INSTRUCTION MANUAL ENCLOSED MANUEL D’INSTRUCTION À L’INTÉRIEUR MANUAL DE INSTRUCCIONES ADJUNTO STOP ATTENTION STOP IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL OR CALL CUSTOMER SERVICE BEFORE YOU RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED. For Customer Service: www.twinstarhome.
BUILT IN ELECTRIC FIREPLACE INSTALLATION GUIDE MODEL NUMBERS: 39EB500ARA 39EB500GRA 39EB500GRS CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE INSTALLING THIS APPLIANCE WARNING IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED, AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
LISTINGS AND CODE APPROVALS THE BUILDERS BOX SERIES HAS BEEN TESTED AND APPROVED IN ACCORDANCE WITH THE CSA, No.220391, STANDARDS FOR FIXED AND LOCATION DEDICATED ELECTRIC ROOM HEATERS. MODEL SPECIFICATIONS Model Number Description Voltage Watts Remote Control Amps 39EB500ARA 39”Electric Box without any doors 120/208/240 1440/2100/2800 YES 12/10.1/11.7 39EB500GRA 39”Electric Box with glass front 120/208/240 1440/2100/2800 YES 12/10.1/11.
Section 1: Framing Four mounting flanges on the sides of the unit are provided to facilitate installation. Insulation and vapor barrier should be placed a minimum of 2 inches from the unit. This fireplace is a zero clearance design. No combustibles can be placed on the top surface of the fireplace. Combustibles may be installed to the edge of the unit. A 16.0” B 37.0” C 32” D 32.4” E F 38.9” 27.0” G 36.0” H 22.0” I J 28.0” K 15.6” 55.0” L 38.9” M 38.
39EB500GRA Single Glass Door Open The 39EB500GRA with the glass front has concealed latches, to open the glass front follow these steps: 1) There are 2 concealed latches; facing the fireplace the latches are on the upper right and lower right corner of the glass. The latch positions are illustrated in Figure A. 2) In the gap between the glass frame and the larger fireplace frame there is a small tab that needs to be moved to open the glass front.
Section 3: Voltage Selector Switch Location Important: Ensure that the incoming power supply voltage matches the setting of the voltage selector switch!!!!!! Caution: When changing the voltage selector switch from 240 volts to 120 volts ensure that the power supply is turned off. 230 volt position. (see figure 2) When wiring the unit for 120 volts the voltage selector switch should be in the 115 volt position.
Section 4: Mounting Flanges There are two mounting flanges located on each side of the fireplace insert. In order to facilitate the transportation, we make the mounting flanges into flat status. Please bend the mounting flanges into 90o using suitable hardware before installation.
Section 5: 120 Volt Installation Instructions Important • The unit is factory configured for 120 volt operation. • All wiring must be completed prior to installing the unit. • Use 2 conductor wire with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit. • Ensure that the voltage selector switch is in the proper position for the required supply voltage prior to connecting the unit to the power supply. 1.
Figure 6: 120V Wire Connection Diagram L1 L2 N G L1 L2 N FIREPLACE -JUNCTION BOX G N - WHITE WIRE N- WHITE WIRE 120 VOLT POWER SUPPLY L2 - RED WIRE L1- BLACK WIRE L1 - BLACK WIRE G- GREEN WIRE G - GREEN WIRE E-8 BREAKER PANEL
Section 7: 240 Volt Installation Instructions Important • The unit is factory configured for 120 volt operation. You must set the voltage selection switch to 240 volts (230 volt is printed on the switch. • All wiring must be completed prior to installing the unit. • Use 3 conductor wire with ground (4 wires total) from the power supply (breaker panel) to the junction box on the unit.
Figure 8: 240V Wire Connection Diagram L1 L2 N G L1 L2 N FIREPLACE -JUNCTION BOX G N - WHITE WIRE N- WHITE WIRE L2 - RED WIRE L2 - RED WIRE L1- BLACK WIRE L1 - BLACK WIRE G- GREEN WIRE G - GREEN WIRE E-10 240 VOLT POWER SUPPLY BREAKER PANEL
TS-0824LIGHT TS-0824LIGHT TS-0824LIGHT TS-0824LIGHT DOWNLIGHT TS-0824LIGHT NTC E-11 TS-0824LIGHT TS-0824LIGHT FLAME LED DISPLAY TS-E25-LOG-D TS-0824LIGHT TS-0824LIGHT PLUG TS-0824LIGHT 115-230v SWITCH TS-39EB-DRIVER TS-0824LIGHT RECEIVER MAIN PCB CONTROL PANEL TS-0824LIGHT TS-0824LIGHT MOTOR BLUE LED POWER SWITCH L1 L2 N GND Section 8: Wiring Schematic: Fireplace Wiring Diagram
FOYER ÉLECTRIQUE ENCASTRÉ GUIDE D’INSTALLATION NUMÉRO DE MODÈLES: 39EB500ARA 39EB500GRA 39EB500GRS RENSEIGNEMENTS SUR LA SÉCURITÉ VEUILLEZ LIRE CE GUIDE AVANT D’INSTALLER L’APPAREIL AVERTISSEMENT NE PAS SUIVRE LES RENSEIGNEMENTS INDIQUÉS DANS CE GUIDE POURRAIT ENTRAÎNER UN CHOC ÉLECTRIQUE, UN INCENDIE, DES BLESSURES OU LE DÉCÈS. NE PAS CONSERVER OU UTILISER D’ESSENCE OU TOUT AUTRE LIQUIDE OU SOURCE DE VAPEURS INFLAMMABLES PRÈS DE CET APPAREIL OU DE TOUT AUTRE APPAREIL DU MÊME TYPE.
LISTES ET HOMOLOGATIONS LA SÉRIE BUILDERS BOX A ÉTÉ TESTÉE ET APPROUVÉE CONFORMÉMENT AUX NORMES 220391 DE LA CSA POUR LES APPAREILS DE CHAUFFAGE AUTONOMES FIXES INTÉRIEURS. SPÉCIFICATIONS DES MODÈLES NUMÉRO DU MODÈLE DESCRIPTION TENSION PUISSANCE NOMINALE EN WATTS TÉLÉCOMMANDE AMPÈRES 39EB500ARA Boîtier Electrique 39” sans portes 120/ 208/ 240 1440/ 2100/ 2800 OUI 12.00/ 10.10/ 11.7 39EB500GRA Boîtier Electrique 39” avec façade en verre 120/ 208/ 240 1440/ 2100/ 2800 OUI 12.00/ 10.10/ 11.
Section 1: Cadre faciliter l’installation du foyer, quatre brides de fixation sont installées sur les côtés du foyer. L’isolant et le pare-vapeur devraient se trouver à une distance minimale de 5 cm (2 po) du foyer. Ce modèle de foyer n’est pas soumis aux normes de dégagement. Ne placez aucun produit combustible sur la surface de celui-ci. Vous pouvez cependant placer des produits combustibles sur la bordure du foyer. Pour A 16.0” B 37.0” C 32” D 32.4” E 27.0” F 38.9” G 36.0” H 22.0” I J 28.
Ouverture du Modèle à une Vitre 39EB500GRA Les loquets du Modèle 39EB500GRA sont inapparents. Pour ouvrir la vitre en verre procédez comme suit: 1) Il y a deux loquets dissimulés; si l’on se positionne face à la cheminée, les verrous se trouvent dans les coins supérieurs et inférieurs droits de la vitre. Les positions de verrouillage sont illustrées dans la Figure A.
Section 3: Emplacement du commutateur de tension Important: Assurez-vous que la tension d’alimentation entrante correspond au réglage du commutateur de tension!!!!!! Mise en garde : Lorsque vous glissez le commutateur de tension de 240 à 120 volts, assurez-vous d’avoir coupé l’alimentation. Le sélecteur de tension est situé derrière le panneau de briques du haut sur la droite. Lors du câblage de cette unité sur 208/240 volts, le sélecteur de tension doit se trouver en position 230 volts. (voir figure 2).
Section 4: Brides de fixation Le foyer comporte une bride de fixation de chaque côté. Pour faciliter le transport, nous aplanissons ces brides. Veuillez plier les brides de fixation à angle de 90º avec de la quincaillerie appropriée avant d’installer le foyer.
Section 5: Instructions pour installation sur circuit 120 volts Important • Ce foyer a été réglé en usine pour fonctionner sous une tension de 120 volts. • Tous les fils doivent avoir été mis en place avant de procéder à l’installation du foyer. • Utilisez 2 fils conducteurs avec un fil de mise à la terre (3 fils au total) entre l’alimentation électrique (panneau de disjoncteurs) et la boîte de connexion se trouvant sur le foyer.
Diagramme de connexion des fils : figure 6 L1 L2 N G L1 L2 N G N - FIL BLANC BOÎTE DE JONCTION DU FOYER N- FIL BLANC ALIMENTATION 120 VOLTS L2 - FIL ROUGE L1- FIL NOIR L1 - FIL NOIR G- FIL VERT G - FIL VERT F-8 PANNEAU DE DISJONCTEURS
Section 7 : Instructions pour installation sur circuit 240 volts Important • Ce foyer a été réglé en usine pour fonctionner sous une tension de 120 volts. Vous devez régler le commutateur de tension à 240 volts (230 volts est indiqué sur le commutateur). • Utilisez 3 fils conducteurs avec un fil de mise à la terre (4 fils au total) entre l’alimentation électrique (panneau de disjoncteurs) et la boîte de connexion se trouvant sur le foyer.
Diagramme de connexion des fils : figure 8 L1 L2 N G L1 L2 N BOÎTE DE JONCTION DU FOYER G N - FIL BLANC N- FIL BLANC L2 - FIL ROUGE L2 - FIL ROUGE L1- FIL NOIR L1 - FIL NOIR G- FIL VERT G - FIL VERT F-10 ALIMENTATION 240 VOLTS PANNEAU DE DISJONCTEURS
TS-0824LIGHT TS-0824LIGHT TS-0824LIGHT DOWNLIGHT TS-0824LIGHT F-11 TS-0824LIGHT NTC TS-0824LIGHT TS-0824LIGHT FLAME LED DISPLAY TS-E25-LOG-D TS-0824LIGHT TS-0824LIGHT PLUG TS-0824LIGHT 115-230v SWITCH TS-39EB-DRIVER TS-0824LIGHT RECEIVER MAIN PCB CONTROL PANEL TS-0824LIGHT TS-0824LIGHT MOTOR BLUE LED POWER SWITCH L1 L2 N GND
CHIMENEA ELÉCTRICA EMPOTRADA GUÍA DE INSTALACIÓN NÚMEROS DE MODELOS: 39EB500ARA 39EB500GRA 39EB500GRS INFORMACIÓN SOBRE SEGURIDAD PARA EL CONSUMIDOR LEA ESTE MANUAL ANTES DE INSTALAR EL APARATO ADVERTENCIA EN CASO DE NO SEGUIR LA INFORMACIÓN EN ESTE MANUAL, PODRÍA OCURRIR UNA DESCARGA ELÉCTRICA O INCENDIO Y, COMO CONSECUENCIA, DAÑOS A LA PROPIEDAD, LESIONES PERSONALES O LA PÉRDIDA DE LA VIDA.
APROBACIONES DE CÓDIGOS Y LISTAS LA SERIE DE CAJA DE LOS FABRICANTES SE HA PROBADO Y APROBADO DE ACUERDO CON LAS NORMAS CSA, Nº 220391 PARA LOS CALENTADORES DE INTERIOR ELÉCTRICOS FIJOS Y ESPECÍFICOS PARA UNA UBICACIÓN. ESPECIFICACIONES DEL MODELO NÚMERO DEL MODELO DESCRIPCIÓN VOLTAJE VATIOS DE POTENCIA NOMINAL CONTROL REMOTE AMPERAJE 39EB500ARA Caja Eléctrica de 39¨ sin ninguna puerta 120/ 208/ 240 1440/ 2100/ 2800 SÍ 12.00/ 10.10/ 11.
Sección 1: Marco Esta chimenea está diseñada sin holgura. No se debe apoyar ningún material combustible sobre la superficie de la chimenea, pero sí se pueden colocar a la orilla de la unidad. A 16.0” B 37.0” C 32” D 32.4” E 27.0” F 38.9” G 36.0” Se proporcionan cuatro bridas a los lados de la unidad para facilitar la instalación. La barrera de aislamiento y vapor se debe ubicar a 2 pulgadas de la unidad, como mínimo. H 22.0” I J 28.0” K 15.6” L 38.9” 55.0” M 38.
39EB500GRA Apertura de la puerta de cristal individual La 39EB500GRA con un cristal frontal tiene pestillos ocultos, para abrir el cristal frontal siga los siguientes pasos: 1. Hay 2 pestillos ocultos; de cara al calentador los pestillos están en la parte superior derecha y la parte inferior derecha del cristal. La posición de los pestillos está ilustrada en la figura A. 2.
Sección 3: Ubicación del interruptor selector de voltaje Importante: Asegúrese de que el voltaje del suministro de energía de entrada coincida con la configuración del interruptor selector de voltaje.!!!!!! Precaución: Cuando cambie el interruptor selector de voltaje de 240 voltios a 120 voltios, cerciórese de que el suministro de energía esté apagado. El botón de selector de voltage está situado detrás del panel de la tapia superior en la esquina derecha.
Sección 4: Bridas de montaje Hay dos bridas de montaje ubicadas a cada lado de la chimenea. A fin de facilitar el traslado, se elaboran bridas de montaje planas. Doble las bridas de montaje 90º con la ayuda de una herramienta adecuada antes de realizar la instalación.
Sección 5: Instrucciones de instalación para 120 voltios Importante • La unidad viene configurada de fábrica para operar con 120 voltios. • Se debe finalizar todo el cableado antes de instalar la unidad. • Utilice un cable de 2 conductores con puesta a tierra (3 cables en total) desde el suministro de energía (panel del interruptor) hasta la caja de conexiones de la unidad.
Diagrama de conexión de cables: Figura 6 L1 L2 N G L1 L2 N G CAJA DE CONEXIONES DE LA CHIMENEA N - CABLE BLANCO N - CABLE BLANCO SUMINISTRO DE ENERGÍA DE 120 VOLTIOS L2 - CABLE ROJO L1- CABLE NEGRO L1 - CABLE NEGRO G- CABLE VERDE G - CABLE VERDE S-8 PANEL DEL INTERRUPTOR
Sección 6: Instrucciones de instalación para 240 voltios Importante • La unidad viene configurada de fábrica para operar con 120 voltios. Debe fijar el interruptor selector de voltaje en 240 voltios (en el interruptor dice 230 voltios). • Utilice un cable de 3 conductores con puesta a tierra (4 cables en total) desde el suministro de energía (panel del interruptor) hasta la caja de conexiones de la unidad. 1.
Diagrama de conexión de cables: Figura 8 L1 L2 N G L1 L2 N CAJA DE CONEXIONES DE LA CHIMENEA G N - CABLE BLANCO N- CABLE BLANCO L2 - CABLE ROJO L2 - CABLE ROJO L1- CABLE NEGRO L1 - CABLE NEGRO G- CABLE VERDE G - CABLE VERDE S-10 SUMINISTRO DE ENERGÍA DE 240 VOLTIOS PANEL DEL INTERRUPTOR
TS-0824LIGHT TS-0824LIGHT TS-0824LIGHT DOWNLIGHT TS-0824LIGHT S-11 TS-0824LIGHT NTC TS-0824LIGHT TS-0824LIGHT FLAME LED DISPLAY TS-E25-LOG-D TS-0824LIGHT TS-0824LIGHT PLUG TS-0824LIGHT 115-230v SWITCH TS-39EB-DRIVER TS-0824LIGHT RECEIVER MAIN PCB CONTROL PANEL TS-0824LIGHT TS-0824LIGHT MOTOR BLUE LED POWER SWITCH L1 L2 N GND
INSTRUCTION MANUAL ENCLOSED MANUEL D’INSTRUCTION À L’INTÉRIEUR MANUAL DE INSTRUCCIONES ADJUNTO STOP ATTENTION STOP IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL OR CALL CUSTOMER SERVICE BEFORE YOU RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED. For Customer Service: www.twinstarhome.