Model Nos CBM100SS, 130SS, 250SS, 240 & 240E CPE100P, 100TF, 120 & 130SS HANDY PUMP 2 OPERATING & MAINTENANCE INSTRUCTIONS © 0406
CONTENTS Safety Precautions ......................................................... 3 Electrical Connections .................................................. 4 Water Connections ....................................................... 5 Priming the Pump ........................................................... 7 Troubleshooting .............................................................. 8 Specifications ........................................................... 9 -11 Parts Lists and Diagrams ......
Thank you for purchasing this CLARKE Water Pump, which is a general purpose pump, suitable for a variety of applications involving the transfer of clean, cold water ONLY (up to a maximum of 35oC) - for domestic and gardening applications. This manual covers a range of pumps as shown on the front cover. Please read it thoroughly and ensure you are familiar with all aspects relating to your particular pump, before its’ connection and use.
ELECTRICAL CONNECTIONS WARNING THIS EQUIPMENT MUST BE EARTHED This appliance, which is provided with a 3-pin BS 1363 plug, should be connected to a standard domestic 13 amp, 230 volt (50Hz), electrical supply and we strongly recommend that this be done through a Residual Current Device (RCD). Should the plug require renewing at any time, the wires should be connected in accordance with the following colour code: Green & Yellow .............. Earth or marked with a letter “E” or Earth symbol “ ” Blue .....
WATER CONNECTIONS IMPORTANT: The pump must not be connected to the power supply until the hose/pipe installation is completed. If any part of the system is to be connected to the mains water supply, do ensure that you comply with your local water authority regulations. Because of the variety of possible installations, no plumbing accessories are supplied as standard with your pump, (except for the Handy Pump 2, which is provided with a 4 metre inlet hose complete with a foot valve and filter).
the suction side of the pump unless it is an isolator valve in a gravity fed system. It is IMPORTANT to note also, that these pumps should not be operated with the delivery valve completely closed. To prevent unnecessary strain or possible distortion to the pump, ensure that adequate support is provided to the hoses and/or pipes. Remember they will be considerably heavier when filled with water.
CPE100TF, CBM100SS, CBM130SS and CBM250SS These units are set up as a BOOSTER pumps by utilising an air chamber with a pressure regulator to provide a constant pressure at the outlet. All models are provided with non-return valves and Model CPE100TF is also provided with an inlet filter. The pumps will automatically cut in when the water pressure reduces to 2.0 Bar, and cut out when the pressure reaches 3.5 Bar. (These pressures are 3.5 and 5.2 bar respectively for Model CBM250SS).
TROUBLE SHOOTING REMEMBER that rate of flow is dependant upon the head - i.e. the greater the head the lower the flow. Check the specifications for your pump on pages 9 to 11. The pump does not run 1. No mains supply 2. Impeller seized / blocked Thermal overload has operated switching OFF 1. Incorrect mains voltage 2. Impeller seized / blocked 3. Pump ran with hot water 4. Pump ran dry Pump runs but no output 1. Air in pump housing 2. Suction fault 3. Suction height too great Low or no Flow 1.
SPECIFICATIONS CPE100P Motor ............................... Power .............................. Max. Flow ........................ Max. Head ...................... Max. Suction Height ...... Max Output Pressure ..... Part No. ........................... Weight ............................. 230V 50Hz 700 Watts 50 Litres/min 42 Metres 9 Metres 6 Bar 7230630 6.8 Kg CPE100TF Motor ............................... Power .............................. Max. Flow ........................ Max. Head ..............
CPE130SS Motor ............................... Power .............................. Max. Flow ........................ Max. Head ...................... Max. Suction Height ...... Part No. ........................... Weight ............................. 230V 50Hz 1250 Watts 81 L/min 50 Metres 9 Metres 7230680 19.6 Kg CBM 240 & 240E Motor ............................... Power ............................... Max. Flow ........................ Max. Head (240) .............. Max Head (240E) ............ Max.
CBM100SS Motor ............................. 230V 50Hz Power ............................ 700 Watts Max. Flow ...................... 51 L/min Max. Head .................... 35 Metres Max. Suction Height .... 9 Metres Air Reservoir .................. 24 Litres ON/OFF Pressure .......... 2.0/3.5 Bar Part No. ......................... 7238000 Weight ........................... 15.2 Kg CBM130SS Motor ............................ 230V 50Hz Power ........................... 1250 Watts Max. Flow .................
CPE100P 12
CPE100P Item Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Qty Pump Housing Cap 3/8" Gas Joint O-ring Screw Washer Joint O-ring Injector Diffuser Joint 0-ring Impeller Mechanical Seal Flange With Handle Nut Joint Flange Bearings Shaft w/Bearings Stator Gasket Base Capacitor Holder Capacitor Screw Joint O-ring Screw Cap Capacitor Cable Fastener Screw Spring Washer Washer Spring Ring Cap MEC63 Fan MEC 63 Fan Cover MEC63 Cross
CPE100TF 14
CPE100TF No. Description Qty Part No. No. Description Qty Part No. 1 Joint ............................... 1 .. LDP1240006 2 Nipple ........................... 1 .. LDS3500202 33 Washer .......................... 1 .. LDP1120051 3 Joint ............................... 1 .. LDP1240010 34 Spring ring ..................... 1 .. LDP1120002 32 Screw ............................ 1 .. LDP1100055 4 Flexible Pipe ................. 1 .. LDP1590005 35 Rear Shield Mech 63 ... 1 ..
CPE130SS 16
CPE130SS Item Description Qty Part No. 1 ........... Pump Housing ............................................................. 1 ............... LDS3220002 2 ........... Screw 3/8" Gas ............................................................ 2 ............... LDS3500009 3 ........... Joint O-Ring ................................................................. 2 ............... LDP1200004 4 ........... Screw ............................................................................ 8 ...........
CPE120 18
CPE120 Item Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Qty Pump Housing ....................................................................... 1 Screw 3/8" Gas ...................................................................... 2 Joint O-Ring ........................................................................... 2 Screw ......................................................................................
CBM240 20
CBM240 No. Description Qty Part No. No. Description Qty Part No. 1 Flange Mc 1" Gas ............. LDS3500280 28 Bearing ............................... LDP1180006 2 Screw 3/8" Gas .................. LDS3500009 29 Shaft With Bearings ........... LDS3111009 3 Joint O.ring ........................ LDP1200004 30 Stator .................................. LDS3410207 4 Cross Screw ........................ LDP1100040 31 Gasket 63/71 ..................... LDS3500199 5 Spring-washer ...............
CBM240E 22
CBM240E No. Description Qty Part No. No. Description Qty Part No.
HANDY PUMP 2 24
HANDY PUMP 2 Item Description Qty Part Number 1 ............. Pump Housing ........................................................ 1 ................ LDS3220002 2 ............. Screw 3/8" Gas ....................................................... 2 ................ LDS3500009 3 ............. Joint O-Ring ............................................................ 2 ................ PLD1200004 4 ............. Screw ....................................................................... 8 .............
CBM100SS & CBM 130SS 26
CBM100SS & CBM 130SS No. Description Qty Part No, No. Description Qty Part No, 1 Pump housing LPS3220002 30 Screw LPP1100006 2 Joint O.
CBM250SS CBM250SS 28
CBM250SS No.
ACCESSORIES Please contact your CLARKE dealer who will be happy to advise you regarding the accessories listed below. 1” Foot Valve Filter ................................................................... 7950561 1” BSP Spigot Hose Connector ............................................... 7950210 1” I.D. Reinforced Hose for suction and delivery. ................ 7955010 1” I.D. Layflat Hose for delivery only. ..................................... 7955110 Non-Return Valve (male/female for CPE100P) .......
