4½” (115mm) ANGLE GRINDER Model No.
SPECIFICATIONS Motor ............................................................. 230V~ 50Hz 1ph Power Rating ................................................. 1010Watts Fuse Rating .................................................... 13Amps No Load Speed ............................................. 11,000RPM Wheel/Disc Dia. ............................................ 115mm Bore ................................................................ 22mm Sound Power Level .......................................
Thank you for selecting this CLARKE 115mm (4½”) Angle Grinder. Before attempting to use the tool, please read this leaflet thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the Angle Grinder giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
2. ALWAYS ensure that ADEQUATE LIGHTING is available. A minimum intensity of 300 lux should be provided. Ensure that lighting is placed so that you will not be working in your own shadow. 3. CHECK FOR DAMAGE. Before using the tool, any damaged part should be checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, breakage of parts, mountings and any other condition that may affect the tools’ operation.
ADDITIONAL PRECAUTIONS FOR ANGLE GRINDERS 1. It is strongly advised that you wear ear protectors/defenders as the noise level during operation, depending upon the work being carried out, can exceed safe working levels. 2. Always wear a good pair of industrial gloves to avoid potential injury from sparks and debris. 3. Do not use the tool if the electric cable, plug or motor is in poor condition. 4.
24. NEVER use a cutting-off wheel for side grinding. 25. ALWAYS ensure the work is properly secured or supported. 26. Do not allow flying sparks to fall on sensitive areas. Be aware of fire risks. 27. When not in use always store in a dry clean environment and out of reach of children. Additionally, ALWAYS keep these instructions in a safe place for future reference.
FEATURES (Ref. Fig 1) 1. ON/OFF Switch (A) The ON/OFF switch (A) is provided with a safety lock button (B). The lock button (B) must be held in before the trigger can be squeezed in to the ‘ON’ position. This is designed to prevent accidental starting. . Fig 1. Fig 1. 2.
2. Hand Grip A threaded hole ‘E’, on the top, left or right hand side of the gear housing, is provided so that the hand grip may be screwed in, as required, to provide left or right hand control of the tool. OPERATION IMPORTANT: DO NOT plug the tool in to the mains, unless you have ensured it is switched OFF and the guard is set to the desired position. The blade guard can be rotated about its axis and is locked by a single hex head screw (see Fig.3).
TROUBLESHOOTING Problem Possible Cause Tool will not operate 1. No supply Remedy 1. Check supply and rectify where necessary. 2. Switch is faulty 2. Consult your Clarke dealer 3. Fuse blown 3. Check and replace if necessary. If condition persists, consult your dealer 4. Motor faulty 4. Consult your Clarke dealer. Motor runs but disc 1. Flange nut not tight 1. Tighten flange nut will not 2. Gear shaft or key broken 2. Consult your Clarke dealer Heavy internal 1. Faulty motor 1.
PARTS DIAGRAM SPARE PARTS 1. 2. Hand Grip Guard HTCON11501 HTCON11502 3. 4. Friction Washer Inner Flange HTCON11503 HTCON11504 5. 6. Grinding Wheel/Cutting Disc Outer Flange (See below) HTCON11506 7. 8. Guard Securing Screw Guard Locking Screw HTCON11507 HTCON11508 - Flange Release Tool HTCON11509 The following Grinding Wheels/ Cutting Discs are available from your Clarke dealer. 1. Metal Grinding (DPC) 115mm x 6mm thickness Part No: 6470705 2. 3.
