COLD WATER WASHER Model Nos. ELS145, 145R & ELS160R Part Nos.
SPECIFICATIONS ELS145 & 145R ELS160R 230V 50Hz 230V 50hz Power Rating 2500W 2700W Fuse Rating l3Amps l3Amps Noise Level - Guaranteed 91dBLWA 94dBLWA Motor Max. Pump Pressure 140bar 150bar Water Flow Rate 8 L/min 8.7L/min 3litres 3litres 465x515x930mm 465x515x930mm 25kg/26kg 29kg Detergent tank Capacity Dimensions Weight Please note that the details and specifications contained herein are correct at the time of going to print.
Thank you for purchasing this CLARKE COLD WATER WASHER. This machine is a lightweight, portable, high pressure power washer, designed for general DIY and LIGHT INDUSTRIAL use. These washers are ideal for cleaning greasy engines, garden furniture or removing oil spots from driveways/patios etc. The washer comprises an electric motor, pump, a high pressure hose with a trigger and lance, and provision for use with foam or cleaning agents.
SAFETY PRECAUTIONS WARNING Water at high pressure can be dangerous and may cause severe damage to persons or property if subject to misuse. NEVER allow anyone to operate this equipment unless they are thoroughly reliable, and completely familiar with the safety precautions. 1. Never direct the spray jet at any person or animal. 2. Never hold a finger over the high pressure nozzle. 3. Never direct the spray jet at the machine itself or any other electrical equipment. 4.
ELECTRICAL CONNECTIONS WARNING: THIS MACHINE MUST BE EARTHED. This product is provided with a standard 13 amp, 230 volt (50Hz). BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing at any time, ensure that a plug of identical specification is used.
ASSEMBLY AND PREPARATION The machine is supplied fully assembled except as detailed below. Fig.1 Attach the cable and hose storage brackets by sliding them into place on either side of the handle assembly, as shown in Fig.1. Model ELS145 &145R The lance is in two sections, the high pressure hose being integral with the lance handle and trigger assembly. Fig.2 Assemble by slotting the spigot end of the lance into the handle assembly. Push in firmly and twist to lock it in position as shown in Fig. 2. Fig.
ALL Models The low pressure water inlet, shown in Fig. 3, carries a 3/4” BSP thread. A 3/4” BSP adapter with a 1/2” hose connector is provided, so that a suitable hose (not supplied), may be attached. You may use a either a worm drive clip (not supplied), or a snap-on type connector, commonly available from most hardware or DIY stores, to attach the hose, the other end of which should be connected to your water supply. We recommend that you connect to a supply of CLEAN WATER ONLY.
2. Hold the trigger in that position whilst switching the pump ON, and allow the pump to run for a few moments to develop full pressure 3. You may release the trigger once full pressure is developed. In doing so the pump will stop, and will start again as soon as the trigger is pressed once more. NOTE: For the reasons given above, it is recommended that you ALWAYS set the jet to its LOW PRESSURE setting before switching ON.
CAUTION Ensure the operator is aware that when the trigger is pulled, water at high pressure can cause the lance to kick - it should therefore be held firmly. In addition, care must be taken to ensure that the nozzle is NOT aimed at an area where the water jet will cause damage, i.e. away from people, animals, windows - greenhouses etc., and be aware that splash back could also cause damage if the jet is trained on a nearby wall etc.
MAINTENANCE WARNING: Ensure the plug is removed from the socket before carrying out any adjustment, servicing or maintenance. AFTER EACH USE When using chemical detergents, always ensure the system is thoroughly flushed out after use as described above. Ensure the hoses and power cable are coiled and properly stowed. DO NOT allow them to be left casually, in a heap. This invites damage and will cause rapid deterioration. Fig.
TROUBLE SHOOTING FAULT Pressure drop Pressure fluctuations or pressure drop CAUSE REMEDY 1. Air in system 1. Bleed system by quickly operating trigger several times. If necessary operate the machine briefly without the high pressure hose connected. 2. Worn high pressure nozzle. 2. Renew nozzle 3. Pressure regulator incorrectly set 3. Set to required working pressure by turning press. adjuster. (see p8.) 1. No water 1. Turn on water tap 2. Water supply hose too long/too small diameter 2.
PARTS DIAGRAM - ELS145 12
PARTS LIST - ELS145 KIT NO. KIT ITEM DESCRIPTION QTY PART NO.
PUMP AND MOTOR PARTS - ELS145 14
PUMP AND MOTOR PARTS LIST - ELS 145 Please note that parts are available in kit form only KIT Part No. Description Item Nos: A KTRI93402 MANIFOLD KIT 8-32, 34, 35, 37-45,48 & 65 B KTRI93582 CONTROL BOARD KIT 75,76, 82-84, 94, 97-106, 118, & 119 C KTRI93404 CONTROL BOARD KIT 72, 73, 79-81, 90-93, 95, 107, 109 QUICK SOCKET KIT 46, 47 D KTRI82810 E KTRI82808 SMALL VALVE KIT 3-7, 50 F KTRI93991 HEAD KIT 1, 2, 49, 61 G KTRI93406 INTAKE CONNECT.
PARTS DIAGRAM - ELS145R - 160R 16
PARTS LIST - ELS145R - 160R KIT NO: KTRI93635 KTRI93502 KTRI93503 KTRI93504 KTRI93505 KTRI93506 KTRI93526 KTRI93623 KTRI93509 KTRI93524 KTRI93525 KTRI93522 KTRI93527 KIT ITEM A B B C C C C D D E E F F F G G H I I I L N N N N N O O O O O O O O O O P P P P 3 3 4 4 6 7 12 30 32 1 2 6 8 9 10 11 13 30 5 6 29 30 31 37 37 24 25 26 27 28 15 16 17 18 19 6 6 20 21 22 23 33 34 35 36 39 39 14 38 DESCRIPTION Screw Screw (ELS145R) Washer Screw (ELS145R) Screw Screw Clamp Screw Screw Front Cove Lower Front Cove
PUMP AND MOTOR PARTS - ELS145R & ELS160R 18
PUMP AND MOTOR PARTS LIST - ELS145R & 160R Please note that parts are available in kit form only ELS45R Kit Part No.
ELS145 LANCE ELS145R & 160R LANCE PARTS LIST Item Description Part No. 1 Frame FPELS14001 2 3 Cover ON/OFF switch box compl. FPELS14002 FPELS14003 4 4 Motor w/Pump Assy. (ELS145) Motor w/Pump Assy. (ELS160R) FPELS14004 FPELS15004 5 6 Hydraulic cut out High Press. Hose w/Gun assy. (ELS145) FPELS14005 FPELS14006 6 6 High Press. Hose w/Gun assy. 10M (ELS145R/160R) High Press. Hose w/Gun assy.
ACCESSORIES A range of accessories designed for use with your washer are available from your CLARKE dealer, as follows: ELS145/145R Part No. Rotary Brush ........................................................ 7310010 Turbo Nozzle ....................................................... 7310000 Car Brush ............................................................. 7310020 Water Sandblaster ............................................. 7310015 Drain Cleaner ...............................................
