CBG6250 Bench Grinder.
CBG6250 Bench Grinder.fm Page 2 Thursday, November 10, 2011 3:26 PM INTRODUCTION Thank you for purchasing this CLARKE Bench Grinder. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
CBG6250 Bench Grinder.fm Page 3 Thursday, November 10, 2011 3:26 PM POWER TOOL SAFETY WARNINGS 1) WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY 1.
CBG6250 Bench Grinder.fm Page 4 Thursday, November 10, 2011 3:26 PM 4) POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct accessories for your application. The correct power tool will do the job better and safer at the rate which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3.
CBG6250 Bench Grinder.fm Page 5 Thursday, November 10, 2011 3:26 PM 8. ALWAYS check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the tool's operation. A part that is damaged should be properly repaired or replaced at an authorised service Centre.
CBG6250 Bench Grinder.fm Page 6 Thursday, November 10, 2011 3:26 PM ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
CBG6250 Bench Grinder.fm Page 7 Thursday, November 10, 2011 3:26 PM CARTON CONTENTS The following Items should be supplied in the carton, if any parts are missing or damaged, please contact the clarke dealer where you purchased the bench grinder.
CBG6250 Bench Grinder.fm Page 8 Thursday, November 10, 2011 3:26 PM BEFORE USE MOUNTING THE GRINDER ONTO A WORKBENCH NOTE: We highly recommend that you bolt this bench grinder securely to a workbench to gain maximum stability for your machine. 1. Using the base of the bench grinder as a template, mark the bench through the holes in the casting. 2. Bolt the bench grinder on the bench with bolts, washers and nuts (not supplied). 3. To reduce vibration, mount the bench grinder on a vibration absorbing mat.
CBG6250 Bench Grinder.fm Page 9 Thursday, November 10, 2011 3:26 PM INSTALLING THE EYE SHIELDS 1. Attach the left eye shield arm to the bench grinder using the bracket, flat washer and bolt supplied. 2. Fit the lens to the lens holder as shown. 3. Repeat for right side eye shield. NOTE: Adjust the eye shields to an appropriate distance from the tool rests avoiding interference during operation.
CBG6250 Bench Grinder.fm Page 10 Thursday, November 10, 2011 3:26 PM OPERATION CAUTION: KEEP ALL BYSTANDERS A SAFE DISTANCE AWAY FROM THE TOOL AND NOT IN DIRECT LINE, FRONT OR BACK OF THE GRINDER. CAUTION: ALWAYS WEAR SAFETY GLASSES NOTE: Check that there is a 1.5 mm clearance between the tool rests and the surface of the grinding wheel. Adjust as necessary. NOTE: Check the gap between the spark deflectors and the surface of the grinding wheel. These should also be a maximum of 2 mm. Adjust as necessary.
CBG6250 Bench Grinder.fm Page 11 Thursday, November 10, 2011 3:26 PM MAINTENANCE REPLACING THE GRINDING WHEELS WARNING: DO NOT USE DAMAGED GRINDING WHEELS. WARNING: SWITCH THE GRINDER OFF AND DISCONNECT THE POWER SUPPLY BEFORE CHANGING THE GRINDING WHEELS 1. Loosen the screws shown and rotate and remove the cover. 2. Hold the other wheel by hand, and remove the nut and outer flange. NOTE: The left hand grinding wheel locking nut has a left handed thread. 3.
CBG6250 Bench Grinder.fm Page 12 Thursday, November 10, 2011 3:26 PM PARTS DIAGRAM 12 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CBG6250 Bench Grinder.
CBG6250 Bench Grinder.fm Page 14 Thursday, November 10, 2011 3:26 PM DECLARATION OF CONFORMITY 14 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CBG6250 Bench Grinder.fm Page 15 Thursday, November 10, 2011 3:26 PM NOTES 15 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CBG6250 Bench Grinder.
