Owner’s Operating Manual CONTINUOUS POWER SYSTEM DIGITAL TECHNOLOGY CT SERIES Models Covered: CT1000R CT1250R CT1500R CT2000R CT2400R CLARY CORPORATION 150 E. Huntington Dr. Monrovia, California 91016 Telephone 626-359-4486 800-44 CLARY Fax. 626-305-0254 World Wide Web HTTP: // WWW.CLARY.COM E-Mail SALES @ CLARY.
THE CONTINUOUS POWER COMPANY TABLE OF CONTENTS TITLE PAGE NO.
THE CONTINUOUS POWER COMPANY INTRODUCTION C ongratulations! You have selected the highest quality protection for your continuous power needs. This unit offers a quiet and compact package with superior performance you can depend on. You now own a CT Series Continuous Power System (CPS) which is an all Digital Technology product manufactured by Clary Corporation, the first name in uninterruptible power system (UPS) reliability.
THE CONTINUOUS POWER COMPANY TECHNICAL DESCRIPTION T Reference the block diagram, on the following page, for a simplified explanation of the system’s operation. The AC utility source is connected to the power and micro-electronics when the input switch is closed. The input line is filtered, power factor corrected and rectified for enhanced performance without disturbing other equipment that may share the same utility circuit.
THE CONTINUOUS POWER COMPANY DB-9F CONTACTS UTILITY INPUT DB-9F RS232 VOLTAGE SELECTOR SWITCH INPUT TRANSFORMER MICROPROCESSOR CONTROLLER COMMON MODE CHOKE VOLTAGE WINDOW DETECTOR POWER FACTOR CORRECTOR RECTIFIER EMERGENCY CUTOFF SWITCH + DC RAILS AC INVERTER GENERATOR STANDBY BATTERY CHARGER AUTO-SELECT OPTION BYPASS LINE FIGURE 1: CT SERIES BLOCK DIAGRAM COMMON MODE CHOKE LOAD
THE CONTINUOUS POWER COMPANY PACKAGING Y our CPS has been carefully packaged to withstand most abuse sustained during shipment. The packing material has been specifically designed to protect this system for normal handling, using most shipping carriers. If there is significant damage to the carton, or if there is any physical damage to this unit, report this to your carrier.
THE CONTINUOUS POWER COMPANY PHYSICAL DESCRIPTION T his section will point out and illustrate the various indicators, functions and controls of the CT Series UPS. Pictured is the front view of the system, then followed by the rear view. The important attributes of the CT Series unit are numbered to assist you in locating them on your machine and also to fully explain its function and how it relates to system operation.
THE CONTINUOUS POWER COMPANY 22 23 18 24 20 19 LOAD II UNSWITCHED AIR EXHAUST, COOLING 25 17 21 16 RACKMOUNT REAR PANEL VIEW 16 17 18 19 20 INPUT - AC Line power inlet 21 SIGNAL - Open-collector signal contacts DC INPUT - Auxiliary battery connector 22 RS232 - RS232 communications signals 120VAC OUTPUT (LOAD 1)- System output, 23 OPTIONAL-SNMP PORT left row 24 VOLTAGE SELECTOR SWITCH 120VAC OUTPUT (LOAD 2)- System output, 25 SYSTEM GROUNDING STUD center row 120VAC OUTPUT (UNSWITCHED)- System outp
THE CONTINUOUS POWER COMPANY enabled during abnormal conditions by pressing and holding the switch again. Alarm - This is a fault indicator that will light in the event that the inverter generator is non-operable. This could be due to an overtemperature situation or an inverter malfunction. Battery Level - This is the battery status bar graph. During normal operation, this bar graph will show the charging of the battery; all indicators lit will represent a fully charged battery.
THE CONTINUOUS POWER COMPANY INSTALLATION I f the unit is to be stored, it is recommended to refresh the internal battery at least once every 90 days. To do this, plug the system in, position the Power On/Off Switch to "ON" and allow the unit to idle for at least 24 hours. The CT unit is designed for installation in a protected environment. These units may be installed in a 19" rack system.
THE CONTINUOUS POWER COMPANY OPERATION O nce the system has been properly installed, it is ready to operate. The following procedures will explain how to start-up the system while plugged into rated electrical power and also how to start-up with no AC power available. Normal Operation on AC Start-Up: • Verify that the unit is plugged into properly rated electrical power. • Position the System Power Switch to the ON position.
THE CONTINUOUS POWER COMPANY SIGNALS AND INTERFACING t the rear of the unit are two DB-9 subminiature, female connectors. These are provided for communications links to a computer or sophisticated monitoring device. SIGNAL provides open collector type contact closures that typically signal Utility Interrupt and Low Battery conditions. A system shutdown feature is also available on this port. Applying a closure across the appropriate pins will cause the system to shutdown in A battery mode.
THE CONTINUOUS POWER COMPANY Page 13
THE CONTINUOUS POWER COMPANY SPECIFICATIONS ELECTRICAL DESIGN Input Standard Features Power Factor Corrected, Digital Regenerative™ On-Line, Sinewave Inverter Powers Load Continuously Extended Brownout Protection Designed for Non-linear Loads Continuous Operation on -20%,+12% Line Automatic Bypass RS232 Data Interface Software Selectable Output Frequency AC Output Switch Auxiliary Battery Connector Rear Mounted Ground Stud Optional SNMP Interface UL Design FCC Class A IEEE 587/ANSI C62.
THE CONTINUOUS POWER COMPANY MODEL SELECTION GUIDE MODEL NUMBER DESCRIPTION CT1000 CT1250 CT1500 CT2000 CT2400 Nominal VA (Max Watts) Input Current Amps (@120VAC) Output Current Amps Input Plug (Standard) 1000 (700) 1250 (875) 1500 (1050) 2000 (1400) 2400 (1680) 7.2 8.8 10.7 14.3 17.4 8.3 10.4 12.5 16.
THE CONTINUOUS POWER COMPANY CARE AND MAINTENANCE T his device is designed to be maintenance-free. It can be cleaned with a damp cloth or nonabrasive cleanser. WARNING: Do not use ACETONE-BASE cleaning solutions. Keep cleaning solutions out of the electrical receptacles on this device. Be sure filters, vents and fans are kept free from accumulation of dust, dirt or lint.
THE CONTINUOUS POWER COMPANY SERVICE AND REPAIR Y our CT Series CPS is backed by one of the finest customer service teams available. Write or call them at any time to obtain more information about your unit. Clary Corporation 150 E. Huntington Dr. Monrovia, CA 91016 1-800-551-6111 If a problem should occur, it is important that you obtain a Return Material Authorization (RMA) number from the Service Department to process any unit returned to the factory.
THE CONTINUOUS POWER COMPANY CLARY CORPORATION LIMITED WARRANTY STANDARD DT/CT/GT 800 - 2000VA and E3000 MODELS DEPOT REPAIR 1. TIME AND SCOPE OF WARRANTY: 1.1 Clary Corporation, (hereafter referred to as Clary) hereby warrants part shipped under this agreement to be free from defective workmanship for a period as stated below, following the date of shipment /accidental damage, misuse or normal wear shall not be construed as a defect.