Installation guide

ManualsBrandsClassicFlame ManualsHome building and Decor36EB110-GRT

Electric Builder Box

E-1

CONSUMER SAFETY INFORMATION

PLEASE READ THIS MANUAL BEFORE USING THIS APPLIANCE

WARNING

Thank you and congratulations on your purchase of a Classic Flame electric

builder box. Please read the installation instructions before installing and

operating this appliance.

IMPORTANT: Read all instructions and warnings carefully before using.

Failure to follow these instructions may result in a possible electric shock,

ﬁre hazard and/ or injury and will void the warranty.

For Customer Service:

E-Mail: parts@twinstarhome.com

In English Call: 866-661-1218

In French Call: 866-374-9203

In Spanish Call: 866-661-1218

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED,

AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE

VAPORS AND LIQUIDS IN THE VICINITY OF THIS

OR ANY OTHER APPLIANCE.

ELECTRIC BUILDERS BOX

MODEL NUMBERS:

INSTALLATION GUIDE

36EB110-GRT, 36EB111-GRC

36EB220-GRT, 36EB221-GRC

Twin-Star International, Inc.

Delray Beach, FL 33445

U.S.A.

Made in China

Printed in China

Summary of content (15 pages)

PAGE 1
ELECTRIC BUILDERS BOX Electric Builder Box INSTALLATION GUIDE MODEL NUMBERS: 36EB110-GRT, 36EB111-GRC 36EB220-GRT, 36EB221-GRC CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE USING THIS APPLIANCE WARNING IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED, AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
PAGE 2
LISTINGS AND CODE APPROVALS THE BUILDERS BOX SERIES HAS BEEN TESTED AND APPROVED IN ACCORDANCE WITH CSA AND UL STANDARDS FOR FIXED AND LOCATION DEDICATED ELECTRIC ROOM HEATERS. MODEL SPECIFICATIONS VOLTAGE MODEL NUMBER DESCRIPTION 36EB110-GRT 36” TRADITIONAL 120 36EB220-GRT 36” TRADITIONAL 208/240 36EB111-GRC 36” CONTEMPORARY 120 36EB221-GRC 36” CONTEMPORARY 208/240 RATED POWER WATTS 1440 2100/2800 1440 2100/2800 BTU AMPS 4400 12 6700/8900 10.1/11.7 4400 12 6700/8900 10.1/11.
PAGE 3
SECTION 1: PREPARATION 1.) Open the master carton, stone box , and wall mounted control box and make sure you have all the parts listed. Remove the parts from the cartons and put them in a safe location ( see figure 1.
PAGE 4
2.) Unscrew 2 screws on the side edge of the frame (Fig. 2). Securely holding the frame lift up and pull away from the unit to remove the frame. Do not remove the protective plastic film at this time. Place the frame in a safe place( see figure 2.
PAGE 5
SECTION 2: FRAMING Section 1: Framing This fireplace is a zero clearance design. No combustibles can be placed on the top surface of the fireplace. Combustibles may be installed to the edge of the unit. Insulation and vapor barrier should be placed a minimum of 2 inches from the unit. Build the framing according to the specifications shown in the below table & figure 3. MODEL 36EB110-GRT 36EB220-GRT 36EB111-GRC 36EB221-GRC A B 8” 35” C 23.8” D 24” E 18” F G H 36” 33.5” 34.7” I J 23.
PAGE 6
SECTION 4: MOUNTING Install Method： 1.) Remove front frame (see figure 2). 2.) Remove the screws holding side panels and then remove the side panels (see figure 4 & 5). 3.) Insert the builders box into the opening in the framing.
PAGE 7
4.) Install the builders box using 4pcs screws from the inside of the builder box (see figure 6 & 7). 5.) Remount the side panels. 6.) Place the stones as desired.(Only for 36EB111-GRC & 36EB221-GRC ) 7.) Remount the front frame. Figure 6: Mounting Tab Location Place sto nes here.
PAGE 8
SECTION 5: 120V WIRING INSTRUCTIONS 1.) Loosen the screw securing the junction box cover and remove the cover. 2.) Pull the power supply wires through the hole in the cover. 3.) Pull out the 4 wires marked L, N, G, S from the junction box on the side of the builder box. 4.) Connect the black L wire from the unit to the black L from the power supply. 5.) Connect the white N wire from the unit to the white N from power supply. 6.
PAGE 9
SECTION 5: 208/240V WIRING INSTRUCTIONS 1.) Loosen the screw securing the junction box cover and remove the cover. 2.) Pull the power supply wires through the hole in the cover. 3.) Pull out the 5 wires marked L1, L2, N, G, S from the junction box on the side of the builder box. 4.) Connect the black L1 wire and red L2 from the unit to the two dedicated 15 amp lines from the power supply. 5.) Connect the white N wire from the unit to the white N from power supply. 6.
PAGE 10
SECTION 6: INSTALL CONTROL BOX 1. Mount the control box bracket to the wall using provided screws. 2. Connect control panel wire to extension cable. 3. Insert the control box to the bracket and finish the control box installation.
PAGE 11
SECTION 6: CHECK & TEST 1.) Recheck that all the wiring works. Check that all connections are tight and correct to the manual. 2.) Switch on the power supply to the unit. 3.) Press the POWER button on the control box. 4.) Using the wall controls test all the functions to ensure they are working correctly. If any functions do not work recheck the wiring using sections 4 and 5 of this guide. 5.) Use the remote control to operate the unit, check all the functions. 6.)Finish wall construction work.
PAGE 12
SECTION 10: WIRING SCHEMATIC 36EB110-GRT E-12
PAGE 13
36EB220-GRT E-13
PAGE 14
36EB111-GRC E-14
PAGE 15
36EB221-GRC E-15