E Division of Image Mini Spot Operator's Manual READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
MACHINE DATA LOG/OVERVIEW MODEL _______________________________________ DATE OF PURCHASE ___________________________ SERIAL NUMBER _______________________________ SALES REPRESENTATIVE # _____________________ DEALER NAME _________________________________ OPERATIONS GUIDE NUMBER ___________________ PUBLISHED ___________________________________ YOUR DEALER Name: _________________________________________________________________________ Address: _________________________________________________________________
Table of Contents Machine Data Log/Overview .............................................................................................. 2 Table of Contents ............................................................................................................... 3 HOW TO USE THIS MANUAL How to use this manual ...................................................................................................... 1-1 SAFETY Important Safety Instructions ...............................................
THIS PAGE LEFT BLANK INTENTIONALLY Page -4- Clarke® Operator's Manual -Image Mini Spot
HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for odering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE WARNING: To reduce the risk of fire, electric shock or injury: Use only indoors. Do not use outdoors or expose to rain. Use only as described in this manual. Use only manufacturer's recommended components and attachments.
HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their despriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words- WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING: WARNING - Hazard or unsafe practices which COULD result in severe personal injury or death.
GROUNDING INSTRUCTIONS THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. Grounding Pin GROUNDING CONNECTION USING AN ADAPTOR Grounding Outlet Metal Screw Fig.
MACHINE OPERATIONS SET UP AND OPERATION 1. 2. 3. 4. 5. 6. 7. 8. 9. Upon removing your new mini-extractor from the box, loosen the latch, at the back end and of the machine, that secures the recovery tank to the solution tank. Remove the recovery tank from the solution tank. Pour clean, hot water to the indicated fill line of the solution tank. To avoid possible tank distortion, water temperature must not exceed 140 F (60C).
MAINTENANCE DAILY MAINTENANCE: Follow same procedure for Shut Down and Storage: Vac Motor Carbon Brushes Replacement PERIODIC MAINTENANCE: 1. Twice a month, flush a white vineger solution (one quart vinegar to two gallons water) or anitbrowning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. 2. If spray jet becomes clogged, remove the spray tip, wash it thoroughly, and blow dry. NOTE: DO NOT USE PINS, WIRE, ETC.
TROUBLESHOOTING/WIRING DIAGRAM TROUBLESHOOTING PROBLEM Little or no solution flow Loss of vacuum/Solution recovery CAUSE SOLUTION Clogged spray jet on cleaning tool Remove and clean jets Faulty pump Check and replace pump. (Call Tech. Service first) Incorrectly attached solution hose Ensure solution hose coupler is securely attached to the coupler on the solution tank. Incorrectly attached vac hose Ensure vac hose is pushed completely onto the recovery tank inlet.
Clarke® Image Mini Spot Recovery Tank Parts 12/02 Parts Inside Portal Cap 10 13 14 1 9 5 2 11 8 3 7 4 6 12 5 Page 5-1 Clarke® Operator's Manual -Image Mini Spot
Clarke® Image Mini Spot Recovery Tank Parts List 12/02 Ref. Part No. Description Qty 1 52875A Asm. Acess Cover 1 2 3 52876A 52877A Screw, 8 x 3/4 PFHT/S BLK ZINC Float Asm. Spotter Weight 6 1 4 5 52878A 52879A Tube Asm. Spotter Screw, 10-32 x 3/8 PPHMS SS NP 1 4 6 7 50356A 52796A Bracket, Rec./Sol. Tank Seal Gasket, Recovery Tank Seal 1 1 8 9 52880A 52881A Tank, Spotter Recovery Plug, Handle Recovery Tank 1 1 10 11 52882A 52883A Plate, Backsplash Shield Latch, Tension 3.
Clarke® Image Mini Spot Solution Tank Parts 12/02 2 24 1 3 4 5 23 22 18 6 28 27 8 16 8 26 9 29 25 10 5 2 11 22 13 14 12 21 18 20 11 15 16 19 17 18 Page 5-3 Clarke® Operator's Manual -Image Mini Spot 7
Clarke® Image Mini Spot Solution Tank Parts List 12/02 Ref. Part No. Description 1 52887A Tank, Spotter Sol.
Clarke® Image Mini Spot Labels and Parts List 12/02 1 6 2 3 4 5 Page 5-5 Ref. Part No.
Clarke® Image Mini Spot Hand Tool and Parts List 12/02 2 11 4 1 3 10 8 5 7 6 9 4 Ref. Part No. Description 1 55179A Housing, Handtool Spotter 1 2 3 52983A 52984A Clamp DHT Valve Hose Asm. Hose/Cuff Connector 1 1 4 5 737141 54177A Nipple, 1/8 FPT QD Fem. Brass Jet, Asm w/o Ring 2 1 6 7 962802 57011A Screw, 8-32 x 1/4 PHST PLTD Plate, Retainer w/Screws 1 1 8 9 56123A 54060A Manifold, Spotter 3/16 Fitting, 1/8 MPT x 3/16 Comp. 1 1 10 11 59618A 737140 Valve Asm.
Clarke® Image Mini Spot Cart and Parts List 12/02 1 2 3 7 8 4 5 6 Page 5-7 Ref. Part No. Description Qty 1 2 61690A 85520A Handle Weldment, Cart Screw, 8-00 x 1/2 Pan Head 1 2 3 4 59951A 920346 Wheel, 8" Palnut 2 2 5 6 50007A 81110A Bumper, Recessed Nut Hex, Elastic Lock, 10-24 1 1 7 8 61689A 962862 Chassis Weldment, Cart Screw, 10-24 x 1/2 PN ST 1 1 Kit 11678A Cart (entire asm.
PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St.
Clarke® WARRANTY This Clarke Industrial Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations instructions. This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear parts such as electrical cable, rubber parts, hoses and motor brushes.
