WARNING: Read these instructions before using the machine ELECTRIC TILE CUTTER MODEL NO: ETC8 PART NO: 3400515 OPERATION & MAINTENANCE INSTRUCTIONS LS0711
INTRODUCTION Thank you for purchasing this Electric Tile Cutter. Please read this manual thoroughly, before attempting to operate, and carefully follow all instructions given. It is vitally important that ALL precautions are taken, as specified, which will not only provide protection for yourself and that of others around you, but will also ensure that the product will give you long and satisfactory service.
SAFETY PRECAUTIONS WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/ OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED BELOW REFERS TO YOUR ELECTRIC TILE CUTTER. WORK AREA 1. Keep work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
5. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate which it was designed. 2. Do not use the power tool if the switch does not turn it on and off.
ADDITIONAL SAFETY RULES FOR YOUR TILE CUTTER 1. Remove the mains plug from socket before carrying out any adjustment or servicing. 2. If the supply cord is damaged have it replaced by a qualified person. 3. Always wear both eye and ear protection when using the machine. 4. Ensure that the directional arrow marked on the disc corresponds with the rotational direction of the motor. 5. With the machine disconnected from the power supply, rotate the disc by hand to ensure it is free from obstruction. 6.
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
ASSEMBLY WARNING: BEFORE USING YOUR TILE CUTTER BE SURE TO READ THE INSTRUCTION MANUAL CAREFULLY. FITTING THE BLADE GUARD 1. Loosen the two table securing knobs (Front and rear of the unit). 2. Tilt the table. 3. Slide the blade guard into position as shown and secure using the blade guard locking screws. • The guard is held in position between the frame and a small bracket beneath. FITTING THE BLADE 1. Remove the disc cover by loosening the two screws shown. 2. Loosen and remove the disc fixing nut.
OPERATION WARNING: BEFORE USING YOUR TILE CUTTER BE SURE TO READ THE INSTRUCTION MANUAL CAREFULLY. THE WATER Position the tray as shown and fill 3/4 full with water. • Do not add chemicals or detergents to the water. • Always maintain this level (3/4 full) to ensure that there is sufficient water in the tray for dust suppression and cooling. FITTING THE PARALLEL GUIDE 1. Position the parallel guide on the work table as shown. 2.
STARTING AND STOPPING Press the ON Button (marked “I“) to start the tile cutter. • Allow the tile cutter to reach full speed before cutting any tiles. Press the OFF Button (marked “O“) to stop the tile cutter. NOTE: The disc will continue to rotate for some time after switching off. MAKING A STRAIGHT CUT Position the tile firmly against the parallel guide and push the tile slowly past the disc. • Do not try to force the tile past the disc too quickly.
CLEANING AND MAINTENANCE WARNING: BEFORE STARTING ANY CLEANING OR MAINTENANCE PROCEDURES, DISCONNECT THE PLUG FROM MAINS SUPPLY. CHANGING THE CUTTING DISC • Replacement discs are available from your Clarke dealer. • Only use discs with a diameter of 180 mm. • The replacement discs speed rating must meet or exceed the RPM rating of the tile cutter. 1. Remove the water tray. 2. Remove the disc cover by loosening the two screws shown. 3. Loosen and remove the disc fixing nut. Using the two spanners supplied.
DECLARATION OF CONFORMITY 11 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
