CPF13 Electric Power File.
CPF13 Electric Power File.fm Page 2 Wednesday, February 29, 2012 10:50 AM INTRODUCTION Thank you for purchasing this CLARKE Electric Power File. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
CPF13 Electric Power File.fm Page 3 Wednesday, February 29, 2012 10:50 AM POWER TOOL SAFETY WARNINGS WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY 1.
CPF13 Electric Power File.fm Page 4 Wednesday, February 29, 2012 10:50 AM POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct accessories for your application. The correct power tool will do the job better and safer at the rate which it was designed for. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3.
CPF13 Electric Power File.fm Page 5 Wednesday, February 29, 2012 10:50 AM EXPLANATION OF SYMBOLS & PICTOGRAMS Read Instruction Manual Before Use. Wear safety glasses or goggles when using the tool. Wear ear protection when using this tool. Always wear gloves when working with metal workpieces. Wear a dust mask. 5 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CPF13 Electric Power File.fm Page 6 Wednesday, February 29, 2012 10:50 AM ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.
CPF13 Electric Power File.fm Page 7 Wednesday, February 29, 2012 10:50 AM PART IDENTIFICATION. 1 Belt Tensioning Lever 6 Carbon Brush Cap 2 Arm Adjustment Lever 7 Dustbag 3 Variable Speed Control Knob 8 Belt Tracking Knob 4 Safety Lock Button 9 Arm 5 On/off Trigger Switch CARTON CONTENTS The following items should be supplied in the carton. If any parts are missing or damaged, please contact the Clarke dealer where you purchased the tool.
CPF13 Electric Power File.fm Page 8 Wednesday, February 29, 2012 10:50 AM ASSEMBLY WARNING: BEFORE ASSEMBLY, MAKE SURE THAT THE TOOL IS SWITCHED OFF AND UNPLUGGED. FITTING AND REMOVING SANDING BELTS 1. Move the belt tensioning lever to the front position. 2. Place the sanding belt over the front pulley and the rear pulley, sliding it through the slot in the housing • Make sure that the arrows on the inside of the sanding belt face the same direction as the arrows on the housing. 3.
CPF13 Electric Power File.fm Page 9 Wednesday, February 29, 2012 10:50 AM ADJUSTING THE SANDING BELT TRACKING 1. Switch the tool on. 2. Turn the belt tracking knob as required until the sanding belt runs straight along the length of the arm. FITTING AND REMOVING THE DUST BAG WARNING: ALWAYS REMOVE THE DUSTBAG WHEN USING THE TOOL ON METAL WORKPIECES. FITTING 1. Fit the dust bag over the dust extraction outlet. REMOVING / EMPTYING THE DUSTBAG The dustbag should be emptied when full. 1.
CPF13 Electric Power File.fm Page 10 Wednesday, February 29, 2012 10:50 AM USE INTENDED USE Your power file has been designed for sanding wood, metal, plastics and painted surfaces only. SWITCHING ON AND OFF To switch the tool on, press the on/off trigger switch. To switch the tool off, release the on/ off trigger switch. FOR CONTINUOUS OPERATION: 1. Press the on/off trigger switch. 2. Press the lock-on button. 3. Release the on/off trigger switch. 4.
CPF13 Electric Power File.fm Page 11 Wednesday, February 29, 2012 10:50 AM ADJUSTING THE ANGLE To adjust the angle of the arm. 1. Loosen the arm adjustment lever. 2. Adjust the arm to one of the 14 positions from +30o to -90o. 3. Move the arm adjustment lever to the lock position. HINTS FOR OPTIMUM USE • Always hold the tool securely. • Do not exert too much pressure on the tool. • Regularly check the condition of the sanding belt and replace when necessary.
CPF13 Electric Power File.fm Page 12 Wednesday, February 29, 2012 10:50 AM MAINTENANCE WARNING: BEFORE PERFORMING ANY MAINTENANCE, SWITCH OFF AND UNPLUG THE TOOL. • Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. • Regularly clean the ventilation slots in your tool using a soft dry brush or dry cloth. • Regularly clean the motor housing using a clean damp cloth.
CPF13 Electric Power File.fm Page 13 Wednesday, February 29, 2012 10:50 AM PARTS DIAGRAM 13 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CPF13 Electric Power File.
CPF13 Electric Power File.fm Page 15 Wednesday, February 29, 2012 10:50 AM DECLARATION OF CONFORMITY 15 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CPF13 Electric Power File.fm Page 16 Wednesday, February 29, 2012 10:50 AM 16 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
CPF13 Electric Power File.
