WARNING: Read these instructions before using the machine CORDLESS ROTARY TOOL KIT MODEL NO: CCRT266 PART NO: 6461901 OPERATION & MAINTENANCE INSTRUCTIONS LS0911
INTRODUCTION Thank you for purchasing this cordless rotary tool kit. Please read this manual thoroughly, before attempting to operate, and carefully follow all instructions given. It is vitally important that ALL precautions are taken, as specified, which will not only provide protection for yourself and that of others around you, but will also ensure that the product will give you long and satisfactory service.
SAFETY PRECAUTIONS WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/ OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED BELOW REFERS TO YOUR BATTERY OPERATED (CORDLESS) POWER TOOL. WORK AREA 1. Keep work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool for your application.
ADDITIONAL SAFETY INSTRUCTIONS FOR ROTARY TOOLS 1. Only use accessories supplied for use with this tool. 2. Never use worn or cracked accessories. 3. Hold the tool away from your face when switching on. 4. Keep your fingers away from rotating accessories. 5. Be careful not to accidently hit any foreign objects in the workpiece. 6. If an accessory jams, switch the tool off and disconnect the battery before attempting to free the accessory. 7.
17. Ensure that sparks resulting from use do not create a hazard e.g. do not hit persons, or ignite flammable substances. 18. Ensure ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the battery from the rotary tool. 19. Personal protective equipment such as dust masks and gloves should be worn as appropriate. 20. Remember the wheel continues to rotate after the tool is switched off.
THE BATTERY NOTES ON CHARGING • During use, the battery pack may become warm. Allow it to cool before recharging. • Never store the battery pack when it is discharged, recharge it fully before storage. TO REMOVE THE BATTERY • Press either side of the battery and pull it out of the rotary tool. TO CHARGE THE BATTERY 1. Slide it into the charger unit. • Make sure that the battery is fully inserted. • The red LED will light to show that the battery is charging. 2.
INSERTING THE BATTERY 1. Align the battery with the base of the handle and slide it into the locating clip. • Make sure that the battery pack is fully located and clicks into place. BEFORE USE FITTING DISCS & GRINDING STONES TO THE MANDREL Mount the selected disc on to the mandrel as shown, ensuring the two washers are in place. • DO NOT overtighten the screw. ASSEMBLING POLISHING CLOTH WHEELS Screw the cloth wheel on to the mandrel firmly, but do not overtighten it.
FITTING A COLLET WARNING: MAKE SURE THAT THE BATTERY HAS BEEN REMOVED FROM THE ROTARY TOOL BEFORE REMOVING, OR FITTING A COLLET OR ACCESSORY The rotary tool is supplied with 4 interchangeable collets; 0.8mm - 1.6mm - 2.4mm and 3.2mm (fitted to the rotary tool). Select the collet to be fitted according to the shaft size of the mandrel or accessory to be used. To fit a collet, proceed as follows. 1. Press and hold down the spindle lock.
FITTING AN ACCESSORY IMPORTANT: Ensure the tool is switched OFF TO FIT AN ACCESSORY, PROCEED AS FOLLOWS. 1. Make sure that the correct size collet has been fitted. 2. Press and hold down the spindle lock. • It may be necessary to rotate the chuck to fully engage the spindle lock. 3. Rotate the chuck sleeve in an anticlockwise direction until the collet jaws are open sufficiently to accept the accessory. 4. Insert the accessory into the collet as far as it will go. 5.
OPERATING INSTRUCTIONS OPERATING THE ROTARY TOOL WARNING: BEFORE OPERATING THE ON/OFF SWITCH, MAKE SURE THAT THE COLLET AND ACCESSORIES HAVE BEEN CORRECTLY AND SECURELY FITTED. 1. To switch the rotary tool on, rotate the speed control away from 0. 2. Select a suitable speed using the speed controller. • The low speed settings should be used for removing rust, and polishing. • The medium speed settings should be used for drilling, engraving, sharpening and removing paint.
CLEANING AND MAINTENANCE WARNING: MAKE SURE THAT THE BATTERY HAS BEEN REMOVED FROM THE ROTARY TOOL BEFORE STARTING ANY CLEANING, OR MAINTENANCE PROCEDURES. • After use, thoroughly clean all excess chippings and dust from the rotary tool, taking special care to clean the cooling vents. • Clean the spindle lock, the chuck and the spindle collar. • Keep all accessories sharp and clean. • There are no user serviceable parts inside this rotary tool.
DECLARATION OF CONFORMITY 13 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
PARTS LIST Part Part number Part Part number 1 x Cordless Grinder ETCCRT26601 3x Aluminium oxide grinding wheel with shank ETCCRT26613 1 x Charger Base ETCCRT26602 2 x Silicon carbide grinding wheel with shank ETCCRT26614 1 x Adaptor 12V AC 500mAh ETCCRT26603 6 x Diamond wheel points 1/8” shank ETCCRT26615 1 x Battery 700mAh ETCCRT26604 1 x HSS cutter ETCCRT26616 1 x Polishing Compound ETCCRT26605 2 x Polished HSS twist drills 1/16” ETCCRT26617 30 x Cut off wheel Heavy Duty 1 5/16" x
ADVERTISEMENT For heavier duty work you may be interested in our mains powered rotary tool set Model number CRT40. Also available is our CRT100A- 100pc Accessory Kit for CRT40 This is available from you Clarke dealer 15 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
