ENGLISH ® GLOW UP STRIP 100 & FLIGHT CASE C71080 F21250 INSTRUCTIONS MANUAL CONTENTS Pag.
SAFETY INFORMATION GLOW UP STRIP 100 • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
SAFETY INFORMATION FLIGHT CASE • Installation Ensure that the Flight Case, when used for charging GLOW UP, is positioned at a distance of 15 cm from any surface or wall, to allow proper ventilation. • Maximum ambient temperature Do not operate the device if ambient temperature (Ta) exceeds 40°C. IP20 • IP20 protection rating The fitting is protected against penetration by solid bodies of over 12mm (0.
UNPACKING AND PREPARATION 1 ENGLISH ® STRIP 100 GLOW UP T & FLIGH INSTR UCTIO C71080 CASE IST003/001 AL NS MANU product! CONTEN TS Contents UP n GLOW Page Safety informatio FLIGHT CASE 2 n Safety informatio n 3 and preparatio Unpacking film 4 of the protective Removal 4 and start-up Installation 5 Control panel 6 keys menu Shortcut 8 C” Button function Alone “GLOWUP 8 for Stand Preset colors 9 Main menu 10 Mode Operating 15 - Aerial Manual zoom 16 ce Maintenan s 17 accessorie Optional 19 data Tec
3 2 3 1 3 1 5 4 5 4 Projector installation - Fig. 3 The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall. WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105015/801 available upon request). This must be secured to the projector support structure and then hooked to the fastening point at the centre of the base.
4 1 1 4 3 3 2 2 Connecting and disconnecting the power cord - Fig. 4 When connecting the power cord the user can choose whether to use the GLOW UP in one of the following ways: 1) Power cord connected for battery charge. 2) Power cord connected for projector power (thus bypassing battery operations). The GLOW UP cannot work in both ways simultaneously. CONTROL PANEL 5 Power Supply Connections to the power mains - Fig.
Switching on the projector - Fig. 7 The projector immediately turns on when the power cord is plugged in or, if used in battery mode, by pressing and holding down keys several seconds. Clay Paky GLOW UP STRIP 100 GLOW UP STRIP 100 Software release x.x x Address xxx xxxxx ??? * BAT xx% A and S for * see pag. 7 Display symbology The control panel (Figure 8) has a display and buttons for complete programming and management of the projector menu.
SHORTCUT KEYS MENU A key and UP B, the DMX address setting function can be quickly accessed.
PRESET COLORS FOR STAND ALONE Colour Reference 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 LEE 101 LEE 103 LEE 105 LEE 107 LEE 111 LEE 113 LEE 115 LEE 116 LEE 119 LEE 128 LEE 132 LEE 134 LEE 135 LEE 136 LEE 147 LEE 180 LEE 156 LEE 079 LEE 194 LEE 024 LEE 017 LEE 019 LEE 108 LEE 126 LEE 141 ROSCO 378 ROSCO 358 ROSCO 081 ROSCO 066 ROSCO 030 ROSCO 318 ROSCO 332 ROSCO 034 ROSCO 039 RGBW RED GREEN
MENU SET 1 3 2 Program Edit scene DMX Address Advanced Setup Radio DMX Mode Edit Sequence Lock Option DMX recorder Auto Switch Off option Led Control Led Current Battery Power Power Mode Display Contrast Charging answer Battery Display Fixture ID FW Uploader Appl. Upload Boot.
PROGRAM MENU Program EDIT SCENE To create/overwrite/modify a SCENE customised by the user: 1) Press ENTER – SCENE 1 appears on the display. and DOWN keys to select from the ten available 2) Use the UP SCENES. 3) Press ENTER to open a SCENE. 4) A value can be associated with each GLOW UP channel inside each SCENE using the UP and DOWN keys. 5) When finished with settings, press SELECT . A confirmation message appears: SAVE SCENE X ?.
Advanced Setup DMX MODE Assigns the desired command to the GLOW UP Radio module – current settings appear on the display.
Advanced Setup LED CONTROL It allows you to select the operating mode of the GLOW UP Strip 100 between the two available: 1) Press ENTER – the current setting appears on the display. 2) Use the UP and DOWN keys to select one of the following settings: Common Mode: all LEDS are on simultaneously (page 22) Single Mode: The LEDS are divided into 2 sets of 5 LEDS each (page 23).
Advanced Setup CHARGING ANSWER This allows a default answer can be assigned for the battery charging request, when the GlowUp Strip is powered by the relative power cable (powercon): - On selecting YES, it will automatically switch to the powered by battery status 1 minute after the GlowUp Strip cord is connected to the mains. - On selecting NO, it will automatically switch to the powered by cable status (excluding the battery mode) 1 minute after the GlowUp Strip cord is connected to the mains.
Advanced Informations TOTAL LED HOURS Displays total LED working hours, from construction to today. 1) Press ENTER – total LED working hours appear on the display. 2) Press SELECT to return to the previous Menu. Total LED hours A S SYSTEM VERSION Displays the version of the firmware loaded on the CPU board. 1) Press ENTER – two options appear on the display: Application release Boot release (Backup Software) 2) Use the UP and DOWN keys to select which of the two firmware version items to be displayed.
Advanced Reset FACTORY RESET Resets GLOW UP and automatically sets the Factory Default settings. 1) Press ENTER – a confirmation message appears on the display (OK?) 2) Press ENTER to RESET or SELECT to return to the previous Menu. Default after reset: “Master Output”-> "Cable + Wireless" "Repeater"-> "Disable" "Repeater"-> "Function"->"Repeat & Play" "Repeater"-> "Direction"->"Wirel.
OPERATING MODES NOTE: the Wireless board is not two-way, therefore the following functions are excluded: 1) Repeater from Wireless to Wireless. 2) Receiving and transmitting wireless at the same time.
RDM CONTROLS IMPLEMENTED FOR GLOWUP SERIES Control PID GET SET Description controller side DEVICE_INFO 0x0060 X IDENTIFY_DEVICE 0x1000 DMX_START_ADDRESS 0x00F0 X SOFTWARE_VERSION_LABEL 0x00C0 X Reads the firmware version SUPPORTED_PARAMETERS 0x0050 X Gathers the PIDS on the non-basic controls PARAMETER_DESCRIPTION 0x0051 X Gathers information on the controls related to the manufacturer DMX_PERSONALITY 0x00E0 X DMX_PERSONALITY_DESCRIPTION 0x00E1 X Reads the description of the
MAINTENANCE 9 5 90° 3 4 2 1 Charging GLOW UP - Fig. 9 From 1 to 4 GLOW UPs can be simultaneously charged by appropriately connecting and powering the flight-case. 10 Fuse 6,3x32mm 2.5AT 250Vac (FUS000) 1 Fuse 6,3x32mm 10AT 250Vac (030470) 2 Replacing flight case fuses - Fig. 10 Each flight-case has 2 fuses associated with the main power cord connection and one fuse for each GLOW UP charge station.
11 1 3 2 3 1 2 3 3 2 Battery removal - Fig. 11 This product contains lithium iron tetraphosphate rechargeable battery. To protect the environment, please discard the battery at the end of its working life according to current law. LiFePO4 Notes on how to achieve correct battery operations 1) Do not tamper with the control electronic circuit, do not tamper with the battery, do not short-circuit the battery.
12 Parts requiring frequent cleaning. Periodic cleaning - Fig. 12 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors such as wear and the work environment quality (air humidity, dust, salinity, etc.). To remove dirt from external parts, use a soft cloth dampened with any liquid glass cleaning detergent.
TECHNICAL DATA • Repeater: Receives the signal from the master and re-transmits it to other Slaves hidden from the master • XLR 5-pole DMX-in DMX-out standard sockets • Default macros, user programmable macros. • DMX recorder to save scene sequences.
CHANNEL FUNCTIONS GLOW UP STRIP 100 COMMON MODE CHANNEL SINGLE MODE 1 RED RED 2 GREEN GREEN 3 BLUE BLUE 4 WHITE WHITE 5 DIMMER RED 6 STROBE GREEN 7 MACRO COLOR BLUE 8 ZOOM WHITE 9 DIMMER 10 STROBE 11 MACRO COLOR 12 ZOOM GLOW UP STRIP 100 23 Continued ➔
COMMON MODE • RED - channel 1 • DIMMER - channel 5 BIT BIT EFFECT 255 COLOUR INSERTED 0 COLOUR EXCLUDED 255 0 • GREEN - channel 2 EFFECT OPEN (LIGHT) CLOSED (BLACK) • STOP / STROBE - channel 6 BIT EFFECT 255 COLOUR INSERTED 0 COLOUR EXCLUDED • BLUE - channel 3 • MACRO COLOR - channel 7 BIT EFFECT 255 COLOUR INSERTED 0 COLOUR EXCLUDED • WHITE - channel 4 BIT EFFECT 255 COLOUR INSERTED 0 COLOUR EXCLUDED GLOW UP STRIP 100 24 BIT EFFECT 248 - 255 240 - 247 232 - 239 224 - 231
• ZOOM - channel 8 BIT GLOW UP STRIP 100 EFFECT 255 WIDE BEAM 0 NARROW BEAM 25 Continued ➔
SINGLE MODE • RED - channel 1 • RED - channel 5 BIT BIT EFFECT EFFECT 255 COLOUR INSERTED 255 COLOUR INSERTED 0 COLOUR EXCLUDED 0 COLOUR EXCLUDED • GREEN - channel 2 • GREEN - channel 6 BIT BIT EFFECT EFFECT 255 COLOUR INSERTED 255 COLOUR INSERTED 0 COLOUR EXCLUDED 0 COLOUR EXCLUDED • BLUE - channel 3 • BLUE - channel 7 BIT BIT EFFECT EFFECT 255 COLOUR INSERTED 255 COLOUR INSERTED 0 COLOUR EXCLUDED 0 COLOUR EXCLUDED • WHITE - channel 4 • WHITE - channel 8 BIT BIT
• DIMMER - channel 9 • ZOOM - channel 12 BIT 255 0 EFFECT BIT 255 WIDE BEAM CLOSED (BLACK) 0 NARROW BEAM • STOP / STROBE - channel 10 • MACRO COLOR - channel 11 GLOW UP STRIP 100 EFFECT OPEN (LIGHT) BIT EFFECT 248 - 255 240 - 247 232 - 239 224 - 231 220 - 223 216 - 219 212 - 215 208 - 211 204 - 207 200 - 203 196 - 199 192 - 195 188 - 191 184 - 187 180 - 183 176 - 179 172 - 175 168 - 171 164 - 167 160 - 163 156 - 159 152 - 155 148 - 151 144 - 147 140 - 143 136 - 139 132 - 135 128 - 131 124 -
IST003/001 – EN - Rev.A 12/13 CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.
