Specifications

ManualsBrandsCLEAN BURN ManualsFurnaceCB-1400

Updated – October 2013

4109 Capital Circle

Janesville, WI

USA 53546

www.cleanburn.com

SPECIFICATIONS FOR CLEAN BURN WARM AIR FURNACE

MODEL CB-1750 CENTRAL FURNACE

PART 1 – GENERAL

1.1 DEFINITIONS: Throughout this bid specification the word “shall” appears frequently. The

word “shall” indicates a mandatory requirement as per the Codes and Regulations that

are listed in Part 1 – Section 1.4 through 1.4.4 of this bid specification as applicable.

1.2 REQUIREMENTS:

General provisions of the purchase specifications, including general

and other conditions, delivery requirements, shipping and demurrage charges will be

under separate cover and shall apply.

1.3 SCOPE:

This specification covers but is not limited to the furnishing of a CB-1750,

170,000 BTU/hr (input) Central Furnace Package. Thi s package will include the

following:

¾ One (1) CB-1750, 170,000 BTU/hr input central furnace (136,000 BTU/hr output)

¾ One (1) CB-525-S2 used-oil firing burner

¾ One (1) F-180 fan switch

¾ One (1) L-200 high limit switch

¾ One (1) L-290 auxiliary high limit switch (automatic reset)

¾ One (1) Lux Pro PSD Series 45 to 90

F 24 vac wall mounted digital thermostat with

positive off position (non mercury)

¾ One (1) Suntec used oil pump assembly (Refer to Part 1 – Sectio n 2.5 for the listed

pump options)

¾ One (1) Oil pump relief valve assembly

¾ One (1) Lenz # DH750-100 canister filter with a washable 100-mesh stainless steel

screen filter element

¾ One (1) Oil vacuum gauge

¾ One (1) ¾” x ¾” in-line brass check valve

¾ One (1) ¾” in-line washable 50-mesh stainless steel screen filter eleme nt for the

check valve

¾ One (1) CB-1750 blower kit with a 3/4 h p motor @ 1,075rpm, semi enclosed, ODP,

PSC, sleeve bearing, cw-se rotation, 48YZ frame, direct drive (resilient) mounted,

” diameter fan motor, with a 10 uf (mfd) / 370 vac capacitor, delivering 1,700 cfm

of free air when used as a unit heater (no ductwork added). When adding ductwork

with the louvers fully ope ned and in stalled inside of the ductwork, you si ze the

ductwork fro 0.25” W.C. to deliver 1,550 cfm of d ucted air, or when you remove the

louvers and add ductwork, you size the ductwork for 0.40” W.C. to deliver 1,400 cfm

of ducted air

Summary of content (12 pages)

PAGE 1
Updated – October 2013 4109 Capital Circle Janesville, WI USA 53546 www.cleanburn.com SPECIFICATIONS FOR CLEAN BURN WARM AIR FURNACE MODEL CB-1750 CENTRAL FURNACE PART 1 – GENERAL 1.1 DEFINITIONS: Throughout this bid specification the word “shall” appears frequently. The word “shall” indicates a mandatory requirement as per the Codes and Regulations that are listed in Part 1 – Section 1.4 through 1.4.4 of this bid specification as applicable. 1.
PAGE 2
¾ ¾ ¾ ¾ ¾ One (1) Field Type ‘M’, 8” barometric damper One (1) 8”, 24-gauge galvanized sheet metal cap One (1) CB-1750 Operator’s Manual Burner oil line and air line components Miscellaneous bolts and fittings for assembly / installation of the appliance Note: This is the standard package for the CB-17 50 Central Furnace. This appliance can be in stalled as a unit heater without ductwork installed, or as a central furnace with the properly sized ductwork installed.
PAGE 3
PART 2 – PRODUCT 2.1 FURNACE: The ap pliance shall be shipped factory assembled and pre-wired as a single, packaged unit suitable for firing used-oils. 2.1.1 The appliance shall be UL / ULC listed and tested to burn the used-oils as per NFPA 31, Chapter 12, Section 12.4.1, 12.4.2, and 12.4.3. 2.1.2 The appliance shall be complete with one used-oil burner assembly, one used-oil pump assembly, and all devices and controls required for safe and efficient operation. 2.
PAGE 4
2.2.10 The appliance shall be provided with a wrap around 22-gauge, galvaneal steel jacket with a baked on powder coat finish. 2.2.11 The size, capacity, and operation of t he appliance shall be designed as shown in the following: ¾ 170,000 BTU/hr input rating ¾ 136,000 BTU/hr output rating ¾ 1.
PAGE 5
2.3.5 When installing this appliance in a confined space, the minimum amount of combustion air supplied to this appliance shall be from two permanent openings, one opening installed within 12” of the ceiling of the room and one opening installed within 12” of the floor of the room, with each opening totaling 49 square inches at a rate of 188 cfm of free air for a single appliance application as per the Codes and Regulations that are listed in Part 1 – Section 1.4 through 1.4.
PAGE 6
2.3.13 On-site certification of the appliance may be required by the Authority Having Jurisdiction (AHJ). It is the re sponsibility of the purch aser, designated agent, contractor, or installer of the ap pliance to check with the AHJ a s to th e proper procedures to follow for the completion of this installation. 2.3.
PAGE 7
2.4.11 If the primary safety control fails while in operation but the flam e has been established and proven, the p rimary safety control shall be of a recycling type whi ch will allow the burner up to three retries for ignition before the control will “lock-out”. 2.4.12 The primary safety control shall be co mpletely wired and tested b y the manufacturer for this safety function. 2.4.
PAGE 8
2.5 USED-OIL FUEL SYSTEM: The CB-1750 Central Furnace is available with two choices of oil pumps that are both rated for use with used-oil applications. The pumps will have the following description: Option #1 – Metering Pump Assembly ¾ One (1) Suntec model A2RA-7710 used-oil pump assembly with a 1/20th hp motor @ 196 rpm, TENV, DP, PS C, sealed, ball bearing, ccw-se rotation, 10 0 AC frame, parallel shaft, close coupled stud m ounted, 3.
PAGE 9
2.5.7 The Suntec model J4NB-A1000G use-oil pump (option # 2 ) shall have a n adjustable pressure range of 20 to 40 psig. 2.5.8 The Suntec model J4NB-A1000G use-oil pump (option # 2) shall have a washable 234-micron stainless steel filter screen installed inside of the pump head. (Refer to the CB-1750 Operator’s Manual and the J-Pump Inst aller’s Manual for the proper installation of this pump.) 2.5.
PAGE 10
2.6.5 DO NOT US E Type ‘B’ or ‘BW’ Vent which is a non-insulated double walled stack approved for LP and natural gas fired a ppliances only as per the Codes and Regulations that are listed in Part 1 – Sections 1.4 through 1.4.4 of this bid specification as applicable. 2.6.6 DO NOT USE Type ‘L’ Vent whi ch is a non-insulated double walled stack approved for some #2 fuel oil an d pellet burning appliances only as per the Codes and Regulations that are listed in Part 1 – Sections 1.4 through 1.4.
PAGE 11
PART 3 – ADDITIONAL INFORMATION 3.1 GENERAL: The in stallation of this appliance shall be mad e in accordance with the manufacturers’ instructions, as well as in accordance with all Federal, State, Regional, or Local Laws and / o r Regulations acceptable to th e Authority Having Jurisdiction (AHJ) and shall b e accomplished only by a qualifi ed, certified, a nd competent heating technician experienced in making such installations as per NFPA 31, Chapter 4, Sections 4.3.2 and 4.3 .
PAGE 12
PART 4 – WARRANTY 4.1 WARRANTY INFORMATIOIN: Cl ean Burn, LLC. shall warrant the CB-17 50 Central Furnace and all oth er Clean Burn products to be free from defects in material and workmanship under normal use according to the provisions and limitations set in the CB1750 Operator’s Manual for a period of one year from the date of purchase by the original purchaser. 4.1.