BUILT IN ELECTRIC FIREPLACE USER’S GUIDE MODEL NUMBERS: 33EB304GRS 39EB364GRS CONSUMER SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE USING THIS APPLIANCE WARNING IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED. AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. DO NOT STORE OR USE GASOLINE OR OTHER FLAMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. Thank you and congratulations on your purchase of a Classic Flame fireplace.
SECTION 1: BEGINNING 1) Prior to first use verify that the circuit breakers are on. 3) If your heater does not emit heat, verify the wall thermostat (not included) is set above the current room temperature. If this does not work, switch the main Power Button off for 5 minutes and try again. 2) The heating element on this unit may emit a slight, harmless odor when first used. This odor is a normal reaction to heating the internal heater parts for the first time.
Section 2: Preparing Fireplace for Use Pre-Installation Diagram: Figure 1 REMOTE CONTROL MESH CURTAIN IN PLASTIC BAGS ZIP TIE a smaller bag which contains a box. This box contains the remote control transmitter. 5) Remove the remote control transmitter from the box and install the included batteries. Follow the instructions in the next section to operate the controls of your electric fireplace.
SECTION 3: PRODUCT ORIENTATION Figure 2 LOGS AND EMBERBED CONTROL PANEL MESH CURTAINS GLASS DOORS Some of the following illustrations are shown without the glass doors and mesh curtain. This is only to help the illustrations print more clearly.
SECTION 4: OPERATION CONTROL PANEL FUNCTIONS Figure 3 TO ACCESS CONTROL PANEL- Open the front glass doors, then slide the mesh curtains to the sides. Lift the hinged door that covers the control panel (figure 3). CONTROL PANEL MAIN POWER- The MAIN POWER button supplies power to all of the functions of the fireplace. This button must be in the ON position for any of the functions to work including the remote. HEATER- The Heater button supplies power to the heater and blower.
SECTION 5: SERVICE LIGHT BULBS Figure 6 This electric fireplace uses (3) three clear 120V, 40 watt, E12 socket base light bulbs (open small base, chandelier type) For your convenience, if a bulb burns out, it is a good idea to replace all the bulbs at the same time. These bulbs are available at most home centers, hardware stores or grocery stores. 1) Turn the Main Power button off. 2) If fireplace has been operating, let the unit cool at least 2 hours.
SECTION 6: DOWN LIGHT Figure 9 This fireplace uses 1 clear 120V, 4 watt, E12 socket base bulb (open, small base, night light type). 1) Follow steps 1 through 3 in the above section 2) Locate the down light diffuser on the inside ceiling of the firebox (Figure 9). 3) Remove the screws securing the down light diffuser (Figure 10). There are 2 screws in the 33EB304GRS and 3 screws in the 39EB364GRS.
SECTION 7: MAINTENANCE The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater unit is recommended. The vent in the for the heat output should be cleaned periodically. The area around the controls should also be kept clean. Make sure the unit is turned OFF whenever you are cleaning the heater or fireplace. WARNING: Make sure the power is turned off before proceeding.
1 YEAR LIMITED WARRANTY For Classic Flame™ Electric Fireplace Models BASIC WARRANTY sequential loss or damage arising out of the use, or inability to use the product, except as provided by law. 8. All other warranties – expressed of implied – with respect to the product, its components and accessories, or any obligations/liabilities on the part of the Company are hereby expressly excluded. 9.
FOYER ÉLECTRIQUE ENCASTRÉ GUIDE DE L’UTILISATEUR NUMÉRO DE MODÈLES: 33EB304GRS 39EB364GRS RENSEIGNEMENTS SUR LA SÉCURITÉ VEUILLEZ LIRE CE GUIDE AVANT D’UTILISER L’APPAREIL AVERTISSEMENT NE PAS SUIVRE LES RENSEIGNEMENTS INDIQUÉS DANS CE GUIDE POURRAIT ENTRAÎNER UN CHOC ÉLECTRIQUE, UN INCENDIE, DES BLESSURES OU LE DÉCÈS. NE PAS CONSERVER OU UTILISER D’ESSENCE OU TOUT AUTRE LIQUIDE OU SOURCE DE VAPEURS INFLAMMABLES PRÈS DE CET APPAREIL OU DE TOUT AUTRE APPAREIL DU MÊME TYPE.
SECTION 1: POUR COMMENCER 3) Si l’appareil de chauffage n’émet aucune chaleur, assurez-vous que le thermostat mural (non inclus) est fixé à une température supérieure à la température actuelle de la pièce. Si l’appareil ne fonctionne toujours pas, coupez l’alimentation de l’appareil en appuyant sur le bouton Power (mise en marche) puis rallumez le foyer après 5 minutes.
Section 2: PRÉPARER LE FOYER AVANT DE L’UTILISER Figure 1 TÉLÉCOMMANDE RIDEAUX DE MAILLE DANS DES SACS DE PLASTIQUE ATTACHE 4) Du côté gauche, à l’intérieur du sac contenant les rideaux, se trouve un petit sac contenant une boîte; cette boîte contient la télécommande. 5) Sortez la télécommande de la boîte et installez-y les batteries fournies. Suivez les directives de la section suivante pour savoir comment utiliser votre foyer électrique.
SECTION 3 : ORIENTATION VERS LE PRODUIT Figure 2 BÛCHES ET LIT POUR TISONS PANNEAU DE CONTRÔLE RIDEAUX DE MAILLE PORTES DE VERRE Certaines des illustrations suivantes n’incluent pas les portes de verre et le rideau de mailles. Cela ne vise qu’à favoriser une meilleure impression des illustrations.
SECTION 4: FONCTIONNEMENT FONCTIONS DU PANNEAU DE CONTRÔLE Figure 3 POUR ACCÉDER AU PANNEAU DE CONTRÔLE - Ouvrez les portes de verre à l’avant puis glissez le rideau de mailles sur les côtés. Soulevez la porte avec charnières recouvrant le panneau de contrôle (figure 3). PANNEAU DE CONTRÔLE MAIN POWER - Le commutateur principal alimente toutes les fonctions du foyer.
SECTION 5 : ENTRETIEN AMPOULES Figure 6 Ce foyer électrique utilise trois (3) ampoules claires 120 volts, 40 watts de type E12 (ouverte, petite base, type chandelier). Nous vous conseillons de toujours remplacer toutes les ampoules en même temps lorsque l’une d’elles brûle. Vous trouverez ces ampoules dans la majorité des centres de rénovation, quincailleries ou magasins d’alimentation. 1) Coupez l’alimentation de l’appareil en appuyant sur le bouton d’alimentation principale (« Main Power »).
section 6: PLAFONNIER D’INTENSITÉ Figure 9 Ce foyer utilise une (1) ampoule claire 120 volts, 4 watts de type E12 (ouverte, petite base, type veilleuse). 1) Suivez les étapes 1 à 3 indiquées dans la section ci-dessus. 2) Le diffuseur du plafonnier d’intensité se trouve dans le plafond intérieur du foyer (figure 9). 3) Retirez les vis retenant le diffuseur du plafonnier (figure 10). Il y a 2 vis pour le modèle de foyer 33EB304GRS et 3 vis pour le modèle 39EB364GRS.
SECTION 7: ENTRETIEN Les moteurs utilisés par le ventilateur et la génératrice de flammes sont prélubrifiés pour une durée de vie prolongée et n’exigent aucune autre lubrification. Nous recommandons cependant un nettoyage périodique avec aspirateur pour le ventilateur/élément chauffant. L’orifice de ventilation pour la sortie de chaleur devrait être nettoyé de façon périodique. La zone autour des boutons de commande devrait aussi demeurer propre.
GARANTIE LIMITÉE D’UN AN Pour les modèles de foyer électrique Classic Flame™ GARANTIE DE BASE 7. Le propriétaire/utilisateur assume tous les autres risques, le cas échéant, y compris tout dommage ou perte direct, indirect ou accessoire découlant de l’utilisation ou de l’incapacité à utiliser le produit, sauf comme le prévoit la loi. 8.