Instruction manual
86 Concerto — Instruction Manual
Section 2 — Installation
In BNC connector on the backplane in slot 3. And a third cable is looped
from the
Mon Out BNC connector on the backplane in slot 3 to the Mon In BNC
connector on the backplane in slot 4. A cable is then attached to the
Mon Out
BNC connector on backplane 4 and a monitoring device. For more informa-
tion on configured matrix sizes a see Digital Video Monitor Configuration on
page 55.
Figure 51. Digital Video External Cabling
Concerto
EXT COM
2
EXT COM
1
E-NET
2
E-NET
1
AES REF VID-REF 2 VID-REF 1
25 21 17 13 9 5 1
22 18 14 10 6 2
26 23 19 15 11 7 3
28
27
30
2931
32 24 20 16 12 8 4
31 27 23 19 15 11 7
28 24 20 16 12 8
32 29 25 21 17 13 9
30 26 22 18 14 10
5
6
3
4
1
2
INPUTS OUTPUTS
EXP
IN
EXP
OUT
AUDIO/DATA
TDM
MON IN MON OUT
12
12
25 21 17 13 9 5 1
22 18 14 10 6 2
26 23 19 15 11 7 3
28
27
30
2931
32 24 20 16 12 8 4
31 27 23 19 15 11 7
28 24 20 16 12 8
32 29 25 21 17 13 9
30 26 22 18 14 10
5
6
3
4
1
2
INPUTS OUTPUTS
EXP
IN
EXP
OUT
AUDIO/DATA
TDM
MON IN MON OUT
12
12
400W; 11.1A36-60V
+-
AC PWR 1 AC PWR 2
500W; 5A50/60Hz100-240V
ALARM
8138_04_155r0
25 21 17 13 9 5 1
22 18 14 10 6 2
26 23 19 15 11 7 3
28
27
30
2931
32 24 20 16 12 8 4
31 27 23 19 15 11 7
28 24 20 16 12 8
32 29 25 21 17 13 9
30 26 22 18 14 10
5
6
3
4
1
2
INPUTS
OUTPUTS
MON IN MON OUT
HD BACKPLANE
25 21 17 13 9 5 1
22 18 14 10 6 2
26 23 19 15 11 7 3
28
27
30
2931
32 24 20 16 12 8 4
31 27 23 19 15 11 7
28 24 20 16 12 8
32 29 25 21 17 13 9
30 26 22 18 14 10
5
6
3
4
1
2
INPUTS
OUTPUTS
MON IN MON OUT
HD BACKPLANE
MON IN MON OUT
MON IN MON OUT
MON IN MON OUT
MON IN MON OUT
Slot 1, Outputs 1-32,
Cable Mon Out to Mon In
in Slot 2
Slot 2, Outputs 1-64,
Cable Mon Out to Mon In
in Slot 3
Slot 3, Outputs 1-96,
Cable Mon Out to Mon In
in Slot 4
Slot 4, Outputs 1-128
Slot 4, Outputs 1-128,
Cable Mon Out
to Monitoring Device
Audio Monitoring
Analog and AES Digital modules can be combined in the same configured
matrix, and they use internal bussing to support monitor functions, so all
outputs in the matrix are available.
Monitor In connections are not used. One
Destination signal is available to all the
Monitor Out connectors in the config-
ured matrix. All the backplanes have at least one
Monitor Out connector. Two
of the AES Audio backplanes have two
Monitor Out connectors. On the AES
Terminal Block backplane there is a terminal block
Monitor Out connector and
a BNC
Monitor Out connector and on the AES 50 pin D backplane there is a 9
pin D
Monitor Out connector and a BNC Monitor Out connector. See Table 37 on
page 78 for the 9 pin D connector pinouts used on the 50 pin D backplanes.
See Figure 46 on page 80 for the terminal block connector pinout
s used on
the terminal block backplanes. For more
information on configured matrix
sizes and number of Mon Out connectors per matrix see Audio Monitor Con-
figuration on
page 56.