SANDER/POLISHER MODEL NO: CP180 PART No: 6462105 OPERATION & MAINTENANCE INSTRUCTIONS gc0811
Thank you for purchasing this CLARKE Sander/Polisher, which is designed for DIY use. Before attempting to use the machine, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the product giving you long and satisfactory service. Guarantee This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
Safety Precautions WARNING: As with all machinery, there are certain hazards involved with their operation and use. Exercising respect and caution will considerably lessen the risk of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator or damage to property, may result. 1. ALWAYS Learn the machine’s applications, limitations and the specific potential hazards peculiar to it. Read and become familiar with the entire operating manual. 2.
Electrical Connections Connect the mains lead to a standard 230V (50Hz) electrical supply through an approved 13 Amp BS1363 plug or a suitably fused isolator switch.
Overview ‘D’ Handle Speed Control Trigger Lock Trigger Spindle Lock Motor Brush Side Handle Backing Pad Polishing Hood Fig. 1 Assembly Before assembling the sander/polisher, check for missing parts and or damage caused in transit. Any defects must be reported to the Clarke dealer where the tool was originally purchased as soon as possible.
When the handle is in place, secure it in position with two allen screws and tighten the screws using an 8mm Allen key. DO NOT overtighten. 2 Side Handle Only To use the side handle only, screw into the D shaped boss on either side of the body, depending whether the tool is to be used left or right handed. See Fig. 3. DO NOT overtighten. 3 Fig. 3 Both Handles To fit both handles, Fit the ‘D’ Handle as described in section 1. Only fit one Allen screw to the longest side of the handle as shown in Fig.
Operation When using this tool, always hold it firmly with both hands. Before switching the tool on, always check for damage/missing parts etc. Any defects must be rectified before continuing. Whether polishing or sanding, always ensure the workpiece is securely fixed, i.e. clamped to workbench or secured in a vice. When working on car bodywork, always ensure that there is no possibility of loose items being left on the car bonnet, boot or roof.
HAND-ARM VIBRATION Employers are advised to refer to the HSE publication “Guide for Employers”. All hand held power tools vibrate to some extent, and this vibration is transmitted to the operator via the handle, or hand used to steady the tool. Vibration from about 2 to 1500 Herz is potentially damaging and is most hazardous in the range from about 5 to 20 Herz.
Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 501 502 503 504 505 506 507 Part No HT18001 HT18002 HT18003 HT18004 HT18005 HT18006 HT18007 HT18008 HT18009 HT18010 HT18011 HT18012 HT18013 HT18014 HT18015 HT18016 HT18017 HT18018 HT18019 HT18020 HT18021 HT18022 HT18023 HT18024 HT18025 HT18026 HT18027 HT18028 HT18029 HT18030 HT18031 HT18032 HT18033 HT18034 HT18035 HT18036 HT18037 HT18038 HT18039 HT1
Parts Diagram IMPORTANT: The use of parts other than CLARKE replacement parts may result in safety hazards, decreased tool performance and may invalidate your warranty.
