E Operator's Manuals Vision 17B/BT (click here) Vision 17E 115V (click here) Vision 17E 230V (click here)
E Operator's Manual Vision 17B/BT READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Table of Contents Operator Safety Instructions ............................................................................................... 3 Introduction & Machine Specifications ................................................................................ 5 Procedures for Transporting Machine ................................................................................. 6 Machine Controls & Features .............................................................................................
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
Page -4- WARNING: Machines can topple over if guided over the edges of stairs or loading docks and cause injury or damage. Stop and leave this machine only on a level surface. When you stop the machine, put all switches into their "OFF" position. WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized Clarke Technology personnel only.
Introduction & Machine Specifications The newly designed Vision 17 automatic scrubber increases labor efficiency while providing superior cleaning. This unit dispenses the solution, scrubs the floor and then recovers the soiled solution all in one pass. The Vision 17 is available in four models. The four models are battery versions, one a standard battery and the other a battery version with traverse and each with parking brake as standard.
PROCEDURES FOR TRANSPORTING How to Put the Machine Into a Van or Truck WARNING: This machine is heavy. Get assistance before attempting to transport or move. Use two able persons to move the machine on a ramp or incline. Always move slowly. Do not turn the machine on a ramp. Do not stop and leave the machine on a ramp or incline. To load the machine into a van or truck follow this procedure: 1. Remove the squeegee and the brush (see "How to Prepare Machine for Operation"). 2.
MACHINE CONTROLS and FEATURES Brush Switch. See Figure 1. The brush switch is to the left of the vacuum switch on the control panel. To start the brush motor, press the top of the switch. To stop the brush motor, press the bottom of the switch. Figure 1 Vacuum Switch. See Figure 2. The vacuum switch is to the left of the solution control knob. To start the vacuum motor, press the top of the switch. To stop the vacuum motor, press the bottom of the switch. Solution Control Knob. See Figure 3.
MACHINE CONTROLS and FEATURES (cont'd) Voltmeter. See Figure 5. This gauge indicates the amount of power in the batteries. If the reading is in the lower area of the meter, the battery voltage is low. See the section of this book called "Maintenance". Figure 5 Brush Control Pedal. See Figure 6. The brush control pedal is at the back of the machine in the lower right corner. Use your foot to operate the pedal. To lower the brush, push the pedal down and to the left, releasing it from the locked position.
MACHINE CONTROLS and FEATURES (cont'd) Traverse Speed Control. See Figure 10 The traverse speed is controlled by a variable speed knob. Turn the knob clockwise to increase speed. Brush Pressure Adjustment. Figure 10 The brush pressure can be adjusted for normal cleaning or for stripping. Locate the knob on the rear of the brush motor. To access motor, turn off the key, remove the squeegee cable and undo tank clamps. Turn the knob clockwise to increase brush pressure (strip mode).
MACHINE CONTROLS and FEATURES (cont'd) Key Switch. See Figure 14. The battery traverse model has a key switch located on the back side of the control panel. The key switch must be turned to the on position (I) to activate the traverse. The key may be removed for security purposes from the off position (O). The Parking Brake. The brake prevents the movement of the machine. The brake pedal is at the back of the machine in the lower left corner. To activate the brake, push the pedal down.
HOW TO PREPARE THE MACHINE FOR OPERATION How to Install the Squeegee Connection TUBE The proper method for assembling the squeegee connection is as follows:: NUT GASKET 1. Unscrew the nut completely. ELBOW 2. Slide the nut and gasket onto the tube. (Figure 1a) 3. Slide the elbow onto the tube and make sure the gasket is secured into the elbow. (Figure 2a) 4. As you hold the elbow tight onto the tube, tighten the nut over the gasket and the elbow.
HOW TO PREPARE THE MACHINE FOR OPERATION (cont'd) 8. To remove a brush or pad driver, turn the pad driver or brush to the left and remove. 9. Lift up the machine with the lift handle and return the support leg to its normal position. CAUTION: Leaving the brush motor switch in its "DOWN" position when the machine is not in use can damage the brush or pad driver. Always leave the brush motor in the "UP" position while not in use.
HOW TO OPERATE THE MACHINE Filling the Solution Tank To fill the solution tank, follow this procedure: 1. Lift the solution tank lid out of the opening. Allow the lid to hang to the front of the machine. See figure 21. 2. With a hose or bucket fill the solution tank with clean water to within one inch of the bottom of the opening. 3. Add a cleaning chemical to the water. For the correct amount, follow the manufacturer's directions shown on the chemical container. Figure 21 4.
HOW TO OPERATE THE MACHINE (cont'd) 8. To turn the machine, push the rear of the machine to the side opposite the direction you want to turn. It is NOT RECOMMENDED that you move the machine backward during a cleaning operation. 9. When you make more passes across the floor, let the brush clean approximately 2 inches of the area already cleaned by the last pass. NOTE: During most cleaning procedures, apply and remove the solution in one operation.
MAINTENANCE DANGER: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be done by authorized Clarke Technology personnel only. DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before operation. Keep all fasteners tight. DANGER: Wearing jewelry such as watches, rings, etc.
MAINTENANCE (cont'd) Procedures to be Performed Before Work is Begun Keep the machine clean. It will need fewer repairs and have a longer life. 1. Unplug charger from the wall. 2. Disconnect the connector on the battery charger from the connector on the batteries. See figure 23. 3. Figure 23 Join the connector from the batteries to the connector on the tank support. See figure 24. 4. Make sure the recovery tank cover is in place. 5. Check the solution tank screen and clean if necessary. See figure 25. 6.
MAINTENANCE (cont'd) 3. Leave the tanks and the drain hoses open to dry in the air. 4. Check and clean the squeegee blade. Use a soft cloth to clean the squeegee blade. If the squeegee blade is damaged or worn, turn or replace the blade. 5. Check and clean the vacuum gaskets, the vac screen filter and the solution screen filter. Remove and clean with a vinegar-water solution or warm soapy water. Rinse the parts in clean water.
MAINTENANCE (cont'd) Weekly Maintenance Use a grease gun to lightly lubricate the drive wheels and casters. Access to the drive wheels is through the access hole in the skirt. Access to the casters is from the rear of the machine. Battery Maintenance The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventative maintenance. WARNING: Working with batteries can be dangerous. Always wear eye protection and protective clothing when working near batteries.
MAINTENANCE (cont'd) 2. Keep the tops of the batteries clean and dry. Keep the terminals and connectors clean. To clean the top of the batteries, use a damp cloth with a weak solution of ammonia or bicarbonate of soda solution. To clean the terminals and connectors, use a terminal and connector cleaning tool. Do not allow ammonia or bicarbonate of soda to get into batteries. 3. Keep the batteries charged.
CLARKE TECHNOLOGY Vision 17B Machine Variables VVision 17 BT Vision 17B CODE NUMBER 00380E 00381A 00381B 00382A 00382B 00383A Serial # ... to XE 00383A Serial # XE to ... 00383B Serial # ... to XE 00383B Serial # XE to ... 00384B Serial # ... to XE 00384A Serial # ... to XE 00384A Serial # XE to ... 00384B Serial # XE to ... 00390E 00391A 00391B 00392A 00392B 00393A Serial # ... to XE 00393A Serial # XE to ... 00393B Serial # ... to XE 00393B Serial # XE to ... 00394A Serial # ...
CLARKE TECHNOLOGY Vision 17B Machine Accessories 5/99 Accessories: Part No. 51436B 53126B 50527A 56927A 50477A 962819 51437B 51439B 682408 674114 639804 638828 638856 51469B 51481A 10773A 14661B 18800A Description Brush, Polypropylene Pad Driver Big Mouth Base Big Mouth Retainer Clutch Plate for Pad/Brush Clutch Plate Screws Nylon Scrub Brush .028 Dia.
NOTESS Page -22- CLARKE TECHNOLOGY Operator's Manual -Vision 17B/BT
Vision 17B/BT Section II Parts and Service Manual (78454B) CLARKE TECHNOLOGY Operator's Manual - Vision 17B/BT Page -23-
HOW TOO CORRECT PROBLEMS IN THE MACHINE PROBLEM There isn't any solution flow. The solution flow does not stop. The machine does not remove any water from the floor. The machine does not remove all the water from the floor. ACTION CAUSE The solution tank is empty. Fill the solution tank. The solution knob is turned too far to the left. There is an obstruction in the hose or filter. Turn the solution knob to the right. Remove the obstruction from hose or filter.
NOTESS CLARKE TECHNOLOGY Operator's Manual - Vision 17B/BT Page -25-
CLARKE TECHNOLOGY Vision 17B Machine #00380B, 24V Battery, Machine Assembly - 3/00 Page -26- CLARKE TECHNOLOGY Operator's Manual -Vision 17B/BT
CLARKE TECHNOLOGY Vision 17B-Batery Model 24V Battery Machine Assembly Parts List - 3/00 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 NI NI NI NI NI Part No.
CLARKE TECHNOLOGY Vision17 BT Model #00390A, 24V Battery Machine Assembly Drawing - 3/00 Page -28- CLARKE TECHNOLOGY Operator's Manual -Vision 17B/BT
CLARKE TECHNOLOGY Vision 17 - BT Model 24V Battery Machine Assembly Parts List - 3/00 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Part No.
CLARKE TECHNOLOGY Vision 17B ASM, Non Traverse Axle Drawing & Parts List 11/98 Form #10510A 4 6 3 1 2 1 1 3 1 5 6 4 Ref 1 2 3 4 5 6 Part No. 87613A 61247A 59936C 54014A 60196A 87039A Description Washer, Nylon 5/8 Bracket, Axle Wheel Fitting, Grease, ¼"-20 Shaft Washer, Fender ¼" SS Qty 7* Nominal 1 2 2 1 2 NOTE: Place washers as required to center the wheels (Number of washers may vary) NOTE: Grease wheels once a week.
CLARKE TECHNOLOGY Vision 17BT ASM, Traverse Axle Drawing & Parts List 11/98 Form #10512A Repair Parts for 59935C Wheel: Part No. Description 58154A Seal 51187A Roller Clutch Bearing Qty. 2 2 Repair Parts for 59935B Wheel: Part No. Description 58146A Seal 51187A Roller Clutch Bearing Qty. 2 2 Ref 1 *2 3 4 5 6 7 8 Qty 2 10 2 1 1 2 1 2 Part No.
CLARKE TECHNOLOGY Vision 17B/BT Brush Lift Drawing Assembly & Parts List 11/98 Form #16608A 2 5 4 5 3 3 4 2 1 Ref 1 2 3 4 5 Page -32- Part No.
CLARKE TECHNOLOGY Vision 17B/BT ASM, Main Frame Drawing & Parts List - 11/98 Form #16926B Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Part No. 60021A 84239A 53618A 64456A 87026A 85384A 85395A 64505A 85822A 31227A 66960A 38009A 980442 68733B 81104A 52117A 920110 52047A 69028A 85391A 60698A 170915 722021 87614A Description Qty Weldment, Main Frame 1 6 Screw 5/16-18 x 1 Flat Hd SS 1 Adapter 3/8 X 3/8 Handle 1 Washer, S.S.
CLARKE TECHNOLOGY Vision 17B/BT Brush Motor Assembly Drawing and Parts List 3/00 Form #17116A Ref 1 2 3 4 5 6 7 8 9 Part No. 47710A 762005 60670B 44809A Page 43 Page 42 915102 81104A 980662 67865A 63600A Page -34- Description Terminal, Brush Motor Clamp Bracket Gear Motor 24V DC Motor Parts Breakdown Gear Parts Breakdown Key (included with #4) Nut, ¼ - 20 Nylock Washer Spacer, Tilt Handle Guide RH Qty 2 1 1 1 1 2 1 1 1 Ref 10 11 12 13 14 15 16 17 18 19 20 Part No.
CLARKE TECHNOLOGY Vision17B Panel Assembly Non-Traverse Model Drawing & Parts List 11/98 Form # 17641A Ref 1 2 3 4 Part No.
CLARKE TECHNOLOGY Vision 17BT Panel Assembly - Battery Traverse Model Drawing and Parts List 11/98 Form #17640A Ref 1 2 3 4 5 6 7 Page -36- Part No. 44405A 47380A 47304A 69806B 47316B 55413A 54349A Description Meter, Battery Switch, Key (Incl.
CLARKE TECHNOLOGY Vision 17B/BT Squeegee Assembly Drawing & Parts List 11/98 Form #18809A 2 4 1 3 8 7 6 1 5 Ref 1 2 3 4 5 6 7 8 Part No. 66921B 30902A 27703A 30903A 85398A 838201 839702 962841 Description Retainer, Squeegee Blade, Squeegee Rear Squeegee, Casting Blade, Squeegee Front Screw ¼ - 20 X ½ Spacer, Wheel Guide Wheel, Brush Guide Screw, 5/16 - 18 x 1¼ Blades Available: 30918A Blade, Sq., Front Nitrile/EPDM 30919A Blade, Sq.
CLARKE TECHNOLOGY Vision 17B/BT Solution Tank Assembly Drawing & Parts List 6/01 Form #19169A 25 10 26 2 1 3 16 11 23 22 31 15 28 14 29 24 30 4 17 24 33 36 5 10 32 34 13 19 20 21 35 6 12 7 37 8 18 9 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part No.
CLARKE TECHNOLOGY Vision 17B/BT Recovery Tank Assembly Drawing & Parts List 6/01 Form #19170A 1 2 5 4 6 7 20 18 8 19 3 10 17 16 11 4 11 13 12 14 15 Ref 1 2 3 4 5 6 7 8 10K 11 12 Part No.
CLARKE TECHNOLOGY Vision 17B Support Tank Assembly Drawing & Parts List 11/98 Form #18909B Ref 1 3 4 5 6 7 8 9 10 11 12 13 15 16 17 18 19 NI Page -40- Part No.
CLARKE TECHNOLOGY Vision 17BT Support Tank Assembly Drawing & Parts List 11/98 Form #18915B Ref 1 3 4 5 6 7 8 9 10 11 12 14 15 17 18 19 20 21 22 NI Part No.
CLARKE TECHNOLOGY Vision 17BT Brake Kit #10773A Drawing & Parts List 5/98 2 1 3 11 10 4 2 4 5 5 6 7 8 9 Ref # 1 2 3 4 5 6 7 8 9 10 11 Page -42- Part No. 66536A 87027A 17519A 87036A 85397A 67422A 87613A 67133A 10735A 608340 Ref. Description Pin, Brake Washer Brake, Pad Weldment Washer, #10 S.S. Screw, 10-24 x 3/8 S.S. Shaft, Brake Washer, Nylon Rod, Brake Pedal, Brake Spring, Brake Machine Frame Qty 2 2 1 2 2 1 2 1 1 1 ref.
CLARKE TECHNOLOGY Vision 17B/BT Vacuum Motor Drawing & Parts List 11/93 Form #44917A Ref # 1 2 *3 4 5 6 7 *8 9 *10 11 *12 13 Part No.
CLARKE TECHNOLOGY Vision 17B/BT Gear Box #54238A Drawing & Parts List 6/94 9 8 7 6 5 4 3 2 1 Ref 1 2 3 4 5 6 7 8 9 NI Page -44- Part No.
CLARKE TECHNOLOGY Vision 17B/BT Brush Motor Drawing & Parts List 3/95 Form #10503A 13 7 12 12 1 13 2 SEAM LOCATION 3 14 16 4 15 5 17 6 8 9 10 11 Item 1 2 3 4 5 Part No. 56478A 50142A 902654 902550 51840A 6 7 8 9 10 11 12 13 14 15 16 17 50520A 56480A 962546 50517A 448396 40826A 55657A 55656A 59805A 50515A 44809A 54238A Description Stator Frame Assembly (w/Magnets & Clips) Armature Assembly (w. B.E. & F.E. Bearings) Bearings B.E. Bearing F.E.
CLARKE TECHNOLOGY Vision 17BT Traverse Motor Drawing & Parts List 2/96 Motor #45031A Shaft Sub Assembly Instructions View from plain er. schematic Black 8 36 1. Assemble the retaining ring (24) to the output shaft (22) centering the middle tab of the "E" ring in the keyway. The center tab should bottom in the keyway. 25 23 8 22 Red 2. Assemble the key (25) to the output shaft (22) butting the key against the center tab of the retaining ring (24). Dimensions over the key and shaft is .381. 3.
CLARKE TECHNOLOGY Vision 17BT Traverse Motor 24V Drawing & Parts List 2/96 Form #45031C Ref 1 2 3 4 5 6 7 8 9 10 Part No. 40831A 55412A 58152A 54370A 54416A N/A 52060A 47905A 47905A NI Description Carbon, Brush Key Shaft, Seal Gasket, O'Ring Gear Assembly Gear Housing Cap, Gear Head Terminal, ¼ FIFQD Terminal, ¼ FIFQD 1.9 oz.
CLARKE TECHNOLOGY Vision 17B/BT Battery Charger Drawing & Parts List 11/93 Alternate WARNING: All electrical repairs must be performed by qualified personnel only. Charger #40510A: 24 Volt, 10 Amp D.C., 115 Volt A.C., 60 Hz Charger #40511A: 24 Volt, 10 Amp D.C., 230 Volt A.C., 50 Hz Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 Page -48- Description Charger Case Transformer Electronic Controller Kit Capacitor 660 V.A.C. Heat Sink Assembly Ammeter Fuse Holder (2) Cartridge Fuse (2) Strain Relief, A.C.
CLARKE TECHNOLOGY Vision 17B Model #00380A - 24 V Electrical Schematic 8/98 CLARKE TECHNOLOGY Operator's Manual - Vision 17B/BT Page -49-
CLARKE TECHNOLOGY Vision 17BT Model #00390A - 24 V Electrical Schematic 8/98 Page -50- CLARKE TECHNOLOGY Operator's Manual -Vision 17B/BT
CLARKE TECHNOLOGY Vision 17B 24V Connection Diagram 6/01 CLARKE TECHNOLOGY Operator's Manual - Vision 17B/BT Page -51-
CLARKE TECHNOLOGY Vision 17BT 24V Connection Diagram 6/01 Page -52- CLARKE TECHNOLOGY Operator's Manual -Vision 17B/BT
ALTO® PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St. Louis, Missouri 16253 Swingley Ridge Road, Suite 200 Chesterfield, Missouri 63017-1725 PRODUCTION FACILITIES ALTO U.S. Inc., Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 ALTO U.S. Inc., Bowling Green, Ohio 43402 1100 Haskins ALTO U.S. Inc., Clearwater, Florida 33765 1500 N.
CLARKE TECHNOLOGY U.S. LIMITED WARRANTY This Clarke Technology Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke Technology's Maintenance and Operations instructions.
E Operator's Manual Vision 17E 115V READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Table of Contents Operator Safety Instructions ................................................................................... Introduction & Machine Specifications .................................................................... Grounding Instructions 115V................................................................................... Procedures for Transporting Machine ..................................................................... Machine Controls & Features .............................
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
WARNING: Machines can topple over if guided over the edges of stairs or loading docks and cause injury or damage. Stop and leave this machine only on a level surface. When you stop the machine, put all switches into their "OFF" position. WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized Clarke personnel only.
Introduction & Machine Specifications The Vision 17 automatic scrubber increases labor efficiency while providing superior cleaning. This unit dispenses the solution, scrubs the floor and then recovers the soiled solution all in one pass. The Vision 17E can be adapted to clean any hard floor surface with a variety of floor cleaning accessories including a variety of bassine, steel, polypropylene, and nylon scrub brushes, pads and pad drivers. See the list of optional accessories on page 16 of this manual.
120 VOLT, 50/60 CYCLE MACHINES GROUNDING INSTRUCTIONS This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
PROCEDURES FOR TRANSPORTING How to Put the Machine Into a Van or Truck WARNING: This machine is heavy. Get assistance before attempting to transport or move. Use two able persons to move the machine or a ramp or incline. Always move slowly. Do not turn the machine on a ramp. Do not stop and leave the machine on a ramp or incline. To load the machine into a van or truck follow this procedure: 1. Remove the squeegee and the brush (see "How to Prepare Machine for Operation"). 2.
MACHINE CONTROLS and FEATURES Brush Switch. See Figure 2. Brush Vacuum Solution The brush switch is to the left of the vacuum switch on the control panel. To start the brush motor, press the top of the switch. To stop the brush motor, press the bottom of the switch. Figure #2 Vacuum Switch. See Figure 3. The vacuum switch is to the left of the solution control knob. To start the vacuum motor, press the top of the switch. To stop the vacuum motor, press the bottom of the switch. Solution Control Knob.
MACHINE CONTROLS and FEATURES (cont'd) Brush Control Pedal. See Figure 5. The brush control pedal is at the back of the machine in the lower right corner. Use your foot to operate the pedal. To lower the brush, push the pedal down and to the left, releasing it from the locked position. To raise the brush, push the pedal down and to the right engaging the lock. Figure #5 Brush Tilt Control. The brush tilt control is on the left side by the motor.
MACHINE CONTROLS and FEATURES (cont'd) a Machine Control Handle. See Figure 8. The machine control handle (a) is located on the back side of the machine. The handle is adjustable for operator comfort and ease. The handle adjustment knobs are located at the base (b) of the handle. b Figure #8 Machine Lift Handle. See Figure 9. The machine lift handle is located on the front of the machine. Use this handle to lift the machine when changing the brush.
HOW TO PREPARE THE MACHINE FOR OPERATION How to Install the Squeegee Connection TUBE The proper method for assembling the squeegee connection is as follows:: NUT GASKET 1. Unscrew the nut completely. ELBOW 2. Slide the nut and gasket onto the tube. (Figure 1a) 3. Slide the elbow onto the tube and make sure the gasket is secured into the elbow. (Figure 2a) Figure 1a 4. As you hold the elbow tight onto the tube, tighten the nut over the gasket and the elbow.
HOW TO PREPARE THE MACHINE FOR OPERATION (cont'd) 6. To install the brush or pad driver, align the lugs on the locking plate of the pad driver or brush with the adapter plate. 7. Turn the brush or pad driver clockwise to lock it into position. 8. To remove a brush or pad driver, turn the pad driver or brush to the left and remove. 9. Lift up the machine with the lift handle and return the support leg to its normal position.
HOW TO OPERATE THE MACHINE Filling the Solution Tank To fill the solution tank, follow this procedure: 1. Lift the solution tank lid out of the opening. Allow the lid to hang to the front of the machine. See figure # 14. 2. With a hose or bucket fill the solution tank with clean water to within one inch of the bottom of the opening. Figure #14 3. Add a cleaning chemical to the water. For the correct amount, follow the manufacturer's directions shown on the chemical container. 4.
HOW TO OPERATE THE MACHINE (cont'd) 8. To turn the machine, push the rear of the machine to the side opposite the direction you want to turn. It is NOT RECOMMENDED that you move the machine backward during a cleaning operation. 9. When you make more passes across the floor, let the brush clean approximately 2 inches of the area already cleaned by the last pass. NOTE: During most cleaning procedures, apply and remove the solution in one operation.
MAINTENANCE DANGER: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be done by authorized Clarke personnel only. DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before operation. Keep all fasteners tight.
MAINTENANCE (cont'd) 6. Make sure the bumper skirt is in position. The bumper skirt prevents solution from flowing from under the frame. 7. Make sure the brush is in position. 8. Make sure the vacuum hose is installed and on the squeegee. See Figure #19. 9. Connect the power cord to the electrical outlet. Figure #18 Procedures to be Performed at the End of Work 1. Disconnect form power. 2. Drain and flush the tanks. To drain the recovery and solution tanks, follow this procedure: 1.
CLARKE TECHNOLOGY Vision 17E 115V Machine Variables 11/98 Electric - 115V Variable Code 00371A 00372A Breakdown: 00370A 51436B Vision 17E Std. Base Machine 115V Brush, Polypropylene 00370A 53126B Vision 17E Std. Base Machine 115V Pad Driver Breakdown: Accessories: Part No.
NOTES
Vision 17E 115V Section II Parts and Service Manual (78452B)
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM There isn't any solution flow. The solution flow does not stop. The machine does not remove any water from the floor. The machine does not remove all the water from the floor. ACTION CAUSE The solution tank is empty. Fill the solution tank. The solution knob is turned too far to the left. There is an obstruction in the hose or filter. Turn the solution knob to the right. Remove the obstruction from hose or filter.
NOTES CLARKE TECHNOLOGY Operator's Manual - Vision 17E 115V Page -21-
CLARKE TECHNOLOGY Vision17 E 115V Model #00370A 115V Machine Assembly 2/01 2 3 4 50 1 25 21 26 18 27 24 28 23 38 51 22 5 8 39 31 24 44 53 54 45 18 41 35 46 34 43 33 34 40 32 19 29 6 20 41 48 36 42 10 10 10 31 18 11 8 7 9 49 17 37 18 16 12 13 15 14 47 Page -22- CLARKE TECHNOLOGY Operator's Manual -Vision 17E 115V
CLARKE TECHNOLOGY Vision 17 E 115V Models #00370A 115V Machine Assembly Parts List 2/01 Ref 1 2 3 4 5 6 7 8 9 10K 11K 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 40 41K 42 43 44 45 46 47 48K 49 50 51 52 53 54 NI NI NI NI NI NI Part No.
CLARKE TECHNOLOGY Vision 17E 115V ASM, Non Traverse Drawing & Parts List 11/98 Form #10505A 4 3 1 2 5 6 1 3 4 Ref 1 2 3 4 5 6 Part No.
CLARKE TECHNOLOGY Vision 17E 115V Brush Lift Drawing & Parts List 11/98 Form #16608A 2 5 4 5 3 3 4 2 1 Ref 1 2 3 4 5 Part No.
CLARKE TECHNOLOGY Vision 17E 115V ASM, Main Frame Drawing 2/01 Form #16923A 7 39 38 23 7 3 4 5 6 2 1 37 34 12 11 10 25 30 13 15 14 35 29 20 15 33 28 31 18 27 26 15 17 15 36 21 9 24 32 19 5 22 Page -26- 15 CLARKE TECHNOLOGY Operator's Manual -Vision 17E 115V
CLARKE TECHNOLOGY Vision 17E 115V ASM, Main Frame Parts List 2/01 Form #16923A Ref 1 2 3 4 5 6 7K 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37K 38K 39K Part No.
CLARKE TECHNOLOGY Vision 17E 115V Brush Motor Assembly Drawing and Parts List 2/01 Form #17115A 1 2 3 17 4 5 6 16 15 7 9 10 14 8 11 12 13 Ref 1 2 3 4 5 6 7 8 9 Part No. 47710A 44713A 80501A 81104A 980662 67865A 63600A 84242A 20308A Description Terminal, Brush Motor Gear Mtr. 200 RPM 115V Key (with #4) Nut ¼ - 20 Nylock Washer Spacer Tilt handle Guide RH Screw ¼ - 20 X 5/8 Adapter Motor Qty 2 1 1 2 1 1 2 1 Ref 10 11 12 13 14K 15 16 17 Part No.
CLARKE TECHNOLOGY Vision 17E - 115V Panel Assembly Drawing & Parts List 11/98 Form #17644A 1 1 2 12 10 11 4 10 9 8 7 13 3 6 5 5 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13K NI NI Part No.
CLARKE TECHNOLOGY Vision 17E 115V Squeegee Assembly Drawing & Parts List 4/96 Form #18809A 2 4 1 3 8 7 6 1 5 Ref 1 2 3 4 5 6 7 8 Part No. 66921B 30902A 27703A 30903A 85398A 838201 839702 962841 Description Retainer, Squeegee Blade, Squeegee Rear Squeegee, Casting Blade, Squeegee Front Screw ¼ - 20 X ½ Spacer, Wheel Guide Wheel, Brush Guide Screw, 5/16 - 18 x 1¼ Blades Available: 30918A Blade, Sq., Front Nitrile/EPDM 30919A Blade, Sq.
CLARKE TECHNOLOGY Vision 17E 115V Solution Tank Assembly Drawing & Parts List 2/01 Form #19169A 25 26 1 2 10 16 23 3 15 38 39 22 28 29 14 30 40 31 10 17 24 4 5 11 32 33 36 27 10 34 12 13 19 20 21 35 6 7 8 37 18 9 Ref 1 2 3 4 5 6 7 8 9 10 11K 12 13 14 15 16 17 18 19 Part No. 692409 85519A 832322 878535 60317A 53614A 849401 53618A 35138A 962798 49067A 30416A 752020 832002 839401 38964B 962943 722021 833401 Description Chain Cover Screw ¼ - 20 X 3/8 Cover, Sol. Tank Strainer, Sol.
CLARKE TECHNOLOGY Vision 17E 115V Recovery Tank Assembly Drawing & Parts List 2/01 Form #19170A 1 2 5 4 6 7 20 18 8 19 9 10 17 16 11 4 11 13 12 14 15 Ref 1 2 4 5 6 7 8 9K 10K 11 Part No. 58012A 59320A 837304 962798 692409 832322 34256A 56459A 81110A 920797 Description Strainer, Rec. Tank Tube, Stand, Recovery O'Ring Seal Screw, 10-24 x ½ Chain, Cover Cover, Solution Tank Gasket, Rec.
CLARKE TECHNOLOGY Vision 17E 115V 115V Vacuum Motor Drawing & Parts List 11/93 #44906A 2 1 3 4 13 5 6 20 7 9 8 14 15 16 10 21 11 17 12 18 19 Ref # 1 2 3 4 5 6 7 8 9 10 11 Part No.
CLARKE TECHNOLOGY Vision 17 115V ASM, Gear Box #54238A Drawing & Parts List 11/93 9 8 7 6 5 4 3 2 1 Ref 1 2 3 4 5 6 7 8 9 NI Page -34- Part No.
CLARKE TECHNOLOGY Vision 17E 115V Brush Motor 44713A Parts List 8/97 13 7 12 12 1 13 2 SEAM LOCATION 3 14 16 4 15 5 17 6 8 9 10 11 Item 1 2 3 4 5 Part No. 56477A 50141A 902654 902550 51839A 6 7 8 9 10 11 12 13 14 15 16 17 50520A 56480A 962546 50518A 448396 50516A 55654A 55655A 59805A 50515A 80501A 54238A Description Stator Frame Assembly (w/Magnets & Clips) Armature Assembly (w. B.E. & F.E. Bearings) Bearings B.E. Bearing F.E.
CLARKE TECHNOLOGY Vision 17 E 115V Model #00370A - 115V Electrical Schematic 2/01 Page -36- CLARKE TECHNOLOGY Operator's Manual -Vision 17E 115V
CLARKE TECHNOLOGY Vision 17 E 115V Model #00370A - 115V Connection Diagram 2/01 CLARKE TECHNOLOGY Operator's Manual - Vision 17E 115V Page -37-
CLARKE TECHNOLOGY Vision 17E Parking Brake Kit 10773A 6/98 2 1 3 11 10 4 5 2 4 5 6 7 8 9 Ref # 1 2 3 4 5 6 7 8 9 10 11 Part # 66536A 87027A 17519A 87036A 85397A 67422A 87613A 67133A 10735A 608340 Ref. Description Pin, Brake Washer Brake,Pad Weldment Washer, #10 S.S. Screw, 10-24 x3/8 S.S. Shaft, Brake Washer, Nylon Rod, Brake Pedal, Brake Spring, Brake Machine Frame Qty. 2 2 1 2 2 1 2 1 1 1 ref. The brake control prevents the movement of the machine.
ALTO® PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St. Louis, Missouri 16253 Swingley Ridge Road, Suite 200 Chesterfield, Missouri 63017-1725 PRODUCTION FACILITIES ALTO U.S. Inc., Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 ALTO U.S. Inc., Bowling Green, Ohio 43402 1100 Haskins ALTO U.S. Inc., Clearwater, Florida 33765 1500 N.
CLARKE TECHNOLOGY U.S. LIMITED WARRANTY This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations instructions.
E Operator's Manual Vision 17E 230V READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Table of Contents Operator Safety Instructions ................................................................................... Introduction & Machine Specifications .................................................................... Grounding Instructions 230V................................................................................... Procedures for Transporting Machine ..................................................................... Machine Controls & Features .............................
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
Page WARNING: Machines can topple over if guided over the edges of stairs or loading docks and cause injury or damage. Stop and leave this machine only on a level surface. When you stop the machine, put all switches into their "OFF" position. WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized Clarke personnel only.
Introduction & Machine Specifications The newly designed Vision 17 automatic scrubber increases labor efficiency while providing superior cleaning. This unit dispenses the solution, scrubs the floor and then recovers the soiled solution all in one pass. The Vision 17 is available in four models to choose from, two of which are electrical - 115V and 230V. The other two models are battery versions, one a standard battery and the other a battery version with traverse.
Grounding Instructions - 230 Volt 230 VOLT MACHINES INSTRUCTIONS FOR CONNECTION TO THE POWER SUPPLY AND THE ELECTRICAL GROUND CAUTION: To avoid damage to the machine operate only on AC frequency and electrical voltage shown on the nameplate. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. This product must be grounded.
PROCEDURES FOR TRANSPORTING How to Put the Machine Into a Van or Truck WARNING: This machine is heavy. Get assistance before attempting to transport or move. Use two able persons to move the machine or a ramp or incline. Always move slowly. Do not turn the machine on a ramp. Do not stop and leave the machine on a ramp or incline. To load the machine into a van or truck follow this procedure: 1. Remove the squeegee and the brush (see "How to Prepare Machine for Operation"). 2.
MACHINE CONTROLS and FEATURES Brush Switch. See Figure 2. Brush Vacuum Solution The brush switch is to the left of the vacuum switch on the control panel. To start the brush motor, press the top of the switch. To stop the brush motor, press the bottom of the switch. Figure #2 Vacuum Switch. See Figure 3. The vacuum switch is to the left of the solution control knob. To start the vacuum motor, press the top of the switch. To stop the vacuum motor, press the bottom of the switch. Solution Control Knob.
MACHINE CONTROLS and FEATURES (cont'd) Brush Control Pedal. See Figure 5. The brush control pedal is at the back of the machine in the lower right corner. Use your foot to operate the pedal. To lower the brush, push the pedal down and to the left, releasing it from the locked position. To raise the brush, push the pedal down and to the right engaging the lock. Figure #5 Brush Tilt Control. The brush tilt control is on the left side by the motor.
MACHINE CONTROLS and FEATURES (cont'd) Machine Control Handle. See Figure 8 The machine control handle (a) is located on the back side of the machine. The handle is adjustable for operator comfort and ease. The handle adjustment knobs are located at the base (b) of the handle. Figure #8 Machine Lift Handle. See Figure 9. The machine lift handle is located on the front of the machine. Use this handle to lift the machine when changing the brush.
HOW TO PREPARE THE MACHINE FOR OPERATION CAUTION: Leaving the squeegee "DOWN" when the machine is not in use can damage the squeegee blades. Always leave the squeegee in the "UP" position when not in How to Install the Squeegee Connection The proper method for assembling the squeegee connection is as follows:: Figure 1a 1. Unscrew the nut completely. 2. Slide the nut and gasket onto the tube. (Figure 1a) 3. Slide the elbow onto the tube and make sure the gasket is secured into the elbow.
HOW TO PREPARE THE MACHINE FOR OPERATION (cont'd) 6. To install the brush or pad driver, align the lugs on the locking plate of the pad driver or brush with the adapter plate. 7. Turn the brush or pad driver clockwise to lock it into position. 8. To remove a brush or pad driver, turn the pad driver or brush to the left and remove. 9. Lift up the machine with the lift handle and return the support leg to its normal position.
HOW TO OPERATE THE MACHINE Filling the Solution Tank To fill the solution tank, follow this procedure: 1. Lift the solution tank lid out of the opening. Allow the lid to hang to the front of the machine. See figure # 14. 2. With a hose or bucket fill the solution tank with clean water to within one inch of the bottom of the opening. Figure #14 3. Add a cleaning chemical to the water. For the correct amount, follow the manufacturer's directions shown on the chemical container. 4.
HOW TO OPERATE THE MACHINE (cont'd) 8. To turn the machine, push the rear of the machine to the side opposite the direction you want to turn. It is NOT RECOMMENDED that you move the machine backward during a cleaning operation. 9. When you make more passes across the floor, let the brush clean approximately 2 inches of the area already cleaned by the last pass. NOTE: During most cleaning procedures, apply and remove the solution in one operation.
MAINTENANCE DANGER: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be done by authorized Clarke personnel only. DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before operation. Keep all fasteners tight.
MAINTENANCE (cont'd) 6. Make sure the bumper skirt is in position. The bumper skirt prevents solution from flowing from under the frame. 7. Make sure the brush is in position. 8. Make sure the vacuum hose is installed and on the squeegee. See Figure #19. 9. Connect the machine power cord to the electrical outlet. Figure #18 Procedures to be Performed at the End of Work 1. Disconnect machine from power source. 2. Drain and flush the tanks. To drain the recovery and solution tanks, follow this procedure: 1.
CLARKE TECHNOLOGY Vision 17E 203V Machine Variables 11/98 Electric - 115V Electric - 230V Variable Code 00371B 00372B 00370E Breakdown: 00370B 51436B Vision 17E Std Base Machine 230V Brush, Polypropylene 00370B 53126B Vision 17E Std Base Machine 230V Pad Driver 00370E Vision 17E 230V Base with Parking Brake Breakdown: Breakdown: Accessories: Part No.
NOTESS
Vision 17E 230V Section II Parts and Service Manual (78453B)
HOW TOO CORRECT PROBLEMS IN THE MACHINE PROBLEM There isn't any solution flow. The solution flow does not stop. The machine does not remove any water from the floor. The machine does not remove all the water from the floor. CAUSE The solution tank is empty. Fill the solution tank. The solution knob is turned too far to the left. There is an obstruction in the hose or filter. Turn the solution knob to the right. Remove the obstruction from hose or filter. The solution valve or linkage is damaged.
NOTESS CLARKE TECHNOLOGY Operator's Manual - Vision 17E 230V Page -21-
CLARKE TECHNOLOGY Vision17E (230V) Machine Assembly 2/01 2 3 4 1 50 25 57 21 26 18 27 55 28 24 23 38 56 38 39 22 31 24 44 33 34 40 54 18 10 10 36 42 58 31 18 20 48 10 32 6 46 19 41 29 45 41 35 53 34 43 8 7 9 49 17 18 37 16 12 13 15 14 47 Page -22- CLARKE TECHNOLOGY Operator's Manual -Vision 17E 230V
CLARKE TECHNOLOGY Vision 17E 230V Machine Assembly Parts List 2/01 Ref 1 2 3 4 5 6 7 8 9 10K 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 31 32 33 34 35 36 37 38 39 40 41K 42 43 44 45 46 47 48K 49K 50 51 53 54 55 56K 57 58K NI NI NI NI Part No.
CLARKE TECHNOLOGY Vision 17E (230V) ASM, Non Traverse Axle Drawing & Parts List Form #10510A 2/01 4 6 3 1 2 1 1 3 1 5 6 4 Ref 1 2 3 4 5 6K Part No. 87613A 61247A 59936C 54014A 60196A 87039A Description Washer, Nylon 5/8 Bracket, axle Wheel Fitting, Grease, ¼"-20 Shaft Washer, Fender ¼" SS Qty 7* Nominal 1 2 2 1 2 NOTE: Place washers as required to center the wheels (Number of washers may vary) NOTE: Grease wheels once a week.
CLARKE TECHNOLOGY Vision 17E (230V) Brush Lift Drawing & Parts List 11/98 ASM Form #16608A 2 5 4 5 3 3 4 2 1 Ref 1 2 3 4 5 Part No.
CLARKE TECHNOLOGY Vision 17E (230V) ASM, Main Frame Drawing 2/01 Form #16923A 7 42 3 50 49 5 6 7 46 2 88 1 48 12 23 29 37 39 3635 43 29 33 11 25 33 34 15 10 30 29 28 20 31 38 26 44 15 45 27 17 32 5 22 -26- 16 9 24 47 19 15 35 18 21 Page 13 14 40 15 CLARKE TECHNOLOGY Operator's Manual -Vision 17E 230V
CLARKE TECHNOLOGY Vision 17E (230V) ASM, Main Frame Parts List 2/01 Form #16923A Ref 1 2 3 4 5 6 7K 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 42 43 44 45 46 47 48 49K 50K Part No.
CLARKE TECHNOLOGY Vision 17E (230V) Brush Motor Assembly Drawing and Parts List 2/01 Form #17114A 1 2 3 17 4 5 6 16 15 7 9 10 14 8 11 12 13 Ref 1 2 3 4 5 6 7 8 9 Part No. 47604A 44711A 80501A 81104A 980662 67865A 63600A 84242A 20308A Description Terminal, Brush Motor Gear Mtr 250 RPM 230V Key (with #4) Nut 1/4 - 20 Nylock Washer Spacer Tilt handle Guide RH Screw 1/4 - 20 X 5/8 Adapter Motor Qty 2 1 1 2 1 1 2 1 Ref 10 11 12 13 14K 15 16 17 Part No.
CLARKE TECHNOLOGY Vision17E (230V) Panel Assembly Drawing & Parts List 2/01 Form # 17647A 1 1 2 9 13 12 10 11 3 4 10 15 9 14 8 7 16 3 6 5 5 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16K NI NI NI NI NI NI Part No.
CLARKE TECHNOLOGY Vision 17E (230V) Squeegee Assembly Drawing & Parts List 11/98 Form 18809A 2 4 1 3 8 7 6 1 5 Ref 1 2 3 4 5 6 7 8 Part No. 66921B 30902A 27703A 30903A 85398A 838201 839702 962841 Description Retainer, Squeegee Blade, Squeegee Rear Squeegee, Casting Blade, Squeegee Front Screw ¼ - 20 X ½ Spacer, Wheel Guide Wheel, Brush Guide Screw, 5/16 - 18 x 1¼ Blades Available: 30918A Blade, Sq., Front Nitrile/EPDM 30919A Blade, Sq.
CLARKE TECHNOLOGY Vision 17E (230V) Solution Tank Assembly Drawing & Parts List 2/01 Form #19169A 25 26 1 2 10 16 23 3 15 38 39 22 28 29 14 30 40 31 10 17 24 4 5 41 32 33 36 27 10 34 12 13 19 20 21 35 6 7 8 37 18 9 Ref 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 Part No. 692409 85519A 832322 878535 60317A 53614A 849401 53618A 35138A 962798 30416A 752020 832002 839401 38964B 962943 722021 833401 Description Chain Cover Screw ¼ - 20 X 3/8 Cover, Sol. Tank Strainer, Sol.
CLARKE TECHNOLOGY Vision 17E (230V) Recovery Tank Assembly Drawing & Parts List 2/01 Form #19170A 1 2 5 4 6 7 20 18 8 19 21 10 17 16 11 4 11 13 12 14 15 Ref 1 2 Part No. 58012A 59314A Description Strainer, Rec. Tank Tube, Stand, Recovery 4 5 6 7 8 10K 11 12 837304 962798 692409 832322 34256A 81110A 920797 66933A O'Ring Seal Screw, 10-24 x ½ Chain, Cover Cover, Solution Tank Gasket, Rec.
CLARKE TECHNOLOGY Vision 17E (230V) Vacuum Motor Drawing & Parts List 11/93 Form #44907A 2 1 3 4 13 5 6 20 7 9 8 14 15 16 10 21 11 17 12 18 19 Ref # 1 2 3 4 5 6 7 8 9 10 11 Part No.
CLARKE TECHNOLOGY Vision 17E (230V) ASM, Gear Box #54238A Drawing & Parts List 11/93 9 8 7 6 5 4 3 2 1 Ref 1 2 3 4 5 6 7 8 9 NI Page -34- Part No.
CLARKE TECHNOLOGY Vision 17E (230V) Brush Motor 44711A Parts List 8/97 13 7 12 12 1 13 2 SEAM LOCATION 3 14 16 4 15 5 17 6 8 9 10 11 Item 1 2 3 4 5 Part No. 56477A 50140A 902654 902550 51837A 6 7 8 9 10 11 12 13 14 15 16 17 50520A 56480A 962546 50519A 448396 40819A 55654A 55655A 59805A 50515A 80501A 54238A Description Stator Frame Assembly (w/Magnets & Clips) Armature Assembly (w. B.E. & F.E. Bearings) Bearings B.E. Bearing F.E.
CLARKE TECHNOLOGY Vision 17E (230V) Model #00370B - 230V Electrical Schematic 2/01 Page -36- CLARKE TECHNOLOGY Operator's Manual -Vision 17E 230V
CLARKE TECHNOLOGY Vision 17E Model #00370B - 230V Connection Diagram 2/01 CLARKE TECHNOLOGY Operator's Manual - Vision 17E 230V Page -37-
CLARKE TECHNOLOGY Vision 17E (230V Europe) Model #00370E - Electrical Schematic 2/01 Page -38- CLARKE TECHNOLOGY Operator's Manual -Vision 17E 230V
CLARKE TECHNOLOGY Vision 17E (230V Europe) Model #00370E - Connection Diagram 2/01 CLARKE TECHNOLOGY Operator's Manual - Vision 17E 230V Page -39-
NOTES
ALTO® PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St. Louis, Missouri 16253 Swingley Ridge Road, Suite 200 Chesterfield, Missouri 63017-1725 PRODUCTION FACILITIES ALTO U.S. Inc., Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 ALTO U.S. Inc., Bowling Green, Ohio 43402 1100 Haskins ALTO U.S. Inc., Clearwater, Florida 33765 1500 N.
CLARKE TECHNOLOGY U.S. LIMITED WARRANTY This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations instructions.
