Technical data

ManualsBrandsClarke ManualsAir CompressorPIONEER 220

Flints, Queens Row, London, SE17 2PX T: 020 7703 9786 F: 020 7708 4189 www.flints.co.uk

SECTION 1

1.67

COMPRESSORS

Fini Pioneer 265M This Fini

compressor with a 2 hp motor delivers 7.6

cfm [15 m

/h] making it ideal for the

freelance scenic artist needing a

compressor which is easy to transport in

the boot of a car. It takes a 9 mm

SATA-type hose which will push-fit direct

to the compressor’s connector. If you

need to use 8 mm bore hoses see the

Pioneer Convertor on page 1.68.

Air Receiver: 9.5 L. Maximum Working Pressure: 10 Bar

[145 psi]. 230 V, 8 A. Dims [LWH]: 395 x 320 x 630 mm.

dB[A] 76. Wt: 22 kg.

o Supplied with a panel that protects a pressure switch

and pressure regulator, including pressure gauge and universal quick

coupler for 9 mm hoses.

Fini Pioneer Compressor 265M code list price

FIN265M n/a £269.00

9 mm bor

e hose [10 m] SATAMIM1030 £82.40 £77.74

Fini Big Pioneer Fitted with a

powerful 3 hp 230 V motor delivering 10

cfm [17 m

/h]. The large 20 L receiving

tank is suited for small workshops or for

paint frame use. This compressor is still

very compact and portable although it is

a bit of a heavy lift to get into a car. A 9

mm SATA-type hose will push fit directly

to the compressor’s connector. If you

need to use 8 mm bore hoses see the

Pioneer Convertor [page 1.68].

Air Receiver: 20 L. Maximum Working Pressure: 10 Bar

[145 psi], controlled by a fully automatic pressure switch. 230/240 V, 9.5 A. Dims [LWH]: 470

x 490 x 720 mm. dB [A] 80, Wt: 33.5 kg.

o Supplied with a pressure switch, a

safety valve, drain valve, pressure regulator, including pressure gauge

and universal quick-coupler for 9 mm hoses.

Big Pioneer Compressor 312M code list price

FIN312MB n/a £390.00

9 mm bor

e hose [10 m] SATAMIM1030 £82.40 £77.74

Clarke Raider 15/500 A

powerful British-made portable V-twin

compressor delivering 14.5 cfm with a 50

L tank. Ideal for use with air tools and most

spray equipment. Supplied with a moulded

13 A 3-pin plug to BS1363/A. Fuse rating: 13

A. 230 V single-phase 3 hp motor.

Maximum working pressure: 8 bar. Weight:

42 kg. Fitted with regulator and gauge. For oil see .

NOTE 3 hp motors can run on a 13 A plug so long as they are not run on an extension lead.

Clarke Raider 15/500 code list price

15/500 TOLPED15500 £344.95 £239.36

Clarke Shhh...Air An ultra quiet

compressor emitting just 40 db at 1 m.

Suitable for powering the SATAjet 20 B and

SATAgraph airbrushes. Output 2.15 cfm with

a 9 litre receiver. 8 bar [115psi] maximum

working pressure. 240V. These compressors

have a 50% duty cycle and are suited to the

studio or model shop but not heavy duty use.

For oil see .

Clarke Shhh...Air 3/9 code list price

Shhh...Air 3/9 TOL803 £529.40 £395.00

Compressor Oil Treat

them to some TLC. They do

need oil! You’d be surprised

how many compressors we find

with empty sumps. We

recommend oil “a” for the Fini Pioneer compressor and oil

“b” for the Clarke Pioneer and Raider compressors. The

Shhh...Air compressor uses synthetic oil.

Compressor Oil code 1 L code 5 L

For Pioneer 265/Big Pioneer FIN6

102250000 £9.33 — —

For Raider & Pioneer 220 CLA3050810 £7.95 CLA3050802 £21.37

For Shhh....Air CLA3050795 £12.95 — —

Compressors

The compressors that Flints stocks are mainly used by scenic artists to

power their spray guns or by technicians requiring air for nailers and

staple guns. Most of the ones we list are easily portable so that they can

be lifted into the boot of a car for work in a variety of locations.

Consideration should be given to the air output from the compressor.

Almost any compressor will achieve the pressure needed but it is the

volume of air which is important. The popular SATAJet 1000 B RP spray

gun will use around 7.1 cfm at full tilt whereas the SATAminijet 3000 B

HVLP uses around 4 cfm. As scenic work normally involves stop/start

spraying they will operate satisfactorily from small portable compressors

giving upwards of 7 cfm. Be careful though, because some HVLP guns use

large quantities of air [the SATAjet 4000 HVLP uses 15.2 cfm] and really

require large fixed-installation compressors [please phone for details of

larger units]. Flints has spent a lot of time looking at the compressor

market and has not found it possible to source a truly rugged unit that

can still be easily transported in the boot of a car. The compressors we

list will not withstand continuous use at full pelt. They should, however,

provide reasonable service for the freelance painter for two or three years

so long as they are treated with a little care and given some oil from time

to time. Choose a unit with some spare capacity to ensure a good service

life and please spare a moment to read the instructions!

PIONEER RANGE

Best-

Seller.

OTHER COMPRESSORS

COMPRESSOR OIL

Tradeline

Summary of content (7 pages)

PAGE 1
COMPRESSORS OTHER COMPRESSORS Compressors code list TOLPED15500 £344.95 Tradeline price £239.36 Clarke Shhh...Air An ultra quiet compressor emitting just 40 db at 1 m. Suitable for powering the SATAjet 20 B and SATAgraph airbrushes. Output 2.15 cfm with a 9 litre receiver. 8 bar [115psi] maximum working pressure. 240V. These compressors have a 50% duty cycle and are suited to the studio or model shop but not heavy duty use. For oil see .
PAGE 2
AIR HOSES AND FITTINGS 8 mm BORE HOSES 1/4” BSP THREADS SECTION 1 9 mm BORE HOSES [FOR SATA] 1/4” BSP THREADS The wide bore and special design of the quick release fittings will allow a far greater air flow to the gun. In a simple experiment using a conventional 8 mm hose and one of these 9 mm hoses connected to a “Y” fitting it was found that the 9 mm hose delivered almost twice the volume of air.
PAGE 3
SATA SPRAY EQUIPMENT HVLP and RP? SATAjet 4000 B & SATAjet 4000 B DIGITAL Choose this for the ultimate finish. SATAjet 4000 B RP The SATAjet 4000 B is setting the standards. Featuring state-of-the-art technology, this spray gun has been optimised with the passion for precision so typical of SATA, as well as undergoing intensive practical tests. The result: a soft spray pattern which is second to none, perfect ergonomics and outstanding atomisation for excellent finishes.
PAGE 4
SECTION 1 SATAjet 100 B F RP SATAminijet 4400 B RP PVC SPRAY GUN SATAjet 100 B F RP This is a really excellent reduced-pressure gun at a fantastic price. When operated at around 0.5 bar with the material flow set to high it produces an excellent large splatter effect. These effects need lots of paint so please ensure your paint is diluted enough to flow really freely and make sure the breather in the air cap is clear to avoid Great any suction.
PAGE 5
SATAgraph 3 SATAgraph 3 An airbrush suited for SATA 1 L Alloy Cup Quick change cup for any SATA gun with or without QCC. 1 L Alloy Cup code SATA96685 price £50.00 SATA Cleaning Set Complete with 2 cleaning brushes and 12 SATAgraph 3 SATAgraph 3 without hose 3 m PVC hose and fittings code list SATA134569 £253.00 SATA32987 Tradeline price £227.93 £40.40 cleaning needles. Cleaning Set code SATA64030 price £29.
PAGE 6
OTHER SPRAY EQUIPMENT SECTION 1 PRESSURE POTS & AGITATORS My favourite toy. SATA BVD Pressurised Cup Add Pro Spray Gun An economical and serviceable this cup to your SATA gun to enable it to spray viscous materials. It easily copes with Rosco Crystalgel and Weave Filler. It is ideal for large splatter effects using viscous paints on vertical surfaces when diluted paint would tend to run. Use it to apply texture to built pieces. For large jobs see the 24 L pot below.
PAGE 7
HAND SPRAYERS AIRLESS SPRAY EQUIPMENT Airless Spray Equipment Spray paint & textures fast! Kingfisher Hand-held Mister Strong hand sprayers with a wide range of applications such as applying flameproofing. We stock the popular and economical Kingfisher 2 pint version and the extra robust Hozelock Spraymist Sprayer. code SAFS4000 SAFHOZ4122 price £4.25 £20.