Division of ENCORE S28/L28 S33/L33 S38/L38 Operator's Manual U.S. Patent No. 6,105,192; No. 5,383,251; No. 6,493,896 (Deluxe Machines) and other Patents Pending READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
Table of Contents Operator Safety Instructions ............................................................................................................................. 3 Introduction & Machine Specifications "L" Class ............................................................................................. 5 Introduction & Machine Specifications "S" Class ............................................................................................ 6 Procedures For Transporting ......................
OPERATOR SAFETY INSTRUCTIONS WARNING Clarke® AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
Page WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized Clarke personnel only. WARNING: Any alterations or modifications of this machine could result in damage to the machine or injury to the operator or other bystanders. Alterations or modifications not authorized by the manufacturer voids any and all warranties and liabilities.
Introduction & Machine Specifications Introduction & Machine Specifications Clarke’s newly designed Encore 38, 33 and 28 automatic scrubbers are efficient and superior floor cleaning machines. The Encore 38 uses two brushes or pads to scrub a path 38 inches wide. The Encore 33 uses two brushes or pads to scrub a path 33 inches wide. The Encore 28 uses two brushes or pads to scrub a path 28 inches wide.
Introduction & Machine Specifications (Con't) SPECIFICATIONS: Model S38 - 00680A S33 - 00660A S28 - 00640A Motor, Vac 1 HP (67kw) three stage tangential discharge 36 volt (6-6V batteries) 250AH, 330AH, or 370AH 30 gallon (114 liter) 30 gallon (114 liter) 1 hp PM (.74kw) .50 hp PM (.37kw) 19 inch (48cm) w/.5" (1.5cm) overlap 200 rpm 150 lbs. Variable to 230 ft./min. Variable to 180 ft./min. 36V, 25A, 115V/60hz 66 inches (168cm) 28 inches (71cm) 44 inches (112cm) 42,000 sq ft/hr (3,901 sq. m/hr) 37.
PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: The machine is heavy. Make sure you use two able persons to assist the machine in climbing the ramp. 1. Make sure the loading ramp is at least eight (8) feet long, and strong enough to support the machine. 2. Make sure the ramp is clean and dry. 3. Put the ramp in position. 4. Remove squeegee assembly, brush housings, & brushes or pad drivers before loading. 5. Turn key switch "ON". 6.
SYMBOLS USED ON ENCORE S38, S33, & S28 and L38, L33, & L28 Warning ("L Class" & "S Class') Power ("L Class" & "S Class") On/Off Key Switch ("L Class" & "S Class") Traverse Speed Control ("L Class" & "S Class") Solution Control ("L Class" & "S Class") Brush Up/Down ("L Class" & "S Class") Page -8- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
SYMBOLS USED ON ENCORE S38, S33 & S28 L38, L33, & L28 Squeegee/Vacuum ("L Class" Only) Battery Meter ("L Class" & "S Class") Hour Meter ("L Class" & "S Class") Brush Pressure Increase/Decrease ("L Class" Only) Warning Label ("L Class" & "S Class") with parking brake Brush Pressure Meter ("L Class" Only) Warning Label ("L Class" & "S Class") without parking brake Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 -9-
MACHINE CONTROL PANEL (S38, S33 & S28) Key Switch (See Figure #1, Item "A") The key switch turns "ON" the power to the control panel. "0" is "OFF" and "1" is "on". Traverse Speed Switch (See Figure #1, Item "B") The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left.
MACHINE CONTROL PANEL (L38, L33 & L28) Key Switch (See Figure #2, Item "A") The key switch turns "ON" the power to the control panel. "0" is "OFF" and "1" is "on". Traverse Speed Control Knob (See Figure #2, Item "B") The speed control varies from low to high speed. To increase the speed, turn the knob to the right. To decrease the speed, turn the knob to the left.
MACHINE CONTROL PANEL (L38, L33 & L28) Circuit Breakers (See Figure #2, Item "K"-"P") The circuit breaker reset buttons are located on the rear cover, below the control handle. The breakers are located as follows: Item K & L - Brush Motors (35A) Item M - Traverse Motor (30A) Item N - Vac Motor (25A) Item O - Actuator Motor, Brush Head (5A) Item P - Actuator Motor, Squeegee (1.5 Amp) If a circuit breaker trips, determine which motor is not operating and turn the key switch "OFF".
MACHINE CONTROLS & FEATURES Squeegee Lift Handle See Figure #5a, 5b, & 5c. The squeegee lift handle is located below the control handles on the right side. It is used to raise or lower the squeegee. The vac motor is turned on when the handle is lowered. (S38, S33 & S28 models only). Parking Brake (Optional)See Figure #6. The parking brake prevents movement of the machine. The brake is located on the left hand side of the transaxle motor.
HOW TO PREPARE THE MACHINE FOR OPERATION 38720B The 38, 33 and 28 Encore machines use six 6-volt or three 12-volt batteries. The batteries are located in the battery compartment under the recovery tank. 38720B 38722B How To Install The Batteries To Install the batteries, follow this procedure: 1. Turn key switch off. 38722B 2. Make sure both tanks are empty. 3. Disconnect the hoses from the recovery tank (upper tank) & unplug the vac motor. Remove the recovery tank. 38720B 38722B Figure #8a 4.
HOW TO PREPARE THE MACHINE FOR OPERATION 6. Join the connector from the battery pack to the connector on the control panel. See figure #9. 7. Install the tank, reconnecting hoses and replace the two screws attaching the solution tank to the rear of the frame. NOTE: Charge the batteries before using the machine. Battery Maintenance Figure #9 The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventive maintenance.
HOW TO PREPARE THE MACHINE FOR OPERATION How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion. To prevent an explosion, charge the batteries only in an area with good ventilation. WARNING: Lead acid batteries generate gases which could explode. Keep sparks and flames away from batteries.
HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers To install the brushes or pad drivers on the machine, follow this procedure: 1. Turn the key switch "ON". 2. Put the brush switch in the "UP" position. 3. Turn the key switch "OFF". 4. Go to the front of the machine. 5. Unlatch right and left brush housings and remove them. See figure #13. Figure #13 6. Put a brush or pad driver under the brush motor plate. See figure #14. 7.
HOW TO OPERATE THE MACHINE How To Operate the Squeegee ("S Class" models only) The squeegee wipes the floor while the vacuum motor removes the dirty solution from the floor. Use your right hand to lower or raise the squeegee handle. To operate the squeegee, follow this procedure: 1. To lower the squeegee and start the vac motor move the squeegee lever to the right and down. See figure #15. 2. To raise the squeegee, lift the squeegee lever up. See figure #16.
HOW TO OPERATE THE MACHINE (cont.) NOTE: Put the machine in the slow traverse speed. Use the machine in an area that has no furniture and objects until you can do the following: 1. Move the machine in a straight direction, forward and backward. 2. Stop the machine safely. 3. Move the machine in a straight direction after you turn the machine. To move the machine, follow this procedure: 1. Turn the key switch “ON” position. Figure # 19 2. Put the brush switch in the "UP" position. 3. Raise the squeegee.
HOW TO OPERATE THE MACHINE (cont.) HOW TO CLEAN A FLOOR WARNING: Water solutions or cleaning materials used with this type of machine can leave wet areas on the floor surfaces. These areas can cause a dangerous condition for the operator or other persons. Always put CAUTION signs near the area you are cleaning. 3 To clean a floor, follow this procedure: 1. Put the water and a cleaning chemical in the clean solution tank. 2. Turn the key switch "ON". 4 3. Lower the squeegee. 4.
MAINTENANCE WARNING: Maintenance and repairs must be done by authorized personnel only. WARNING: Always empty the solution tank and recovery tank before doing any maintenance. WARNING: Keep all fasteners tight. These Maintenance Procedures Must Be Done Every Day Keep the machine clean, it will need fewer repairs and have longer life. Figure #22 Do These Procedures When You Begin Your Work Period 1. Turn off key switch. 2. Disconnect the plug on the charger from the connector on the back of the machine.
MAINTENANCE Do These Procedures When You End Your Work 1. Drain the solution tank (Figure #25a) and the recovery tank (Figure #25b). To drain the tanks , follow this procedure: 2. Drain the solution tank (Figure #25a) and the recovery tank (Figure #25b). To drain the tanks , follow this procedure: 25 a. Turn the key switch “OFF”. Figure #25a b. Remove the drain hose from the back of the machine. c. Put the end of the hose over a drain or bucket. d. Turn the valve handle to the left.
MAINTENANCE These Maintenance Procedures Must Be Done Every Week: WARNING: Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and the recovery tank before doing any maintenance. Keep all fasteners tight. WARNING: Always wear eye protection and protective clothing when working near batteries. Do not put tools or other metal objects across the battery terminals or the tops of the batteries.
MAINTENANCE 7. Check the squeegee and the scrub brushes or the pad drivers for damage. 8. Check the squeegee and the vacuum hose for dam age, leaks and obstructions. Maintenance For The Squeegee To remove the squeegee, follow this procedure: 1. Remove the squeegee assembly by loosening the two knobs that attach the squeegee to the machine. Pull the squeegee assembly off. See figure #28. Figure #28 2. Inspect the squeegee blade. 3.
MAINTENANCE Adjusting Squeegee Blades When properly installed the front blade should be approximately .06 above the rear blade. See figure #31. Adjusting Squeegee Support Wheels: .12 The support wheels should be set at .12 above the floor with the rear blade touching the floor. See figure #31. WARNING: Maintenance and repairs must be done by authorized personnel only . WARNING: Figure #31 Electrical repairs must be done by authorized personnel only.
Clarke® Encore 28/33/38 Accessories - 6/02 ACCESSORIES Description Power Wand System Kit ESP Recycle System Kit Soft Caster Asm. Clarke Care Kit Squeegee Asm.
Division of Encore S28/L28/S33/L33/S38/L38 Section II Parts and Service Manual (70656A) U.S. Patent No. 6,105,192; No. 5,383,251; No.
HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM The machine does not remove all the water from the floor. The batteries do not give the normal running time. The cleaning is not even. CAUSE ACTION The squeegee is up Lower the squeegee. The vacuum tank is full. Drain the tank. The screen filter is dirty. Clean the screen filter. There is an obstruction or damage in the squeegee, squeegee hose or standpipe. Remove the obstruction or repair the damage. The vacuum motor is not running.
MAINTENANCE Adjusting Brush Head Position Switch: (See figure 34) 1.Turn "ON" the key switch. 2. Start with the brush head up/down switch in the "Up" position and the brush pressure knob set to minimum, fully counter clockwise. This should cause the brush head to be in the full "Up" position. 3. Install the proper brushes or pads and pad drivers for the machine. 4. Leave the brush pressure knob set to minimum, fully counter clockwise. Switch the brush head up/down switch to the "Down" position.
Clarke® Encore S28/S33/S38 and L28/L33/L38 Squeegee/Swing Arm Assembly Drawing 5/04 Drawing # 16616A - L Drawing # 16617A - S 55 53 2 1 7 2 6 53 3 50 8 53 57 4 9 10 16 6 15 23 16 53 11 25 12 13 24 26 52 51 14 58 5 18 6 19 20 22 27 21 10 NOTE: #51 and #52 are on top of the bracket for the "S" models 29 6 28 31 32 48 30 33 56 37 17 32 28 34 47 41 42 35 43 40 38 39* 37 36 54 44 45 46 49 * Apply antiseize to threads Page -30- Clarke® Operator's Manual -Encore S2
Clarke® Encore S28/S33/S38 and L28/L33/L38 Squeegee/Swing Arm Assembly Parts List 5/04 Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Part No. 57275A 87623A 60452A 86004A 85730A 81104A 38021A 61679A 51613A 920110 60332A 920256 81105A 920296 962798 87624A 80015A 53423A 68016A 170915 64905A 980651 60678C 25201A 35192A 61267A 34260B 81301A 59971A 65975A 920248 980645 59950A 980638 Description Pulley Washer, Nylon 1¼x¼x1/8 Swing Arm, Front Screw, .
Clarke® Encore S28/S33/S38 and L28/L33/L38 Traverse System Assembly Drawing 8/03 Drawing 19021A 18 24 25 26 27 16 8 23 10 7 9 6 5 15 7 23 19 28 4 19 14 3 20 3 29 1 30 11 2 21 22 30 13 32 31 13 12 Page -32- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 and L28/L33/L38 Traverse System Assembly Parts List 8/03 Drawing 19021A Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. 66531A 836711 81104A 69877A 85811A 57275A 87623A 86004A 85703A 85700A 920110 899769 81105A 59116A 15 16 85730A 59969A 59955A 81221A 980614 60230A 65963A 69712A 87625A 80011A 81207A 170883 58419A 980205 69639A 980645 962244 980638 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description Swing Arm Pin Hair Pin Nut, .25-20 ESNA Swing Bracket Screw, .312-18 x .
Clarke® Encore S28/S33/S38 and L28/L33/L38 Brush Head Assembly Drawing 6/02 Drawing # (i) 11453A, 11449A, 11452A Drawing # (ix) 11448A, 11445A, 11450A 2 3 1 4 5 73 36 7 6 13 16 17 8 14 15 12 18 12 11 10 20 18 9 30 28 29 6 27 9 7 26 24 24 1 21 22 25 3 23 32 31 68 33 69 70 67 34 68 35 71 49 37 38 39 38 27 66 18 35 65 40 41 61 64 63 49 48 62 59 45 51 50 4 60 52 58 53 45 54 42 47 46 55 -34- 44 43 27 56 Page 72 57 Clarke® Operator's Manual -Encor
Clarke® Encore S28/S33/S38 and L28/L33/L38 Brush Head Assembly Parts List 8/04 Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Part No. 82501A 60230A 766780 962244 69883A 980608 920056 81105A 920110 65972A 47374A 962980 38708A 42401A 50208A 50209A 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 69188A 85744A 87007A Description Pin Main Frame Hair Pin Screw, .375-16x.75 Switch Bracket Washer, #6 Nut, #6-32 ESNA Nut, .375-16 ESNA Nut, .312-18 ESNA Switch Mount Lever, Switch Screw, #6-32x1.
Clarke® Encore S28/S33/S38 and L28/L33/L38 Solution/Recovery System Assembly Drawing 6/02 1 66 29 2 28 5 3 6 7 4 76 32 8 9 26 10 11 7 22 20 25 24 29 24 23 27 18 13 21 68 45 21 69 46 15 33 28 76 32 34 31 73 74 35 16 17 30 77 75 37 36 12 47 32 78 79 49 48 51 50 52 38 39 53 40 41 42 24 44 43 44 64 -36- 71 72 65 61 44 60 44 63 62 Page 67 60 Clarke® 70 28 54 55 56 57 58 59 Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 and L28/L33/L38 Solution/Recovery System Assembly Parts List 8/04 Ref # 1 2 3 4 Part No.
Clarke® Encore S28/S33/S38 and L28/L33/L38 12/03 Brush Motor #45033A (S33, L28, S28) Brush Motor #45036A (L38, L33, S38) 13 7 12 12 1 13 2 Seam Location 3 14 16 Rotation 4 5 15 6 17 8 9 10 Ref # 1 3 4 5 56478A 46734A 40312A 40318A 902654 902550 51840A 6 7 8 9 10 11 12 13 14 15 16 17 50520A 56480A 962546 50517A 448396 40826A 55657A 55656A 59805A 50515A 80501A 54238A 2 Page -38- Part No.
Clarke® Encore S28/S33/S38 and L28/L33/L38 Gear Box #54238A 6/02 9 8 7 6 5 4 3 2 1 Ref # 1 2 3 4 5 6 7 8 9 NI Clarke® Part No. 57846A 507641 52050A 56668A 51176A 58316A 902605 54883A 58144A Description Ring, Snap Seal, Oil, Small Cap End O'Ring Bearing, Large Shaft & Gear, Gearbox Bearing, Small Housing Seal, Oil Large Darina Grease Operator's Manual - Encore S28/L28/S33/L33/S38/L38 Qty 1 1 1 1 1 1 1 1 1 4oz.
Clarke® Encore S28/S33/S38 and L28/L33/L38 Vac Motor Assembly #45019A 6/02 13 18 2 1 14 4 3 6 15 5 16 7 8 14 9 15 19 14 10 11 17 12 Ref # 1 2 3 4 5 6 7 8 9 10 Page Part No. 51913A 54809A 53905A 85303A 40830A 51914A 50618A 53100A 902679 902648 -40- Description Clip (optional) Housing Fan Screw - 8-32 x 3/8 Carbon Brushes Clamp Bracket Disc Bearing - Ball Bearing - ball, radial Qty 2 1 1 4 2 2 1 1 1 1 Ref # 11 12 13 14 15 16 17 18 19 Clarke® Part No.
Clarke® Part No. 53384A 53385A 80121A 80122A 3 Operator's Manual - Encore S28/L28/S33/L33/S38/L38 2 4 17 5 6 Parking Brake Spare Parts Description Pad, Friction Hub, Shaft Key, 4 MM - Hub Set Screw, M3 - Hub 1 7 8 To replace coupler remove these two screws (Black) to seperate the motor from gearbox to allow access to coupler 9 Qty 1 1 1 1 10 4 16:1 Ratio 36 VDC 15 Cont Volt AMP. Duty Date 11 Ser. No. Mount Shaft 4BC-2800 1200 Ins. Cl. Model RPM .
Clarke® Encore S28/S33/S38 and L28/L33/L38 36 Volt Battery Charger 6/02 WARNING: All electrical repairs must be performed by qualified personnel only. PARTS LIST FOR BATTERY CHARGERS 40506A - 36 Volt D.C., 25A, 115 Volt A.C., 60 Hz 40505A - 36 Volt D.C., 25A, 230 Volt A.C., 50 Hz 40507A - 36 Volt D.C., 25A, 230 Volt A.C., 60 Hz 40514A - 36 Volt D.C., 36A, 115 Volt A.C., 60 Hz 40515A - 36 Volt D.C., 36A, 230 Volt A.C.
SEE PAGES 44 - 51 FOR COMPONENTS FOR MACHINES WITH A 41135C TRAVERSE CONTROLLER Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 - 43 -
Clarke® Encore S28/S33/S38 and L28/L33/L38 Control Housing Assembly Drawing 12/03 Drawing# 13712A (IX) and 13713A (I) (for machines wtih a 41135C Traverse Controller) 1 1 2 3 1 23 1 2 4 5 16 47 59 57 6 9 58 50 50 7 10 7 12 60 8 44 55 11 9 10 11 44 45 60 8 48 49 17 51 45 15 13 21 45 44 19 30 32 35 20 26 25 24 28 56 52 45 14 45 15 18 36 37 54 44 46 14 31 33 34 53 22 27 43 29 42 40 38 Page 39 -44- 41 Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 and L28/L33/L38 Control Housing Assembly Parts List 12/03 (for machines wtih a 41135C Traverse Controller) Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18A 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38* 39 40 41 42 43 44 *#38 must use red loctite set screws. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Clarke® Part No.
Clarke® Encore S28/S33/S38 and L28/L33/L38 Rear Cover Assembly Drawing 6/02 Drawing 13712A & 13713A (for machines wtih a 41135C Traverse Controller) 49 48 3 3 2 48 60 49 4 1 6 7 5 8 10 9 59 11 5 25 8 24 26 12 5 23 13 22 10 12 27 14 17 21 15 18 5 20 19 43 44 29 16 53 22 30 2 31 28 43 42 53 5 41 61 32 47 56 55 33 62 34 54 57 63 40 35 39 47 50 45 44 43 46 58 38 64 36 37 57 52 5 51 58 Page -46- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 and L28/L33/L38 Rear Cover Assembly Parts List 6/02 (for machines wtih a 41135C Traverse Controller) *#23 must use red loctite. Ref # Part No.
Clarke® Encore S28/S33/S38 Electrical Schematic 6/02 (for machines wtih a 41135C Traverse Controller) Page -48- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 Connection Diagram 6/02 (for machines wtih a 41135C Traverse Controller) Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 - 49 -
Clarke® Encore L28/L33/L38 Electrical Schematic 6/02 (for machines wtih a 41135C Traverse Controller) Page -50- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore L28/L33/L38 Connection Diagram 6/02 (for machines wtih a 41135C Traverse Controller) Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 - 51 -
NOTES Page -52- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
SEE PAGES 54-61 FOR COMPONENTS FOR MACHINES WITH A 40089A TRAVERSE CONTROLLER Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 - 53 -
Clarke® Encore S28/S33/S38 and L28/L33/L38 Control Housing Assembly Drawing 12/03 (for machines wtih a 40089A Traverse Controller) 1 1 2 3 1 23 1 2 4 5 16 47 57 6 58 9 34 50 50 10 7 59 44 55 11 8 31 7 12 9 10 11 44 45 59 8 48 49 17 46 51 45 14 15 13 21 45 44 19 30 52 45 37 54 14 20 26 25 24 28 56 36 45 15 18 32 35 33 44 53 22 27 43 29 42 40 38 Page 39 -54- 41 Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 and L28/L33/L38 Control Housing Assembly Parts List (for machines wtih a 40089A Traverse Controller) 12/03 Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18A 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38* 39 40 41 42 43 44 *#38 must use red 45 loctite set screws. 46 47 48 49 50 51 52 53 54 55 56 57 58 59 NI Clarke® Part No.
Clarke® Encore S28/S33/S38 and L28/L33/L38 Rear Cover Assembly Drawing 10/02 (for machines wtih a 40089A Traverse Controller) 49 48 3 3 2 48 60 49 4 1 6 7 5 8 10 9 59 11 5 25 8 24 12 5 23 13 22 10 12 26 14 17 21 15 18 5 20 19 29 43 44 27 22 16 53 66 30 2 31 28 43 53 41 65 5 42 32 47 56 55 67 68 61 33 62 34 54 57 63 40 35 39 47 50 45 44 43 46 58 38 64 36 37 57 52 5 51 58 Page -56- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 and L28/L33/L38 Rear Cover Assembly Parts List 10/02 (for machines wtih a 40089A Traverse Controller) *#23 must use red loctite. Ref # Part No.
Clarke® Encore S28/S33/S38 Electrical Schematic 4/03 (for machines wtih a 40089A Traverse Controller) Page -58- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore S28/S33/S38 Connection Diagram 10/02 (for machines wtih a 40089A Traverse Controller) Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 - 59 -
Clarke® Encore L28/L33/L38 Electrical Schematic 8/04 (for machines wtih a 40089A Traverse Controller) Page -60- Clarke® Operator's Manual -Encore S28/L28/S33/L33/S38/L38
Clarke® Encore L28/L33/L38 Connection Diagram 4/03 (for machines wtih a 40089A Traverse Controller) Clarke® Operator's Manual - Encore S28/L28/S33/L33/S38/L38 - 61 -
NOTES
CLARKE PRODUCT SUPPORT BRANCHES U. S. A.
Clarke® U.S. LIMITED WARRANTY This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations instructions.
