Operator`s manual

11
OPERATION
!
WARNING
ENGINE STARTING PROCEDURES
NOTICE: There are two locations on this engine that require
oil, both the crankcase and the transmission (gearbox). Run-
ning the engine or gearbox with a low oil level can cause
engine damage. Refer to the engine manual for complete
engine information and recommendations.
Engine Oil Level Check
1. BEFORE CHECKING ENGINE:
• make certain the engine is level
• the engine switch is in the OFF position
• the sod cutter blade is NOT engaged
• the drive wheels are disengaged.
2. Remove the ller cap/dipstick and wipe it clean.
3. Insert and remove the dipstick without screwing it into
the ller neck. Check the oil level shown on the dipstick.
4. If the oil level is low, ll to the edge of the oil ller hole
with the recommended oil. SAE 10W-30 is recommend-
ed for general use. Refer to engine oil recommendations
in engine manual for other viscosities and information.
5. Screw in the ller cap/dipstick securely.
Transmission Oil Level Check
1. Check the transmission oil level with the engine stopped
and in a level position.
2. Remove the ller cap/dipstick and wipe it clean.
3. Insert and remove the dipstick without screwing it into
the ller hole. Check the oil level shown on the dipstick.
4. If the oil level is low, add oil to reach the upper limit mark
on the dipstick. Use the same oil that is recommended
for the engine, SAE 10W-30.
5. Screw in the ller cap/dipstick securely.
When replacement parts are
required, use genuine Schil-
ler Grounds Care, Inc. parts or
parts with equivalent character-
istics, including type, strength
and material. Failure to do so
may result in product malfunc-
tion and possible injury to the
operator and/or bystanders.
Carbon monoxide present in the
exhaust is an odorless and deadly gas. Never start or run the
engine inside where exhaust fumes can collect.
Provide enough fresh air to keep fumes from getting too
strong. Replace any warning decal that becomes illegible im-
mediately.
Starting Engine
1. Turn fuel cock to the “open” position.
2. Turn choke on (closed).
3. Turn ignition switch to “on”.
4. Move throttle lever on engine to half throttle position.
5. Pull recoil starter rope until engine starts.
6. After engine is warm, turn off choke (open).
7. Allow engine to run one minute before cutting sod.
8. Check engine rpm setting before operating. DO NOT
exceed 3600 rpm.
Stopping Engine
1. Turn throttle to “slow” position.
2. Turn off ignition switch.
OPERATING THE SOD CUTTER
Preparation
1. Police lawn area for obstacles and debris (i.e. sprin-
klers, hoses, toys, etc.). Remove all items.
2. Make sure underground sprinkler heads and other hid-
den obstacles are marked to prevent damage.
3. Mark other areas where sod cutting will be a problem
or too risky (i.e. mud, tree roots, steep hills).
Operating
1. Start the engine. CAUTION: To avoid injury, do not
place your feet or other body parts under the blade
while starting the engine.
2. Select the correct cutting depth desired up to 2 1/2 inch-
es. Loosen the tee handle from the depth gauge plate,
located under the height adjustment bar, (#3 on illustra-
tion) and put it to the correct height setting. Tighten the
tee handle.
3. Push the wheel drive transport handle (#5 on illustra-
tion) and the cutter blade speed handle (#4 on illustra-
tion) to the desired speed, toward the engine.
4. Raise the main handle upward so the front nose of the
sod cutter rests on the ground.
5. Loosen the 1/2” handle nut (#2 on illustration) and lower
the height adjustment bar to rest on the depth gauge.
Now tighten the 1/2” handle nut securely so it will not
loosen with the vibration of the machine.
6. Go to the back of the machine and lower the handle
until the cutting blade rests on the ground. You are now
ready to cut sod.
7. Turn the throttle to the desired operating speed by pull-
ing the nger throttle control (#6 on illustration) toward
you. Maximum engine rpm is recommended for smooth
operation.