CLEANMAX OPERATING INSTRUCTIONS FOR C LEAN M AX PRO SERIES UPRIGHT VACUUMS MODELS : CMPS-1T CMPS-1N Before operating the vacuum, please read these instructions completely.
Index Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Replacement Bags/Filters . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. When using an electrical appliance, basic precautions should always be followed, including the following: SAVE THESE INSTRUCTIONS. WARNING! To reduce the risk of fire, electric shock, or injury: 1. Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing. 2. WARNING: ELECTRIC SHOCK COULD OCCUR IF USED OUTDOORS OR ON WET SURFACES. 3. Do not allow to be used as a toy.
Grounding Instructions This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Parts Identification Cord storage hook Handle tube Power cord On/Off switch Bag compartment cover latch Easy-carry handle Bag compartment Accessory attachment opening Nozzle hose Tools (CMPS-1T only) Nozzle hose Model specification plate Furniture guard Self-adjusting nozzle Thermal reset button Thermal reset instructions Replacement Bags and Filters • Genuine CleanMax Vacuum Bags Part # 06.
How to Assemble and Operate the Vacuum How to Attach the Handle to the Vacuum Cleaner The vacuum cleaner and the handle are packed separately. 1. After first removing the handle screw, insert handle into the hole on top of the vacuum cleaner. Make sure that the cord hook on the handle is positioned to the back of the vacuum cleaner (Fig. 1). 2. Line up the small hole on the handle with the small hole on the vacuum cleaner and insert the screw. Make sure the screw is tightened securely. On/Off Switch (Fig.
Handle Adjustments The handle on this vacuum cleaner can be set to one of three positions – upright, middle or low. How to Adjust the Handle 1. To release the handle, step on the left rear corner of the vacuum cleaner (Fig.1). 2. Upright position – for when cleaning tools are being used or for storage (Fig 2). Handle locks in this position. 3. Middle position – for normal cleaning (Fig. 3). 4. Low position – for cleaning under furniture (Fig. 4).
Automatic Self-Adjusting Nozzle Your CleanMax upright vacuum cleaner is designed with an Automatic Self-Adjusting Nozzle. No manual adjustments are required. The height of the nozzle is instantly and automatically adjusted to carpet pile height. This self-adjusting feature allows the nozzle to float evenly over all carpet pile surfaces. Optional Cleaning Tools/Accessories Deluxe Attachment Set 05.119 (Fig.
How to Replace the Vacuum Belt CAUTION: Unplug the vacuum cleaner before performing any of these steps. How to Remove the Bottom Plate 1. Place the vacuum cleaner in the low position (see page 6). Turn the vacuum over. 2. Slide the clips toward each other (Fig. 1). 3. Remove the bottom plate. How to Replace the Belt 1. Turn the unit over and remove the bottom plate as described in the above section. 2. Lift the belt cover and turn toward the outside (Fig. 2 & 3). 3.
How to Clean the Nozzle Hose CAUTION: Unplug the vacuum cleaner. The nozzle hose, located on the back of the vacuum cleaner, carries the dirt from the nozzle to the vacuum bag. The hose also functions as the attachment cleaning hose (on CMPS-1T model only). If the hose should become clogged 1. Pull out and turn the lid of the cleaning attachment opening. Remove the clog or blockage (Fig.1). 2. If the above step is not enough, remove hose cuff from the attachment port inlet (Fig. 2).
Thermal Fuse Protection Your CleanMax vacuum cleaner comes equipped with a Manual Reset Thermal Fuse Protector. This thermal protector is designed to protect your vacuum cleaner from overheating due to a cutoff in airflow (i.e. clogged hose, operating the vacuum without a bag). Should this situation occur, the thermal fuse protector will safely shut off your vacuum cleaner to avoid any potential damage. To reset the thermal fuse 1. Unplug the vacuum cleaner. 2.
CLEANMAX CleanMax Vacuum Cleaners PO Box 730 Fenton, MO 63026 ©2006 CleanMax Vacuum Cleaners.