BENCH GRINDER WITH LIGHT AND WHEEL DRESSER MODEL NO: CBG8370L PART NO: 6500532 OPERATION & MAINTENANCE INSTRUCTIONS LS0512
INTRODUCTION Thank you for purchasing this CLARKE Bench Grinder with light and wheel dresser. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
POWER TOOL SAFETY WARNINGS 1) WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY 1. Power tool plugs must match the outlet.
) POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct accessories for your application. The correct power tool will do the job better and safer at the rate which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3. Disconnect the plug from the power source before changing accessories, or storing power tools.
8. ALWAYS check for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it would operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the tool's operation. A part that is damaged should be properly repaired or replaced at an authorised service centre.
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
CARTON CONTENTS The following items should be supplied in the carton. If any parts are missing or damaged, please contact the Clarke dealer where you purchased the bench grinder.
BEFORE USE MOUNTING THE GRINDER ON A WORKBENCH NOTE: We highly recommend that you bolt this bench grinder securely to a workbench to gain maximum stability for your machine. 1. Using the base of the bench grinder as a template, mark the bench through the holes in the casting. 2. Bolt the bench grinder to the bench with bolts, washers and nuts (not supplied). 3. To reduce vibration, mount the bench grinder on a vibration absorbing mat. INSTALLING THE TOOL RESTS 1.
INSTALLING THE EYE SHIELDS 1. Attach the left eye shield arm to the bench grinder using the bracket, flat washer and bolt supplied. 2. Fit the lens to the lens holder as shown. NOTE: One of the lenes has a manifying window. 3. Repeat for right side eye shield. • Adjust the eye shields to an appropriate distance from the tool rests avoiding interference during operation. 9 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
OPERATION CAUTION: KEEP ALL BYSTANDERS A SAFE DISTANCE AWAY FROM THE TOOL AND NOT IN DIRECT LINE, FRONT OR BACK OF THE GRINDER. CAUTION: ALWAYS WEAR SAFETY GLASSES NOTE: Check that there is a 1.5 mm clearance between the tool rests and the surface of the grinding wheel. Adjust as necessary. NOTE: Check the gap between the spark deflectors and the surface of the grinding wheel. These should also be a maximum of 2 mm. Adjust as necessary.
SHARPENING TIPS SCISSORS If possible, take the scissors apart to make the sharpening operation easier and safer. Remove material only from the outside surface and work from the handle end of the blade toward the tip. KNIVES Remove metal equally from both faces, working from the handle end of the blade toward the tip. MAINTENANCE WARNING: DISCONNECT THE GRINDER FROM THE MAINS SUPPLY BEFORE FITTING REPLACEMENT WHEELS, CLEANING OR ADJUSTMENT.
REPLACING THE GRINDING WHEELS WARNING: DO NOT USE DAMAGED GRINDING WHEELS. WARNING: SWITCH THE GRINDER OFF AND DISCONNECT THE POWER SUPPLY BEFORE CHANGING THE GRINDING WHEELS 1. Loosen the screws shown and rotate and remove the cover. 2. Hold the other wheel by hand, and remove the nut and outer flange. NOTE: The left hand grinding wheel locking nut has a left handed thread. 3. Slide off the old wheel and replace with a new one.
PARTS DIAGRAM 13 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
PARTS LIST WACBG8370L01 37 Wheel(60#) WACBG8370L37 Left Guard Cover WACBG8370L02 38 Philips Screw WACBG8370L38 I type Hex Nut WACBG8370L03 39 Toothed Locking Washer WACBG8370L39 Wheel Flange WACBG8370L04 40 Philips Screw WACBG8370L40 WACBG8370L05 41 Cord bushing WACBG8370L41 Right Guard Inner Cover WACBG8370L42 1 Philips Screw Assembly 2 3 4 5 Wheel(36#) 6 Philips Screw WACBG8370L06 42 7 Standard Washer WACBG8370L07 43 I type Hex Nut WACBG8370L43 8 Left Guard inner Cove
DECLARATION OF CONFORMITY 15 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
