AIR HAMMER MODEL NO: CAT29B & CAT95 PART NO: 3110408 & 3110851 OPERATING & MAINTENANCE INSTRUCTIONS GC0614
INTRODUCTION Thank you for purchasing this CLARKE Air Hammer. The CAT29B and CAT95 differ only by virtue of the CAT95 having a polished metal casing as opposed to a painted finish. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
GENERAL SAFETY RULES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of the way. 3. Keep children and visitors away - Do not let children handle the tool. USE 1. Stay alert and use common sense - do not operate the tool when you are tired or under the influence of alcohol, drugs or medication. 2.
13. The tool should be serviced at regular intervals by qualified service personnel. 14. Avoid damaging the tool for example by applying excessive force of any kind. 15. ALWAYS maintain the tool with care. Keep it clean for the best and safest performance. 16. Quick change couplings should not be located at the tool. They add weight and could fail due to vibration. 17. DO NOT force or misuse the tool. It will do a better and safer job at the rate for which it was designed. 18. Do not remove any labels.
COMPRESSED AIR REQUIREMENTS WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. • Use only clean, dry, regulated compressed air as a power source. • Air compressors used with the impact wrench must comply with the appropriate European Community Safety Directives. • A build-up of moisture or oil in the air compressor will accelerate wear and corrosion in the impact wrench.
OVERVIEW NO DESCRIPTION 1 Retaining Spring 2 Trigger 3 Regulator 4 1/4” BSP Female Air Inlet NO DESCRIPTION 5 Chisel Set comprising: a Steel Cutter Chisel b Tapered Punch c Straihgt Cold Chisel d Rivet Cutter Chisel e Double-sided Ripping Chisel f Straight Cold Chisel OPERATION NOTE: Ensure the compressed air supply is turned off. 1. If required, connect an in-line mini oiler to the tool. • A mini oiler helps to prolong the life of the air tool.
1. If required, connect an in-line mini oiler to the tool. • A mini oiler helps to prolong the life of the air tool. Read the instructions supplied with the mini-oiler before use. 2. Connect a suitable hose to the tool and the other end of the hose to the compressed air supply. 3. Turn on the air supply and check for air leaks. Rectify any found before proceeding. • PTFE tape may be helpful for sealing threaded connections. • Your air tool is now ready for use. FITTING THE CHISEL 1.
• The retaining spring has a life expectancy, depending upon the intensity of usage. It is recommended that you procure a spare spring for use in the event of failure occurring during the course of a particular job. DISCONNECTING THE AIR SUPPLY Do not disconnect the air supply hose until the air supply has been shut down and the compressed air pressure released. Refer to the compressor instruction manual for the procedure to shut down and release the compressed air.
MAINTENANCE WARNING: MAKE SURE THAT THE TOOL IS DISCONNECTED FROM THE AIR SUPPLY BEFORE STARTING ANY CLEANING, OR MAINTENANCE PROCEDURES. DAILY 1. Before use, drain water from the air tank, air line and compressor. 2. Pour a few drops of CLARKE airline oil, into the air inlet. This should be carried out regardless of whether or not an in-line mini oiler is used. If an inline mini oiler is not used, this procedure should be repeated after every two to three hours of use. 3.
PARTS LIST & DIAGRAM No Description No Description 1 Housing 11 Valve Disc 2 Rubber Gasket 12 Front Valve 3 O-Ring 13 Pin 4 Regulator 14 Pin 5 Control Pin 15 Piston 6 O-Ring 16 Cylinder 7 Ball Valve 17 Retainer Spring 8 Spring 18 Trigger 9 Air Inlet Connector 19 Roll Pin 10 Rear Valve 20 Roll Pin 10 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
DECLARATIONS OF CONFORMITY 11 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
