34o Clipped Head Air Frame Nailer MODEL: CFN34 Part No.
SPECIFICATIONS Min. Hose Size (ID) .................................... 6 mm (1/4”) Ave. Air Consumption .............................. 14.8 cfm Operating Pressure .................................. 5.51 - 7.58bar (80 - 110psi) Air Pressure Max ....................................... 8.27 bar (120 psi) Nail Size ...................................................... 50-90 mm Magazine Capacity ................................ 80 Drive Speed ..............................................
Thank you for purchasing this Clarke Frame Nailer. Please read these instructions carefully before attempting to use the tool, to ensure the safety of yourself and others that may be in the vicinity, and also to ensure the tool provides you with years of satisfactory service. GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.
SAFETY PRECAUTIONS WARNING COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE THOROUGHLY FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. • Keep the work area clean and tidy. • Keep children and visitors away - Do not let children handle the nailer. Make sure that any other persons in the work area are dressed suitably and are wearing eye and ear protectors.
SAFETY PRECAUTIONS cont.: • Always disconnect from the air supply when: a) Performing any maintenance such as clearing a jammed nail. b) The nailer is not in use. c) The nailer will be left unattended. d) Moving to another work area. e) Passing the nailer to another person. • Use only the nails, parts and accessories described in this book. • Only carry out the maintenance recommended in this booklet. For replacement of parts or repair, return the nail gun to the place of purchase.
PREPARATION FOR USE Screw the quick fit air intake coupling to the nailer as shown on the right. Preliminary checks Make sure that the air supply is not connected to the nailer. Do not put any nails in the air nail gun until directed to do so in the following procedure. 1. It is essential that the air nail gun is lubricated before each use. Use the CLARKE Air Line Oil provided with your nailer to lubricate the safety yoke and trigger mechanism.
LOADING NAILS Always disconnect the nailer from the air supply before loading nails. 1. Pull the nail pusher back as far as possible until the catch clicks into place. 2. Slide the nails through the loading slot into the magazine as shown. 3. Press the release latch on the rear of the magazine and slide the nail pusher forward. • Your nailer is now ready to use. OPERATION 1. Turn ON the air supply, and check for air leaks. • 2. If any are apparent, rectify before proceeding.
Avoid triggering the nailer when the nail magazine is empty. If the nailer operates improperly or is defective, disconnect from the air supply and have the tool inspected by a qualified service technician. In the event of long breaks in work or at the end of the working session, disconnect the tool from the air supply and empty the nail magazine. Disconnecting the air supply WARNING! NEVER DISCONNECT THE AIR SUPPLY HOSE UNTIL THE COMPRESSOR HAS BEEN SHUT DOWN AND THE COMPRESSED AIR RELEASED. 1.
MAINTENANCE WARNING! MAKE SURE THAT THE AIR NAIL GUN IS DISCONNECTED FROM THE AIR SUPPLY BEFORE STARTING ANY CLEANING, OR MAINTENANCE PROCEDURES. LUBRICATION • Only use the oil provided to lubricate the air nail gun. • Lubricate the moving parts of the safety yoke and trigger mechanism before using the nailer. • Do not use detergent oils or any oil that contains artificial additives as these may cause the nailer to malfunction.
PARTS DIAGRAM 10
PARTS LIST No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Bolt M8X30 Air deflector Deflector rubber Spring Spring wire Bolt M6X30 Spring washer Flat washer Cylinder core Bolt M5X5 Cylinder cover O-ring 41.7x3 O-ring 56x3.1 Head valve Piston Spring seat Compressed spring Spring washer Collar O-ring 42.3x5 Main Piston O-ring 57.
