ESPAÑOL Clarke® Manual del operador (ES) - CFP Polisher ES FORM NO.
FRANÇAIS FR revised 9/11 MANUEL D’UTILISATION LISEZ CE MANUEL ATTENTION: Lire le manuel d’utilisation avant de faire fonctionner l’appareil. Il contient des informations importantes pour une utilisation correcte de la machine, en toute sécurité. Lisez-le complètement avant de mettre la machine en marche ou d’effectuer un entretien. A défaut, vous risqueriez de vous blesser ou de blesser d’autres membres du personnel, d’endommager sérieusement la machine ou de provoquer des dégâts dans son environnement.
FRANÇAIS FR INSTRUCTIONS POUR LA SECURITE DE L’OPERATEUR WARNING AVERTISSEMENT ¡ AVISO ! ! DANGER ! Le non-respect des consignes précédées du mot DANGER peut occasionner des blessures graves, voire entraîner la mort. Lisez et respectez toutes les consignes DANGER figurant dans ce manuel et sur la machine. AVERTISSEMENT Le non-respect des consignes AVERTISSEMENT peut entraîner des blessures pour l’opérateur ou d’autres membres du personnel et/ou occasionner des dégâts matériels.
FRANÇAIS FR AVERTISSEMENT Utiliser toujours un câble à trois conducteurs, relié à la terre. Pour une protection optimale, branchez la machine sur une prise réseau équipé d’un différentiel. En cas de doute, veuillez faire appel à un électricien qualifié. AVERTISSEMENT Pour éviter d’endommager le câble d’alimentation, veillez à ce que la brosse, le disque, le portedisque ou les roues ne touchent pas le câble, lorsque la machine fonctionne. Soulevez toujours le câble au-dessus de la machine.
FRANÇAIS FR ACCESSOIRES Les accessoires suivants sont disponibles: 1. 2. 3. 4. 5. Brosses pour cirer et polir Brosses de récurage, avec brins en fibres naturelles ou synthétiques. Brosses avec brins en acier Porte-disques synthétiques Disques synthétiques pour le polissage, le récurage, le décapage et le lustrage au tampon. Modèle CFP Ensemble de réservoir de solution Poids du Kit (10 lb.
FRANÇAIS FR Spécifications de la cireuse de CFP Modèle Numéro de code Tension (volts) Fréquence (Hz) Courant (Amps) Vitesse du patin/brosse Tailee du patin/brosse Puissance Transmission Longueur du câble Tube poignée Base Hauteur avec poignée Poids (avec câble) CFP 130 01281A 120 60 12.6 175 rpm 13” (33 cm) 1 hp (0.75 kW) 2-étages planétaires 50’ (15 m) Acier tubulaire Aluminium moulé 46” (117 cm) 81 lbs. (36.
FRANÇAIS FR PREPARATION DE LA MACHINE AVANT LA MISE EN SERVICE DÉBALLER LA MACHINE 1 Lorsque la machine vous est livrée, contrôlez minutieusement que la boîte d’emballage et la machine ne présentent aucun dommage. Si elles sont endommagées, conservez la boîte d’emballage afin qu’elle puisse être inspectée. Contactez immédiatement le service d’entretien Clarke.
FR FRANÇAIS MACHINES 120 V. INSTRUCTIONS POUR LE RACCORDEMENT ELECTRIQUE Cette machine doit être mise à la terre. En cas de dysfonctionnement ou de panne, le fil de terre constitue un chemin de moindre résistance qui permet le passage du courant, réduisant ainsi le risque de choc électrique. La machine est munie d’un câble d’alimentation à trois conducteurs et d’une fiche à trois broches, dont une sert à la mise à la terre.
FRANÇAIS FR MISE EN SERVICE DE LA MACHINE FONCTIONNEMENT (Figure 4) 1 2 3 Désenroulez le câble d’alimentation (5) et branchez-le à une prise correctement mise à la terre. Tirez sur le levier de dégagement de la poignée (4). Appuyez sur la poignée de l’opérateur (6) vers le bas jusqu’aux vos bras soient presque droits. Appuyez sur le levier de dégagement de la poignée (4) pour le bloquer fermement en place.
FRANÇAIS FR DIAGNOSTIC TRACES SUR LE SOL APRÈS RÉCURAGE • Le sol n’est pas propre. • Solution incorrecte. • Le zone n’a pas été correctement balayée - débris sur le patin ou la brosse. • Patin ou brosse incorrect pour la tâche. • Déplacement trop rapide de la machine. TRACES SUR LE SOL APRÈS NETTOYAGE A SEC • Déplacement trop rapide de la machine. • Finition du sol trop souple. • La zone n’a pas été correctement balayée-debris sur le patin ou la brosse. • Patin ou brosse incorrect pour la tâche.
CFP Series 120V & 230V Section II Parts and Service Manual (70880A) Clarke® Operator's Manual- CFP Polisher FORM NO.
revised 9/11 ASSEMBLY 1 3 2 5 14 4 29 13 7 6 14 10 23 11 8 9 22 12 25 24 19 21 28 17 20 16 15 26 18 27 - 32 - FORM NO.
revised 9/11 ASSEMBLY Item 1 2 3 4 5 6 7 [] [] 8 9 10 [] [] [] 11 12 13 14 Ref. No.
Clarke® CFP-130,170, 1700, 200, 2000 Motor Assembly Drawing, Parts List and Schematics 3/08 RUN START MODEL CFPVOLTS / Hz MOTOR PART NUMBER Part No. Description 40693A 53193A 40694A 40695A 53191A 40696A 53189A 40697A 53360A 40698A 40699A 53190A 53195A 40899A 70787A 80274A 85303A 902550 53848A 80141A 911177 41053A 747553 Page - 34 - 70880A Rotor, 1HP, 60Hz Rotor, 1.5HP, 60Hz Capacitor, Start Capacitor, Run Capacitor, Run Stator, 1HP, 60Hz Stator, 1.
Clarke® CFP-130, 170, 1700, 200, 2000 Gearbox Assembly Drawing & Parts List 7/07 4 14 13 9 5 17 11 13 7 16 8 16 2 3 15 18 13 10 6 12 MODEL CFPVOLTS / Hz GEARBOX PART NUMBER Ref. Part No.
revised 9/11 CFP-1700DS, 2000DS Motor Assembly and Schematic MOTOR 40764A 2 Item 15 14 4 6 6 10 16 18 9 8 6 6 20 19 7 99 17 7 12 13 11 2 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20# 21 NI NI Ref. No. Qty Description N/A 912287 448396 51405A 51435A 962546 980608 902606 902550 40322A N/A N/A 55648A 980076 55647A 59606A 56039285 53849A 80141A 40851A Commutator Bracket Rectifier, Bridge Spring (Included with #8) Brush Asm., (Included w/#8) Brush Board Asm.
Clarke® CFP-1700DS, 2000DS Gearbox Assembly Drawing & Parts List 7/07 18 17 16 4 11 4 12 10 8 13 14 13 15 9 7 6 4 5 3 1 GEARBOX 53647A Ref 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 NI Part No.
14600 21st Avenue North Plymouth, MN 55447-3408 www.clarkeus.com Phone: 800-253-0367 Fax: 800-825-2753 ©2011 Nilfisk-Advance, Inc.