WALL CHASER MODEL NO: CON1450WC PART NO: 6462165 OPERATION & MAINTENANCE INSTRUCTIONS LS0109
INTRODUCTION Thank you for purchasing this CLARKE Wall Chaser. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
GENERAL SAFETY RULES WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/ OR SERIOUS INJURY. SAVE THESE INSTRUCTIONS. WORK AREA 1. Keep work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3.
POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools.
KICKBACK AND RELATED WARNINGS Kickback is a sudden reaction to a pinched or snagged cutting disc. Pinching or snagging causes rapid stalling of the rotating wheel which in turn causes the uncontrolled power tool to be forced in the opposite direction of the wheels rotation. 1. Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up.
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
BEFORE USE WHAT’S SUPPLIED Unpack your wall chaser and make sure that the following items are present. Should there be any damage caused during transit contact your Clarke dealer immediately. • 1 x Wall Chaser • 1 x Pin Spanner • 1 x Attachable Handle • 1 x Breakout Chisel • 1 x 5mm Hex Key • 1 x Dust Extraction Attachment • 2 x Cutting Discs (150mm Diameter x 22.2mm Bore) SPINDLE LOCK BUTTON.
REPLACING THE CUTTING DISCS WARNING: Disconnect the plug from the power source before making any adjustments or changing accessories. NOTE: Always replace both discs at the same time. 1. Remove the depth adjustment knob by hand and 3 bolts indicated using the 5mm hex key supplied. 2. Lift off the side plate. Side plate 3. Press and hold the spindle lock button. 4.
FITTING THE DUST EXTRACTION ASSEMBLY Attach the dust extraction assembly to the wall chaser. • Insert the assembly (1) into the extraction port (2) and rotate slightly clockwise to lock into place. • Remove the collar (4) and slide it over the vacuum cleaner hose. • Push the hose onto the dust extraction tube (3). • Secure in place by tightening up the collar (4). FITTING THE ATTACHABLE HANDLE Screw the handle (5) into the hole (6) shown on the wall chaser.
OPERATION ADJUSTING THE CUTTING DEPTH 1. Loosen the depth adjustment knob. 2. Raise/lower the baseplate. 3. Use a ruler as shown to measure the depth of the blade (d). 4. Tighten the depth adjustment knob. NOTE: The depth of cut should be 3mm deeper than the required slot depth, this is to compensate for any inaccuracies when you break away the resulting fin after cutting.
MAINTENANCE WARNING: MAKE SURE THAT THE WALL CHASER IS SWITCHED OFF AND DISCONNECTED FROM THE MAINS SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE PROCEDURES. With the exception of changing the blade there are no user serviceable parts in this unit. After use, • Clean away any accumulated dust. • Check the condition of the cutting disc for signs of cracking, and discard immediately if apparent. • Keep the cooling vents clear. • Clean the housing with a soft cloth.
SPECIFICATIONS CON1450WC Electrical Supply 230V @ 50Hz Power Rating 1450W Part Number 6462165 Disc Bore 22.2 mm Disc Diameter 150 mm Disc Thickness 2.5 mm Cutting Depth 8-40 mm Cutting Width 8-30 mm Guaranteed Sound Power dB LWa 106.9 dB Vibration <2.
EXPLODED DIAGRAM - PARTS LIST 13
EXPLODED DIAGRAM - PARTS LIST NO DESCRIPTION PART NO NO DESCRIPTION PART NO 1 Dust extraction CON1450WC01 43 Roll sheath CON1450WC43 2 Rubber ring CON1450WC02 44 Washer CON1450WC44 3 Pree ring CON1450WC03 45 Shaft CON1450WC45 4 Bend tube CON1450WC04 46 Circlip CON1450WC46 5 Sealed ring CON1450WC05 47 Washer CON1450WC47 6 Connect tube CON1450WC06 48 Pinion gear CON1450WC48 7 Aluminium connect CON1450WC07 49 Bearing CON1450WC49 50 Screw CON1450WC50 8 Screw
DECLARATION OF CONFORMITY 15