ENGLISH ® GLOW UP & FLIGHT CASE C TW W C71050 C71055 C71060 F21230 INSTRUCTIONS MANUAL PR ARY N I M ELI CONTENTS Page Contents 2 Safety information 3 Unpacking and preparation 3 Installation and start-up 4 Control panel 7 Main menu 13 Manual zoom 13 Maintenance 14 Battery removal 15 Optional accessories 16 Technical data 16 Cause and solution of problems 17 Channel functions Congratulations on choosing a Clay Paky product! We thank you for your choice.
SAFETY INFORMATION GLOW UP • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.
SAFETY INFORMATION FLIGHT CASE • Installation Ensure that the Flight Case, when used for charging Glow UP, is positioned at a distance of 15 cm from any surface or wall, to allow proper ventilation. • Maximum ambient temperature Do not operate the device if ambient temperature (Ta) exceeds 40°C. IP20 • IP20 protection rating The fitting is protected against penetration by solid bodies of over 12mm (0.
UNPACKING AND PREPARATION 1 OPTIONAL ACCESSORY C71110 099114 Packing content - Fig. 1 INSTALLATION AND START-UP 2 Projector installation - Fig. 2 The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall. WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105015/801 available upon request).
CONTROL PANEL 4 Power Supply L N Connections to the power mains - Fig. 4 5 DMX 512 5 PIN 5 4 3 1 2 SCREEN SIGNAL SIGNAL DMX 512 DMX 512 3 PIN SIGNAL 1 2 SCREEN 3 SIGNAL Connections to the control signal line (DMX) - Fig. 5 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
Con Il GlowUp in condizione di riposo, il display visuallizza la pagina delle informazioni: DMX Address Time or percent remaining of the battery charge ADDR 001 DMX C Operating mode (see page 15) BAT 40% Yy Link status (Wireless or Wired) W Errors / Warning Display symbology- (Stato del Link) Transmission to DMX cable Reception from DMX cable Reception DMX from Radio (wireless) Transmission DMX from Radio (wireless) Initial projector address settings An initial address must be set on each single
8 4 3 1 2 Charging glow up - Fig. 8 From 1 to 6 Glow Ups can be simultaneously charged by appropriately connecting and powering the flight-case. 9 1 Fuse 6,3x32mm 3AT 250Vac (030471) 2 Fuse 6,3x32mm 10AT 250Vac (030470) Replacing flight case fuses - Fig. 9 Each flight-case has 2 fuses associated with the main power cord connection and one fuse for each Glow UP charge station.
MENU SET MAIN MENU 1 2 Program Edit scene 3 Setup DMX Address Edit Sequence Radio DMX recorder Mode Manual Control Color temperature (TW only) C TW W Red Channel 1 Dimmer Green Channel 2 Stop Strobe Blue Stop Strobe White Fixture ID Dimmer Display Stop Strobe Contrast Preset Colors Battery Display Factory 4 5 Information System version Advanced FW Uploader Charge Setup Model Charge Left CPU Reset Charge Hours Test DMX Monitor Radio Setup Charge Battery hours Discharge
Shortcut keys menu: By pressing the ENTER A key and UP B, the DMX address setting function can be quickly accessed.
PRESET COLORS for Stand Alone “GlowUp C” Colour Reference 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 LEE 101 LEE 103 LEE 105 LEE 107 LEE 111 LEE 113 LEE 115 LEE 116 LEE 119 LEE 128 LEE 132 LEE 134 LEE 135 LEE 136 LEE 147 LEE 180 LEE 156 LEE 079 LEE 194 LEE 024 LEE 017 LEE 019 LEE 108 LEE 126 LEE 141 ROSCO 378 ROSCO 358 ROSCO 081 ROSCO 066 ROSCO 030 ROSCO 318 ROSCO 332 ROSCO 034 ROSCO 039 RED GRE
PROGRAM MENU Program EDIT SCENE To create/overwrite/modify a SCENE customised by the user: 1) Press ENTER – SCENE 1 appears on the display. and DOWN keys to select from the ten available 2) Use the UP SCENES. 3) Press ENTER to open a SCENE. 4) A value can be associated with each GlowUp channel inside each SCENE using the UP and DOWN keys. 5) When finished with settings, press SELECT . A confirmation message appears: SAVE SCENE X ?.
A Press ENTER to confirm the selection (the display blinks for to keep the current settings and several seconds) or SELECT return to the previous Menu. S • MASTER OUTPUT: GlowUp runs as a Master and use the UP and DOWN keys to select Press ENTER come si desidera che venga trasmesso il segnale DMX ad altri apperecchi: Cable+Wireless Cable Wireless Press ENTER to confirm the selection (the display blinks for to keep the current settings and several seconds) or SELECT return to the previous Menu.
BATTERY DISPLAY Allows you to select how to display the battery charge in idle status. – current settings appear on the display. 1) Press ENTER and DOWN keys to select one of the 3 following 2) Use the UP options: Automatic: displays the remaining battery charge in hours or as a percentage. Percentage: displays the percentage of remaining battery charge. Time left: displays the remaining time of the battery charge in hours.
CHARGE HOURS Permette di selezionare come visualizzare la carica della batteria sul display in stato di riposo. 5) Premere ENTER per visualizzare le ore di carica della batteria. per tornare al Menu precedente. 6) Premere SELECT Charge Hours A S DMX MONITOR Displays the DMX input level in bit for each GlowUP channel. – the first channel appears on the display. 1) Press ENTER and DOWN keys to select the channel. 2) Use the to display the channel DMX level (value between 0 3) Press ENTER and 255).
A Premere ENTER per attivare la ricerca (wait .....) in caso di risultato positivo apparirà sul display la scritta OK. CHARGE BATTERY HOURS Permette di visualizzare le ore totali di carica della batteria dalla costruzione ad oggi. 1) Press ENTER – total charge hours appear on the display. to return to the previous Menu. 2) Press SELECT Charge Battery hours A S DISCHARGE BATTERY HOURS Displays total GlowUp battery powered operating hours from last time used, dalla costruzione ad oggi.
Modalità Stand Alone / DMX in play/pause Stand Alone / DMX in stop Master Slave Tx (master addr 1) Master Slave Rx (slave addr 1) (non va in play) DMX Memory Tx (master all addr) DMX Memory Rx (slave addr N) (non va in play) GLOW UP Slave Priority Repeater Master Output Testo Visualizzato sul display - Off - PLAY (o PAUSE) - Wireless to Cable + Repeat &Play - PLAYW→C (o PAUSW→C) - Cable to Wireless + Repeat & Play - PLAYC→W (o PAUSC→W) - Wireless to Cable + Repeater only - W→C -
MANUAL ZOOM 10 Antenna Aerial 1 2 Manual zoom - Fig. 10 The GlowUP has a manual zoom located on the back of the projector head.
BATTERY REMOVAL This product contains lithium iron tetraphosphate rechargeable battery. To protect the environment, please discard the battery at the end of its working life according to current law.
13 Parts requiring frequent cleaning. Periodic cleaning - Fig. 13 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors such as wear and the work environment quality (air humidity, dust, salinity, etc.). To remove dirt from external parts, use a soft cloth dampened with any liquid glass cleaning detergent.
TECHNICAL DATA Source 4 10 W MC-E Cree leds Absorbed power 50W max - 170 VA Led pilot power 40W Body • Injection pressed ABS case (UV protected) • Finish: Polished metallic – Painted White or Black • carrier handle • 4 non-slip rubber feet Optics Optic zoom, manually adjustable, magnetic support for any additional diffusers 226 (8,90") Fittings 2 fast-look holes for omega hook-up LED color temperature 5700°C GlowUP C 6000°C GlowUP W 6200°C cool white GlowUp TW 2700°C warm white GlowUp TW 4200°C cool+w
CHANNEL FUNCTIONS GLOW UP C CHANNEL MODE CHANNEL 1 RED 2 GREEN 3 BLUE 4 WHITE 5 DIMMER 6 STOP / STROBE 7 MACRO COLOR 8 MACRO TIMING 9 MACRO FADING GLOW UP TW CHANNEL MODE CHANNEL INDEPENDENT CONSTANT INTENSITY 1 COOL WHITE 6200°K TUNABLE WHITE TUNABLE WHITE 2 WARM WHITE 2700°K DIMMER DIMMER 3 STOP / STROBE STOP / STROBE STOP / STROBE GLOW UP W CHANNEL GLOW UP MAX INTENSITY CHANNEL MODE 1 DIMMER 2 STOP / STROBE 21
• MACRO COLOR - channel 7 GLOW UP C BIT 248 - 255 240 - 247 232 - 239 224 - 231 220 - 223 216 - 219 212 - 215 208 - 211 204 - 207 200 - 203 196 - 199 192 - 195 188 - 191 184 - 187 180 - 183 176 - 179 172 - 175 168 - 171 164 - 167 160 - 163 156 - 159 152 - 155 148 - 151 144 - 147 140 - 143 136 - 139 132 - 135 128 - 131 124 - 127 120 - 123 116 - 119 112 - 115 108 - 111 104 - 107 100 - 103 96 - 99 92 - 95 88 - 91 84 - 87 80 - 83 76 - 79 72 - 75 68 - 71 64 - 67 60 - 63 56 - 59 52 - 55 48 - 51 44 - 47 40 - 43 3
GLOW UP TW INDEPENDENT MODE CONSTANT INTENSITY & MAX INTENSITY MODE INDEPENDENT CONSTANT INTENSITY MAX INTENSITY COOL WHITE 6200°K TUNABLE WHITE TUNABLE WHITE WARM WHITE 2700°K DIMMER DIMMER STOP / STROBE STOP / STROBE STOP / STROBE CONSTANT INTENSITY 100 COOL • COOL WHITE - channel 1 100 50 50 % EFFECT 255 100 WHITE INSERTED 0.0 4200°C 0 6200°C 0 2700°C BIT % 255 100 WARM WHITE EFFECT 0 0.
GLOW UP W • DIMMER - channel 1 BIT % 255 100 OPEN (LIGHT) EFFECT 0 0.0 CLOSED (BLACK) PRELIMINARY 06/12 Cod. 099114-EN gfstudio.com • STOP / STROBE - channel 2 CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.
