RECIPROCATING SAW Part No. 6460200 MODEL No. CON100 Part No.
Thank you for purchasing this CLARKE Reciprocating Saw. Before attempting to use the reciprocating saw, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the reciprocating saw giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
GENERAL SAFETY PRECAUTIONS WARNING: As with all machinery, there are certain hazards involved with their operation and use. Exercising respect and caution will considerably lessen the risk of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator or damage to property, may result. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. ALWAYS Learn the machines’ applications, limitations and the specific potential hazards peculiar to it.
GENERAL SAFETY PRECAUTIONS 16. 17. 18. 19. 20. ALWAYS remove plug from electrical outlet when adjusting, changing parts, or working on the machine. NEVER operate machine while under the influence of drugs, alcohol or medication. NEVER leave machine running unattended. Turn power off. Do not leave the machine until it comes to a complete stop. NEVER force the machine. It will do a better and safer job at the rate for which it was designed.
ELECTRICAL CONNECTIONS This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing at any time, ensure that a plug of identical specification is used.
BEFORE USE FITTING THE BLADE WARNING! Before removing, or installing a blade, make sure that the mains plug has been removed from the mains supply. Shoe adjustment screws 1. Loosen the blade securing screw, using the hexagonal key provided. 2. With the blade teeth facing downwards, push the blade shank into the blade locating clip as far as possible. 3. Fully tighten the blade securing screw. Blade securing screw ADJUSTING THE SHOE 1.
OPERATION ON/OFF SWITCH 1. Slide the trigger switch down and back. Trigger switch The saw will run at the speed selected with the variable speed selector. 2. To switch off the reciprocating saw, release the trigger switch. WARNING! The blade will continue to run for a short period after the trigger has been release. Wait until it stops before removing it from the workpiece. WARNING! If the cutting operation is dusty, we recommend that you use a dust mask.
OPERATION PENDULUM SWITCH The pendulum switch adjusts the cutting stroke for each type of material. This improves the quality of the cut, and increases the blade life. Position Wood Metal Plastics 3 Fast cuts - PVC 2 Thick workpieces - Fibreglass 1 Plywood Aluminium - Chipboard Non-ferrous - Thin Workpieces Sheet metal - Acrylic 0 Fine Cuts To adjust the pendulum setting 1. Rotate the pendulum switch to the desired setting. Use the table above to select the correct setting.
OPERATION TIPS Cutting wood • Clamp the workpiece securely and remove all nails and metal objects. • Holding the tool with both hands, work with the saw shoe pressed against the workpiece. Plunge cutting in wood • Rest the saw shoe on the workpiece in such a position that the blade forms an appropriate angle for the plunge cut. • Switch on the tool and feed the blade into the material at full speed, make sure that the saw shoe remains in contact with the workpiece at all times.
MAINTENANCE WARNING! Before performing any maintenance tasks make sure that the mains plug has been removed from the mains supply. • After use, clean all dust and wood chippings from the reciprocating saw. • Clean all of the ventilation slots on the motor housing. • Make sure that the shoe is free from dirt and grease. • Keep the handle clean and free from oil and grease. • Resin and glue on the blade causes poor cutting results. Clean the blade after use.
PARTS DIAGRAM PARTS & SERVICE For Spare Parts and Service, please contact your nearest dealer, or CLARKE International, on one of the following numbers. PARTS & SERVICE TEL: 020 8988 7400 or e-mail as follows: PARTS: parts@clarkeinternational.com SERVICE: service@clarkeinternational.
PARTS LIST Available as a Spare part Description 1 KPCON10001 Tapping Screw Yes 32 KPCON10032 Screw Yes 2 KPCON10002 Spring Washer Yes 33 KPCON10033 Washer Yes Item Part Item Number Available as a Spare part Part Number Description 3 KPCON10003 Screw Yes 34 KPCON10034 Socket Head Screw Yes 4 KPCON10004 Cove Plate Assembly Yes 35 KPCON10035 Localising Pin Yes 5 KPCON10005 Blade Clamp Screw Yes 36 KPCON10036 Pendulum Selector Yes 6 KPCON10006 Blade Clamp Plate
VIBRATION EMISSIONS HAND-ARM VIBRATION Employers are advised to refer to the HSE publication “Guide for Employers”. All hand held power tools vibrate to some extent, and this vibration is transmitted to the operator via the handle, or hand used to steady the tool. Vibration from about 2 to 1500 hertz is potentially damaging and is most hazardous in the range from about 5 to 20 hertz.
VIBRATION EMISSIONS You will note that a third value is given in the specification - the highest measured reading in a single plane. This is the maximum level of vibration measured during testing in one of the axes, and this should also be taken into account when making a risk assessment. 2 ‘a’ values in excess of 2.5 m/s are considered hazardous when used for 2 prolonged periods. A tool with a vibration value of 2.
DECLARATION OF CONFORMITY When disposing of this product, ensure it is disposed of according to all local ordinances. It must not be disposed of with general household waste.
