ELECTRIC STAPLER & NAILER MODEL NO: CESNG1 PART NO: 6462560 OPERATION & MAINTENANCE INSTRUCTIONS LS1013
INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS, INCLUDING THE FOLLOWING, SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY. WARNING: READ ALL THESE INSTRUCTIONS BEFORE OPERATING THIS PRODUCT AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. For safe operations: 1. Keep work area clean. - Cluttered areas and benches invite injuries. 2. Consider work area environment. - Do not expose power tools to rain.
periodically and replace, if damaged. Keep handles dry, clean and free from oil and grease. 14. Disconnect tools. - When not in use, before servicing and when changing accessories such as blades, bits and cutters. 15. Avoid unintentional starting. - Do not carry a tool with a finger on the switch. 16. Use outdoor extension leads. - When tool is used outdoors, use only extension cables intended for outdoor use. 17. Stay alert. - Watch what you are doing. Use common sense.
SAFETY SYMBOLS Read manual before use Wear suitable eye protection SAFETY SYSTEM FULL SEQUENTIAL ACTUATION This stapler/nailer has an actuation system in which the trigger and safety yoke are linked in such a way that it will only operate if the trigger is pulled after the safety yoke (muzzle) has been applied to the work. Further driving operations require the user to release the trigger and lift the safety yoke (muzzle) away from the workpiece before the next use.
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply through an approved BS1363/A plug fitted with a BS1362 fuse. If the plug has to be changed because of damage, it must be removed and a replacement fitted, following the wiring instructions shown below.
PREPARING THE STAPLER/NAILER FOR USE FILLING THE MAGAZINE WARNING: SWITCH OFF THE STAPLER/NAILER AND REMOVE THE PLUG FROM THE MAINS POWER SUPPLY BEFORE FILLING THE MAGAZINE. CAUTION: KEEP YOUR FINGERS WELL AWAY FROM THE TRIGGER, 1. Press and hold the magazine catch (1) then pull out the magazine (2). 2. Turn over the stapler/nailer and insert the staple strip or the nail strip. • Hold the stapler/nailer at a slight angle while inserting the nail strip so that nails rest against the side wall.
USING THE STAPLER/NAILER 1. Pay attention to all of the safety warnings in these operating instructions. 2. Set the ON/OFF switch to the ON position. 3. Press the stapler/nailer against the work and pull the trigger. • Always hold the stapler/nailer square to the workpiece, never at an angle. 4. Release the trigger and lift the stapler/nailer away from the workpiece. 5. Repeat steps 3-4 as required. 6.
MAINTENANCE WARNING: SWITCH OFF THE STAPLER/NAILER AND REMOVE THE PLUG FROM THE MAINS POWER SUPPLY BEFORE CARRYING OUT ANY SERVICING OR MAINTENANCE • The stapler/nailer does not require any specific maintenance other then keeping it free from any dirt or debris. This can be done using a clean dry cloth and/or brush. Do not use solvent or alcohol based cleaner as it could damage the casing. • There are no user serviceable parts on the stapler/nailer.
SPECIFICATION Input Voltage 230V, 50Hz, 1Ph Max Firing Speed 20 shots/min. Maximum Magazine Capacity 100 Nails or 100 Staples Nail Type 18 gauge/ 15mm Brad Nail Staple Type 22 gauge (Type 53) - 6mm, 8mm, 10mm Dimensions 280 x 170 x 65 mm Weight 1.28 kg Activation Mode Full Sequential Actuation Noise Characteristic Values In Accordance With EN12549. Sound Pressure: 73.3 dB(A) Sound Power Measured LwA 86.3dBLwA Vibration Characteristic Values In Accordance With ISO 8662-1 1: 1999 2.
DECLARATION OF CONFORMITY 11 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
