Operator`s manual

ManualsBrandsClarke ManualsFloor MachineC2K-1800HSV

Form No. 70199A 1/02 CLARKE TECHNOLOGY Printed in the U.S.A.

READ THIS BOOK

CAUTION: Read the Operator's Manual before using the appliance.

This book has important information for the use and safe operation of this machine. Failure to read

this book prior to operating or attempting any service or maintenance procedure to your ALTO

machine could result in injury to you or to other personnel; damage to the machine or to other property

could occur as well. You must have training in the operation of this machine before using it. If your

operator cannot read English, have this manual explained fully before attempting to operate this

machine.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.

C2K Series

230V 50Hz

Polisher

Operator's

Manual

Summary of content (26 pages)

PAGE 1
C2K Series 230V 50Hz Polisher UK Operator's Manual READ THIS BOOK CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
PAGE 2
CONTENTS OF THIS BOOK Operator Safety Instructions ............................................................................................... 3 Machine Introduction .......................................................................................................... 4 Accessories ....................................................................................................................... 5 Machine Specifications ............................................................................
PAGE 3
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner's Manual and on your machine.
PAGE 4
OPERATOR SAFETY INSTRUCTIONS (cont.) WARNING: Use of this machine as a step or furniture could result in injury or damage. Do not use this machine as a step or furniture. Do not ride on this machine. WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this machine. WARNING: Injury to operator or bystanders could occur if an abrupt change in floor surface texture is encountered when using this machine.
PAGE 5
ACCESSORIES The following accessories are available. 1. Polishing and waxing brushes. 2. Brushes with natural or synthetic bristles for scrubbing. 6. Brushes with metal or wood backs and with holes to let the solution flow through. 7. Solution tank. 3. Brushes with steel wire bristles for concrete. 8. Sanding discs for wood floors. 4. Synthetic pad holders. 9. Spray Buff Accessory. 5. Synthetic pads for polishing, scrubbing, stripping and spray buffing. 10. Grinding disk for concrete.
PAGE 6
Machine Specifications Model Code Number Voltage (V) Frequency (Hz) Current (A) Power (kW) Brush Diameter (cm) Block Diameter (cm) Brush Speed (rpm) Cord Length (m) Weight (kg) Noise (dBA) Vibration (m/s2) C2K- 16 01221A 230 50 8 0.56 41 36 204 15 40 <70 <2.5 18 01222A 230 50 8 0.56 46 41 204 15 40 <70 <2.5 160 01223A 230 50 8 0.75 41 41 204 15 40 <70 <2.5 180 01224A 230 50 8 0.75 46 46 204 15 40 <70 <2.
PAGE 7
HOW TO PREPARE THE MACHINE FOR OPERATION WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the pad or brush. How To Install The Brush Or Pad Driver To install the brush or pad driver, follow this procedure: 1. Put the handle in the vertical position. 2. To lock the handle, push the locking lever down.See figure 1. Figure 1 3. Tilt the machine backward until the handle is on the floor. See figure 2. 4. Put one foot on each side of the machine.
PAGE 8
230 VOLT MACHINES Instruction for connection to the power supply and the electrical ground . UK Plug CAUTION: This machine will operate only on the AC frequency and electrical voltage shown on the nameplate. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. This machine must be connected to the electrical ground to protect the operator from electric shock. The machine has a power cord with two main conductors and one earthing conductor.
PAGE 9
HOW TO OPERATE THE MACHINE 1 How To Start/Stop The Machine WARNING: Never start a polisher when the handle is in the vertical position. The following step applies to the C2K-1600DS and C2K2000DS only:Select high or low speed with the switch located on the motor cover. Moving the switch lever up selects high speed. Moving the switch lever down selects low speed.
PAGE 10
NOTES Page -10 - CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
PAGE 11
C2K Series 230V Section II Parts and Service Manual (70199A) CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V Page - 11 -
PAGE 12
MAINTENANCE WARNING: Maintenance must be done by authorized personnel only. CAUTION: Keep all adjustments according to specifications. Maintenance Instructions Return the machine to a Clarke Technology Authorized Service Location every 12 months for maintenance inspections. Switches WARNING: All electrical repairs must be done by authorized personnel only. The machine must be tested after electrical repairs to make sure it is safe to operate.
PAGE 13
NOTES CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V Page - 13 -
PAGE 14
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS Assembly Drawing 2/01 1 2 5 4 3 4 6 3 7 10 1 8 13 31 21 38 1 9 11 10 41 22 43 20 24 19 17 29 23 1 44 16 37 14 26 18 42 30 25 26 22 28 25 15 32 1 23 27 33 24 34 36 Page -14 - CLARKE TECHNOLOGY Operator's Manual - C2K Series
PAGE 15
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-1600, C2K-1800, C2K-2000, C2K-1600HS, C2K-1800HS, C2K-2000HS Assembly Drawing Parts List 2/01 Ref. Part No.
PAGE 16
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Assembly Drawing 2/01 1 2 3 4 5 4 6 7 3 9 10 13 1 41 8 57 10 54 42 38 21 22 43 45 20 16 19 17 44 49 24 23 1 37 14 46 26 50 31 18 51 25 26 47 22 28 15 11 25 12 53 52 1 23 12 30 32 27 11 24 33 1 56 30a 56 55 10 48 34 36 29 10 Page -16 - CLARKE TECHNOLOGY Operator's Manual - C2K Series
PAGE 17
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Assembly Parts List 2/01 Ref. Part No.
PAGE 18
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180 and C2K-200 230V - 50 Hz Motor Assembly Drawing & Parts List 2/01 Note: If your machine has motor #44638A refer to this drawing for service part replacement. 13 1 2 8 3 9 10 11 12 14 15 16 7 4 18 17 6 Ref. Part No. 1 2 3 4 6 7 8 9 58030A 52018A 52019A 54330A 53976A 50400A 56461A 902550 Description Ref. Qty. Screw #10-32 x.
PAGE 19
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180 and C2K-200 Gearbox Assembly Drawing & Parts List 1/02 Note: If your machine has gearbox #50872A refer to this drawing for service part replacement. 2 3 4 5 6 7 8 9 10 11 4 12 4 Ref. Part No. 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 80141A 56922A 902606 58513A 53524A 962794 54858A 902736 58314A 442473 902737 52020A 58312A 902573 Description Screw, Socket Hd.
PAGE 20
CLARKE TECHNOLOGY C2K-1600, C2K-1800, C2K-2000, C2K-1600HS, C2K-1800HS and C2K-2000HS Motor Assembly Drawing & Parts List 1/02 Note: If your machine has motor #50879A or #50880A refer to this drawing for service part replacements. 1 2 3 4 5 "HS" machines Page -20 - 50880A 50879A Ref. Part No. Part No.
PAGE 21
CLARKE TECHNOLOGY C2K-1600, C2K-1800, C2K-2000, C2K-1600HS, C2K-1800HS and C2K-2000HS Gearbox Assembly Drawing & Parts List 1/02 Note: If your machine has gearbox #50881A or #51344A refer to this drawing for service part replacement. 50881A Ref 1 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part No. 80141A 902606 58520A 50852A 962794 54858A 902736 58314A 442473 902737 N/A 58312A 902573 Description Screw, Socket Hd.
PAGE 22
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS 230V Motor Assembly Drawing & Parts List 1/02 Note: If your machine has motor/gearbox #51342A refer to this drawing for service part replacement. 1 1 2 3 15 4 10 14 6 6 5 20 19 6 6 7 16 18 8 9 9 7 9 17 NOTE: indicates a change has been made since the last publication of this manual. Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Part No.
PAGE 23
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Gearbox Assembly Drawing & Parts List 1/02 Note: If your machine has gearbox #51343A refer to this drawing for service parts. 18 17 16 4 11 4 12 10 8 13 13 14 15 9 7 6 5 4 3 1 2 Ref 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Part No. 80141A 56922A 902606 58520A 53539A 962794 54858A 902736 58314A 442473 902737 N/A 58312A 902573 CLARKE TECHNOLOGY Operator's Manual - C2K Series Description Screw, Socket Hd.
PAGE 24
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS Wiring Diagram 230V - 50Hz 3/00 CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Wiring Diagram 230V 3/00 CLARKE TECHNOLOGY C2K-1800HSV Wiring Diagram 230V 2/01 WARNING: All electrical repairs must be performed by qualified personnel only.
PAGE 25
ALTO® PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St. Louis, Missouri 16253 Swingley Ridge Road, Suite 200 Chesterfield, Missouri 63017-1725 PRODUCTION FACILITIES ALTO U.S. Inc., Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 ALTO U.S. Inc., Bowling Green, Ohio 43402 1100 Haskins SERVICE FACILITIES ALTO U.S. Inc.
PAGE 26
CLARKE TECHNOLOGY U.S. LIMITED WARRANTY This ALTO Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of five years from the date of purchase, when operated and maintained in accordance with Clarke Technology's Maintenance and Operations Instructions. This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear parts such as electrical cable, rubber parts and motor brushes.