Instructions / Assembly

ManualsBrandsClassic Flame ManualsHeating, Ventilation, and Air ConditioningDrew 26 in. Media Mantel Electric Fireplace in Autumn Birch

Français p. 15

ELECTRIC FIREPLACE MANTEL

26MM9405

INSTRUCTION MANUAL

Requires-Electric Fireplace Requires-Electric Fireplace

Insert with HeaterInsert with Heater

www.twinstarhome.com

In English call: 866-661-1218

In French call: 866-374-9203

In Spanish call: 866-661-1218

ATTENTION

For Customer Service:

Twin-Star International, Inc.

Delray Beach, FL 33445

Made in China

Printed in China

Español p. 8

MAXIMUM LOAD 30 lb. (13.6kg)

CAUTION: This unit is intended for use only with the products and maximum weights

indicated. Use with other products or products heavier than the maximum weights

indicated may result in instability causing possible injury

Note: Flat Panel TVs with base support should be placed squarely in the center of the

stand with no overhang on any side.

FIT UP TO 62” PLASMA/LCD TELEVISIONS

MAXIMUM LOAD 135 lb. (61.22 kg)

Summary of content (7 pages)

PAGE 1
ELECTRIC FIREPLACE MANTEL 26MM9405 INSTRUCTION MANUAL Español p. 8 Français p. 15 FIT UP TO 62” PLASMA/LCD TELEVISIONS MAXIMUM LOAD 135 lb. (61.22 kg) MAXIMUM LOAD 30 lb. (13.6kg) CAUTION: This unit is intended for use only with the products and maximum weights indicated. Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury.
PAGE 2
PACKAGE CONTENTS G II K II F I D C H L I B E H J L A Part A B C D E F G H I J K L Description Hearth/Base Center Left Side Panel Center Right Side Panel Center Front Panel Left Side Panel Right Side Panel Glass Top Glass Shelf Side Back Panel Insert Support Bar Mantel/Top Glass Door 2 Quantity 1 1 1 1 1 1 1 2 1 1 1 2
PAGE 3
HARDWARE CONTENTS Part Description Picture (Shown to size) Quantity AA Bolt 20+1 extra BB Washer 20+1 extra CC Wood Dowel 20+1 extra DD Door Touch Clip 2 EE Suction Cup 6 FF Pivot Hinge 4 GG Magnetic Spring Catch 2 HH Shelf Pin 8 II Metal Support Post 6 JJ Screw 22 KK Screw 8 LL Tipping Restraint Hardware 2 ZZ Touch-up Pen 1 3
PAGE 4
SAFETY INFORMATION WARNING • Before assembly, carefully use scissors or utility knife to cut and unwrap all parts. Make sure you do not discard the hardware. CAUTION • Use care in assembling your new fireplace. Take your time and use the hardware provided and a quality Phillips head screwdriver. Never overtighten bolts. • Do not sit on any part of the mantel. • All panels are labeled left and right as viewed from the front of unit.
PAGE 5
2. Locate Hearth/Base (A) and set out finished side up on the floor. Insert one Wood Dowel (CC) into each of the pre-drilled holes. Attach the Completed assembly from step 1 to the Hearth/Base (A). Make sure that dowels are seated into the pre-drilled holes in the Hearth/Base. Using Bolts (AA) and Washers (BB) attach panels through pre-drilled holes in the mounting blocks. HAND TIGHTEN ONLY. Insert one Wood Dowel (CC) into each of pre-drilled holes.
PAGE 6
5. Attach the Magnetic Spring Catch (GG) on the bottom of Top Panel, tighten screws (KK) through holes to the block as shown in diagram. Place the Door Touch Clip (DD) to the glass door. Insert the Pivot Hinge (FF) into the plastic mat as shown in diagram. Then push the Glass Doors (L) snug to the Pivot Hinges (FF), use a Phillips Head Screwdriver to tighten the pivot hinge against the glass. Fig. 5 DD L WARNING Do not over tighten catch screws.
PAGE 7
8. PLEASE READ ALL “ELECTRIC FIREPLACE INSERT” INSTRUCTIONS PRIOR TO INSTALLING ELECTRIC INSERT IN YOUR COMPLETED FIREPLACE MANTEL. INSTALL THE INSERT IN YOUR FIREPLACE CLOSE TO ITS FINAL POSITION. Lift insert carefully into the back of the unit and center in the insert opening. Do not drag insert across hearth/base as it may scratch the unit. Connect the Insert Support Bar (J) to the inside left and right panels, using the bolt (AA) and washer (BB) through pre-drilled holes.